Qsig MWI CallManager

[sfcstroud]

Message waiting Indicator is not light in Cisco phones. I have enabled Qmwi on the qsig, however have yet to light the phones. Understanding that the 4 digit number (FNA/Hunt) routes to Callpilot, how is the MWI indicator then transported back to the set? Additionally what can I look for in the d channel messaging to determine rejects of this lighting up function?

 

[johnpoole]

you can monitor the d via ld 97 enl msgo x with x=to the d.. that's outging, incoming is enl msgi x. to dial your cisco phones, are you dialing just the dn of the set.. my cisco wireless is 4040.. my nortel is 4041.. if your dialing a steering code or access code, then that could be your problem.. qmwi should be all that is needed for msgs in rcap.. are you gettings dns and names to and from the cisco?

you may need the pni number on both routes and in the cdb and the qsig has to be internal.. nortel does not light external stations.. you can't light a lamp on your home phone, unless you have an internal tie to that station..

john poole
bellsouth business
columbia,sc

 

[johnpoole]

RCAP COLP NDI CCBI CCNI PRI DV3I CTI  QMWI

IFC ISGF in internal, IFC ESGF is external


john poole
bellsouth business
columbia,sc

 

[sfcstroud]

This is my current configuration.

ADAN DCH 85
CTYP MSDL
GRP 1
DNUM 8
PORT 3
DES Cisco_CCM
USR PRI
DCHL 85
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID 25
RCAP COLP NDI CCBI CCNI PRI DV3I CTI QMWI
PR_TRIGS DIV 2 3
CNG 2 3
CTR2 2 3
PR_RTN NO
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

REQ PRT
TYPE: rdb
CUST 0
ROUT 81

TYPE RDB
CUST 00
ROUT 81
DES CISCO
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
IDEF NET
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ISGF
SBN NO
PNI 00001
NCNA NO
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 3058
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 1
NDNO 1 *
DEXT NO
DNAM NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048


PAGE 002

NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR YES
INC NO
LAST NO
QREC NO
OAL YES
AIA NO
OAN YES
OPD NO
CDRX NO
NATL YES
VRAT NO
MUS NO
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

REQ prt
CUST 0
FEAT cdp
TYPE dsc
DSC 1201
DSC 1201
FLEN 4
DSP LSC
RLI 8
NPA (xxx)masked for security
NXX (xxx)masked for security


DES CISCO_CCM
TN 074 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 7
RTMB 81 1
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD HKD
P10 VNL
TKID
DATE 14 DEC 2006

With this config I net no MWI on cisco and receive the following dch info.

DCH 85 UIPE_OMSG CC_SETUP_REQ REF 00000013 CH 85 5 TOD 7:55:18 CK BFC8FE28
PROGRESS: ORIGINATING END IS NOT ISDN
CALLING #:9699 NUM PLAN: PRIVATE TON: ESN CDP
CALLED #:1201 NUM PLAN: PRIVATE TON: ESN CDP

DCH 85 UIPE_IMSG CC_PROCEED_IND REF 00000013 CH 85 5 TOD 7:55:20 CK BFC8FF47

DCH 85 UIPE_IMSG CC_ALERT_IND REF 00000013 CH 85 5 TOD 7:55:20 CK BFC8FF57
PROGRESS: INBAND INFO OR PATTERN IS AVAIL

DCH 85 UIPE_IMSG CC_SETUP_IND REF 00000280 CH 85 23 TOD 7:55:32 CK BFC95DAC
CALLED #:9889 NUM PLAN: UNKNOWN TON: UNKNOWN
PROGRESS: ORIGINATING END IS NOT ISDN
CALLING #:9699 NUM PLAN: PRIVATE TON: ESN CDP

DCH 85 UIPE_OMSG CC_PROCEED_REQ REF 00008280 CH 85 23 TOD 7:55:32 CK BFC95DD3

DCH 85 UIPE_OMSG CC_ALERT_REQ REF 00008280 CH 85 23 TOD 7:55:32 CK BFC95E4D

DCH 85 UIPE_IMSG CC_PROGRESS_IND REF 00000013 CH 85 5 TOD 7:55:32 CK BFC95E99
PROGRESS: INBAND INFO OR PATTERN IS AVAIL

DCH 85 UIPE_IMSG CC_FAC_IND REF 00000013 CH 85 5 TOD 7:55:32 CK BFC95EBD

DCH 85 UIPE_OMSG CC_SETUP_RESP REF 00008280 CH 85 23 TOD 7:55:32 CK BFC96234
CONNECT #:9889 NUM PLAN: UNKNOWN TON: UNKNOWN

DCH 85 UIPE_IMSG CC_SETUP_CONF REF 00000013 CH 85 5 TOD 7:55:32 CK BFC962F9
CONNECT #:9889 NUM PLAN: UNKNOWN TON: UNKNOWN

DCH 85 UIPE_IMSG CC_SETUPCOMP_IND REF 00000280 CH 85 23 TOD 7:55:32 CK BFC96310

DCH 85 UIPE_OMSG CC_DISC_REQ REF 00000013 CH 85 5 TOD 7:55:44 CK BFC9BF5D
CAUSE: #16 - NORMAL CALL CLEARING

DCH 85 UIPE_IMSG CC_DISC_IND REF 00000280 CH 85 23 TOD 7:55:44 CK BFC9BFC4
CAUSE: #16 - NORMAL CALL CLEARING

DCH 85 UIPE_OMSG CC_RELEASE_REQ REF 00008280 CH 85 23 TOD 7:55:44 CK BFC9BFCC

DCH 85 UIPE_IMSG CC_RELEASE_IND REF 00000013 CH 85 5 TOD 7:55:44 CK BFC9BFF0

DCH 85 UIPE_OMSG CC_RELEASE_RESP REF 00000013 CH 85 5 TOD 7:55:44 CK BFC9BFFC

DCH 85 UIPE_IMSG CC_RELEASE_CONF REF 00000280 CH 85 23 TOD 7:55:44 CK BFC9C055

 

[johnpoole]

do you have an ext in the cisco 9899 and 9699.. is so what are those number built as in the switch?.. how do they get to the pri? your route and d should work

john poole
bellsouth business
columbia,sc

 

[sfcstroud]

9699 is my DN(Nortel) and 9889 is VM pilot. Cisco will be here shorlty to finish the install. I will try to get his config info. I had provided him everything. According to him the entire range is there.

 

[johnpoole]

as long as your dialing just the dn of a cisco and that same dn is the mwi in cp.. i had one where the users dialed 7 plus the 4 digit cisco dn(1000), 7 was a dsc to the qsig.. those lamps would not work.. of course the cisco did not know what to do with 71000.. when i made 1000 the dsc, lamps worked

lamp req =71000
far end reject

lamp req 1000
far end ack

john poole
bellsouth business
columbia,sc