Qsig MD110(BC10)-Mxone 3.1

[DEIVIDOS]

Hi,
I have a system with Mx-One 3.1 Sp 1 and Md 110 in BC 10, the problem is
that the PRA is on the MD 110.
The call goes through the MD and is received in one extension of the
Mx one.
The problem is that the number is received without 0 ahead of
the numbers.
the configuration is this:

In MD 110:

<RODDPEST=9585;
EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
xxxx 35 0606100000000250006 0 1 0

END

<ROCAP:ROu=35;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
35 511000000000001 4 3110030000 0 30 128 03151515 111110000031 111111

END

<RODAP:ROu=35;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
35 SL60 H'00000310 H'15440000 H'06300000 NO

< NUTRP;
<nutrp;
NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP ROU TARDST PRE TRC NEWTYP CONT BCAP HLC
94466xxxx 0 0 xxxx 9 0
94466xxxx 0 2 xxxx 9 0
94466xxxx 0 4 xxxx 9 0

In Mx One :

MDSH> rocap:rou=88;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
88 5110000000000010 4 3110030000 0 30 128 03151515 111110000031 111111

END

MDSH> rodap:rou=88;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
88 SL60 H'00000310 H'15440000 H'06000000 NO

MDSH> number_conversion_print
Number conversion data:
Entry Cnvtyp Numtyp Rou Tardest Pre Trc Newtyp Cont Bcap Hlc
6 2 0 0
6 2 2 0
6 2 4 0
8 2 2 0
8 2 0 0
8 2 4 0
9 2 2 0
9 2 0 0
9 2 4 0

The Cnvtype 2 to put the 0 ahead the number, but it`s not work.
also i try to put the Cnvtyp 2 with different values 1,3,5,6 ....
Any ideas??

 

[whosrdaddy]

nutri:entry=1,cnvtyp=2,numtyp=1,pre=000;
nutri:entry=2,cnvtyp=2,numtyp=1,pre=000;
nutri:entry=3,cnvtyp=2,numtyp=1,pre=000;
nutri:entry=4,cnvtyp=2,numtyp=1,pre=000;
nutri:entry=5,cnvtyp=2,numtyp=1,pre=000;
nutri:entry=6,cnvtyp=2,numtyp=1,pre=000;
nutri:entry=7,cnvtyp=2,numtyp=1,pre=000;
nutri:entry=8,cnvtyp=2,numtyp=1,pre=000;
nutri:entry=9,cnvtyp=2,numtyp=1,pre=000;
nutri:entry=1,cnvtyp=2,numtyp=2,pre=00;
nutri:entry=2,cnvtyp=2,numtyp=2,pre=00;
nutri:entry=3,cnvtyp=2,numtyp=2,pre=00;
nutri:entry=4,cnvtyp=2,numtyp=2,pre=00;
nutri:entry=5,cnvtyp=2,numtyp=2,pre=00;
nutri:entry=6,cnvtyp=2,numtyp=2,pre=00;
nutri:entry=7,cnvtyp=2,numtyp=2,pre=00;
nutri:entry=8,cnvtyp=2,numtyp=2,pre=00;
nutri:entry=9,cnvtyp=2,numtyp=2,pre=00;

should work... (covert these to MX-One commands)

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[DEIVIDOS]

Thanks ,but don´t work.
the problem now is if yoU call to a extension in Md 110 the number appear 00685xxxxxxx.
and if you call to a extension in Mxone the result is the same .

I have put anything in ADC of RODDI for example.

best regards

 

[whosrdaddy]

Duh, I see your problem:

last digit of SERV in the ROCAP must be set to 1 to enable number conversion...

Cheers,
Daddy

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[DEIVIDOS]

Thanks whosrdaddy,
you are a machine, now all works fine.

thanks and best regards