Q.Sig over TLU 76

[MirkoGradassi]

Hi all, I'm trying to interconnect a BP 250 with a Md100 via TLU 79. Everything is working fine if I configure the machine with standard ISDN protocol.

When I try to change the protocol and use Q.sig nothing work. I cannot call from Md110 , my extension report "category not allowed" and disconnect with fast busy. If I try to call from BP to MD110 the call remain suspended anda after 10 second it disconnect.

the extension on MD side are 5xx and on BP side are 2xx.

My configuration on MD side is:

***********************************************************
<rodap:ROU=ALL;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
1 SL60 H'00000314 H'15400000 H'0EA10000 NO
2 SL60 H'00000204 H'35400000 H'0EA10000 NO

END

<rocap:ROU=ALL;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
1 512000010000 5 3110000001 0 30 128 00151515 011100000030 101110
2 511000010000 5 3101000001 0 30 128 00151515 111100000030 101110

END

<KSCAPIR=501;
KEY SYSTEM CATEGORY PRINT
DIR TRAF SERV CDIV ROC ITYPE TRM ADC
501 03151515 02121206 011150000 0000 19 0 00000000010

END

<RODDPEST=ALL;
EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
200 1 050500000000025000 0 1 0
3 1 000500000000025000 0 2 0 2
790 2 000500000000025000 0 4 0

END

<ROEDP:ROU=ALL,TRU=ALL;
ROUTE EQUIPMENT DATA
ROU TRU EQU SQU INDDAT
1 001-1 001-0-40-00 H'000000000000
1 001-2 001-0-40-01 H'000000000000
2 001-1 001-0-40-02 H'000000000000
2 001-2 001-0-40-03 H'000000000000

END

<RONDP:ROU=ALL;
ROUTE NUMBER DATA
ROU PRE ROUDIR EXNOPU EXNOPR TERAC
1
2

END

<NADAP:LIM=1;
NUMBER ANALYSIS DATA
TYPE OF SERIES NUMBER SERIES
EXTENSION NUMBER SERIES 501 - 550
EXTERNAL DESTINATION CODE 200
3
790
OPERATOR INDIV. NUMBER SERIES 500
OPERATOR COMMON NUMBER SERIES 9
OPERATOR COM. DID. NUM. SERIES 1
ABBREVIATED COMMON NUMBER SERIES 551 - 560
TYPE OF SERVICE CODE SERVICE CODE
EXTERNAL NUMBER LENGTH DATA
EXTERNAL NUMBER NUMBER LENGTH
PROCEED TO SEND SIGNAL DATA
EXTERNAL NUMBER POS. TYPE
CALL DISCRIMINATION DATA
EXTERNAL/INTERNAL NUMBER CAT
2 5 4 3 2 1 0
3 5 4 3 2 1 0
4 5 4 3 2 1 0
5 5 4 3 2 1 0
6 5 4 3 2 1 0
8 5 4
9 5 4 3 2 1 0
END

<NUTRP;
NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP PRE TRC NEWTYP CONT BCAP HLC
5 2 2 0 0
END

<
**********************************************************

ANY IDEAS?

Bye
Mirko

 

[MirkoGradassi]

YuhuuuuuI've solved it changing VARO:

RODAI:ROU=01,TYPE=SL60,VARC=00000314,VARI=15400000,VARO=4E300000;

Thanks
Mirko