PROGRAMMING AN ANALOG LINE ON A 2616 KEY

[norteldiva]

Can someone please tell me how to program an analog line onto a 2616 key?

The manual says KEY 03 PVR XXXX with XXXX being the DN that the Line is pointed to.

Where do you assign a specific line to a DN?

My route is 2 1 for line 1 and 2 2 for line 2
2999 is my ACOD for the Route
and my TKID is 5000 for line 1 and 5001 for line 2.

Any assistance would be greatly appreciated!
Thanks!

 

[norstarboy125]

I don't know what you did so far but you need to follow these steps.

1. Build a new route unless your system already has one built, most of the times they are route 31.

2. Build a new COT trunk.

3. Find a unused dn, try to pick something outside your usual dn range.

4. Add the new PVR dn to a key.


Charm City Communications

http://www.charmcitycommunications.com

 

[StanleySteamer]

When you create the route you need to have
PRIV YES

 

[Firebird Scrambler]

This guide of mine is very old, but it should help you.

PRIVROUT.TXT
CONFIGURATION OF A PRIVATE LINE ROUTE USING XCOT TRUNKS.
ON A OPTION 11 18.40H 08/05/1996
>LD 16
REQ NEW
TYPE RDB ------------------------- ROUTE DATA BLOCK
CUST 0 ------------------------- CUSTOMER
DMOD
ROUT 19 ------------------------- ROUTE No.
TKTP COT ------------------------- TRUNK TYPE
PRIV YES ------------------------- PRIVATE ROUTE YES/NO
SAT
RCLS
DTRK
PTYP
ICOG IAO ------------------------- INCOMING & OUTGOING
SRCH
TRMB NO ------------------------- TROMBONE
STEP
TARG
SGRP
OABS
CNTL YES ------------------------- CHANGE CONTROL PARAMETERS
TIMR
SST
DTD YES ------------------------- DIAL TONE DETECT
XTDT 0 ------------------------- EXTENDED TONE DETECTOR TABLE
MDTD
DTDF SCDT 2 DT NEDC FEDC CPDC SPCT HOLD
SEIZ RGFL RVSD ILLR
DDO
DRNG YES ------------------------- DISTINCTIVE RINGING
NDRI
CDR YES }
INC YES }
TTA YES }
ABAN YES } ---------------------- CALL DETAIL RECORDING
QREC YES }
OAL YES }
AIA YES }
OAN YES }
OPD
NDP
OPA
CCO
NATL
SSL
CFWR
IDOP
MUS
MR PPM ------------------------- MESSAGE REGISTRATION TYPE
PANS
RUCS RPPM 0 MANO EQAR OHQ OHQT TTBL OHTD
RCAL ALRM PECL
DCTI
TIDY

REQ ****

>LD 14
REQ NEW
TYPE COT ----------------------- CENTRAL OFFICE TRUNK
TN 14 0 ----------------------- LOOP/UNIT
XTRK XCOT ------------------- EXTENDED CENTRAL OFFICE TRUNK CARD
CDEN
CUST 0 ----------------------- CUSTOMER
NCOS 7 ----------------------- NETWORK CLASS OF SERVICE
RTMB 19 1 ----------------------- ROUTE/MEMBER
PRDN 6002 ----------------------- PRIVATE LINE DN
CMF
SIGL GRD ----------- SIGNALLING (GRD = GROUND START,LGR = LOOP-
BIMP -CALLING GUARDED RELEASE)
SUPN YES ---------------------- ANSWER & DISCONNECT SUPERVISION
BTID
CLS DTN ----------------------- DIGITONE
TKID

REQ ****

>LD 11
REQ NEW
TYPE 2616
TN 18 12
DES TEST
CUST 0
AOM
FDN
TGAR
LDN
NCOS
RNPG
SSU
SCPW
SGRP
CLS
HUNT
LHK
SCI
AST
IAPG
KEY 0 SCR 4005
MARP
KEY 1 PVR 6002 ------------------ PRIVATE LINE KEY
MARP
KEY 2 TRN
KEY 3 CFW 4
KEY 4 RNP
KEY 5 RGA
KEY 6 RDL
KEY

REQ ****

>

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[trvlr1]

Is this a regular ground start or loop start line that already terminates to the PBX, or are you looking to add it?
If it is already in the PBX, you should be able to look at the TN programming in LD 11 or 20 or whatever and look for DFDN. This will give you the option to send it to a specific DN within the PBX. You can specify an existing number, or program up a new number on the phone, can be just a standard extension configuration on the phone ie SCR 1234.
If DFDN does not appear, check in the Manual, LD 14 and you should find how to set that up.