Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Problem with IP Office MFC R2 signaling

Status
Not open for further replies.

Juancho2015

Technical User
Aug 3, 2015
179
AR
Hi guys!

I have installed a brand new IPO 500V2 release 9.0.7 with an E1 trunk card configured for R2-MFC signaling. When a call tries to get into the system and the incoming number (DNIS) is complete, the IPO sends A1 signal (send next digit, asking for more digits) instead of A3 (address complete), and does not ask for ANI (with A5 signal). The call does not establish, of course.
- The country is Argentina.
- The CO sends 6 digits DNIS and the IPO is configured for receiving 6 digits too.
- The DNIS is (during tests) "700200" and is being routed throgh ICR to extension 1212
- For some reason the CO does not send I.15 (end of dial) signal after A1, and the IPO drops the call by sending a4 signal (congestion) after waiting 15 seconds.

Captures of config:

channels_n15v5v.jpg

Advanced_E1_fejp74.jpg
MFC_A_iyimwi.jpg

ICR_hjzfsp.jpg


Trace taken on Monitor:

1249928mS R2Channel: R2_ARG_9.1: EventRx: Seize State: Idle
1249928mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), speech path off
1249928mS R2Dialler: R2_ARG_9.1: MFC State Change: Idle -> Bwd 0
1249928mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), digit receiver R2 forwards
1249928mS R2Channel: R2_ARG_9.1: State Change Idle -> SeizeAck
1249928mS R2Channel: R2_ARG_9.1: EventTx: SeizeAck State: SeizeAck
1249929mS R2Channel: R2_ARG_9.1: State Change SeizeAck -> Dialling
1249929mS R2Channel: R2_ARG_9.1: EventTx: Dialling State: Dialling
1249929mS R2Line: line: 9.1: State= Idle RxMessage: Alert_PreIndication
1249930mS R2Line: line: 9.1: State Change Idle -> IncomingGuard
1250041mS R2DSP: PRIU DSP 3: read tone, port 0, channel 1, tone 0x07
1250042mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 RX Fwd MFC: I.7 - "7"
1250042mS R2Channel: R2_ARG_9.1: EventTx: Dialling State: Dialling
1250042mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 TX Bwd MFC: A.1 - SendNextDigit
1250042mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 1 (tone 33)
1250042mS R2Line: line: 9.1: State= IncomingGuard RxMessage: ReceivedDigit
1250043mS R2Line: line: 9.1: Routing Digit Received 7
1250109mS R2DSP: PRIU DSP 3: read tone, port 0, channel 1, tone 0x10
1250109mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 16 (tone 32)
1250184mS R2DSP: PRIU DSP 3: read tone, port 0, channel 1, tone 0x0a
1250184mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 RX Fwd MFC: I.10 - "0"
1250184mS R2Channel: R2_ARG_9.1: EventTx: Dialling State: Dialling
1250184mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 TX Bwd MFC: A.1 - SendNextDigit
1250185mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 1 (tone 33)
1250185mS R2Line: line: 9.1: State= IncomingGuard RxMessage: ReceivedDigit
1250185mS R2Line: line: 9.1: Routing Digit Received 0
1250251mS R2DSP: PRIU DSP 3: read tone, port 0, channel 1, tone 0x10
1250251mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 16 (tone 32)
1250326mS R2DSP: PRIU DSP 3: read tone, port 0, channel 1, tone 0x0a
1250326mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 RX Fwd MFC: I.10 - "0"
1250327mS R2Channel: R2_ARG_9.1: EventTx: Dialling State: Dialling
1250327mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 TX Bwd MFC: A.1 - SendNextDigit
1250327mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 1 (tone 33)
1250327mS R2Line: line: 9.1: State= IncomingGuard RxMessage: ReceivedDigit
1250327mS R2Line: line: 9.1: Routing Digit Received 0
1250385mS R2DSP: PRIU DSP 3: read tone, port 0, channel 1, tone 0x10
1250385mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 16 (tone 32)
1250460mS R2DSP: PRIU DSP 3: read tone, port 0, channel 1, tone 0x02
1250460mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 RX Fwd MFC: I.2 - "2"
1250461mS R2Channel: R2_ARG_9.1: EventTx: Dialling State: Dialling
1250461mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 TX Bwd MFC: A.1 - SendNextDigit
1250461mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 1 (tone 33)
1250462mS R2Line: line: 9.1: State= IncomingGuard RxMessage: ReceivedDigit
1250462mS R2Line: line: 9.1: Routing Digit Received 2
1250527mS R2DSP: PRIU DSP 3: read tone, port 0, channel 1, tone 0x10
1250527mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 16 (tone 32)
1250603mS R2DSP: PRIU DSP 3: read tone, port 0, channel 1, tone 0x0a
1250603mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 RX Fwd MFC: I.10 - "0"
1250604mS R2Channel: R2_ARG_9.1: EventTx: Dialling State: Dialling
1250604mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 TX Bwd MFC: A.1 - SendNextDigit
1250604mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 1 (tone 33)
1250604mS R2Line: line: 9.1: State= IncomingGuard RxMessage: ReceivedDigit
1250605mS R2Line: line: 9.1: Routing Digit Received 0
1250670mS R2DSP: PRIU DSP 3: read tone, port 0, channel 1, tone 0x10
1250670mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 16 (tone 32)
1250745mS R2DSP: PRIU DSP 3: read tone, port 0, channel 1, tone 0x0a
1250745mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 RX Fwd MFC: I.10 - "0"
1250746mS R2Channel: R2_ARG_9.1: EventTx: Dialling State: Dialling
1250746mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 TX Bwd MFC: A.1 - SendNextDigit
1250746mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 1 (tone 33)
1250746mS R2Line: line: 9.1: State= IncomingGuard RxMessage: ReceivedDigit
1250746mS R2Line: line: 9.1: Routing Digit Received 0
1250812mS R2DSP: PRIU DSP 3: read tone, port 0, channel 1, tone 0x10
1250812mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 16 (tone 32)
1265745mS R2Dialler: R2 Dialler: R2_ARG_9.1: State: Bwd 0 TX Bwd MFC: A.4 - Congestion
1265745mS R2DSP: PRIU DSP 3: channel 1 (timeslot 2), send digit 4 (tone 36)
1265745mS R2Dialler: R2_ARG_9.1: MFC State Change: Bwd 0 -> Idle
1265745mS R2Line: line: 9.1: State= IncomingGuard RxMessage: Disconnect
1266875mS R2DSP: PRIU DSP 3: is alive

Thanks in advance for your help.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top