Hi,
We expect some problem to register a D100 to a IPO 9.1.
I have see the last post about the problem... following the trace i have delete the D100.cfg, D100settings.txt and recreate it with 192.168.X.X/D100.cfg....
I have change the firware version on the file to match with the bin on my folder.
My IPO is set to manager file server with my PC to download bin files but the base flash green and reboot, flash green and reboot again...
there the last trace of the system log
[2000/01/01 00:01:17.196] Synchronization_main() : System Reset.
[2000/01/01 00:01:17.350] System goes down... (Use WatchDog timer for reset: 6)
[2000/01/01 00:00:00.359] 0000 HS9 EVENT_ENTER_TESTMODE
[2000/01/01 00:00:02.102] 0001 [NetStack Initialize] Stored IP address(192.168.150.25) assigned.
[000]RFC:Open DBC [slot:2]
[2000/01/01 00:00:12.103] 0002 Try to Connect Configuration Server...
[2000/01/01 00:00:12.222] 0003 [T] - Create HTTPD Thread[0] :32
[2000/01/01 00:00:12.223] 0004 [T] - Create HTTPD Thread[1] :31
[2000/01/01 00:00:12.223] 0005 [T] - Create HTTPD Thread[2] :30
[2000/01/01 00:00:12.224] 0006 [T] - Create HTTPD Thread[3] :29
[2000/01/01 00:00:12.225] 0007 [/D100.cfg] reading.
[2000/01/01 00:00:12.279] 0008 - finished.
[2000/01/01 00:00:12.281] 0009 [/D100prov.txt] reading.
[2000/01/01 00:00:27.239] 0010 [E] [/D100prov.txt] File Not Found.
[2000/01/01 00:00:27.240] 0011 [E] HTTP Client Return Error:-1
[2000/01/01 00:00:27.250] 0012 - OK. Provisioning file is not exists.
[2000/01/01 00:00:27.251] 0013 [/D100settings.txt] reading.
[2000/01/01 00:00:27.304] 0014 - finished.
[2000/01/01 00:00:27.305] 0015 [W] << ATTENTION>> [DIALING_PLAN] File is not defined in the config file.
[2000/01/01 00:00:27.344] *** Execute Firmware Update.
[2000/01/01 00:00:28.705] 0016 [E] HTTP Client Return Error:260
[2000/01/01 00:00:39.028] 0017 [T] === SW1 (Short Detect Mode) Pushed ! ===
[2000/01/01 00:00:41.028] 0018 [T] === SW1 Pushed ! ===
[2000/01/01 00:00:47.027] 0019 [W] KEEP ALIVE Timer failed. count : 0
[2000/01/01 00:00:51.028] 0020 [E] Synchronization_setRegistrationState() :Error - can't get SYNC_SEMAPHORE
[000]RFC:Open DBC [slot:5]
[2000/01/01 00:00:58.752] 0021 HS1 [PRESS] RADIO_DISC
[2000/01/01 00:01:22.101] 0022 [E] HTTP Client Return Error:260
[2000/01/01 00:01:27.108] *** Firmware Update Success. Reboot Base Station.
[2000/01/01 00:01:27.230] 0023 - succes.
[2000/01/01 00:01:27.231] Initialize D100 Base System Finish.
Firmware Version : D100_1.2.1_0.8.6
Hardware Version : 4
NV Version : 16
Firmware Side : 1 - 1
(Base Information)
Serial ID : SID:78E7D183877C1251729738D6
MAC Address : 00:E0:11:0B:1D:AC
RF ID : 01:85:84:70:68
CLOCK ADJUST : 11:03:04
BANDGAP ADJUST : MST-06, SLV-08
MARKET(0:GL/1:EU): 0
UserAgent(0100): 0
BootStrap(0:Normal): 0
Number of Regist : 1
(Handset Information)
LOGIN MAP : 0x00
REGISTRATION INFO:
[1] 0169d12997db0c1f95b7cb2c27207c5096abc3c2ab
[2] ffffffffffffffffffffffffffffffffffffffffff
[3] ffffffffffffffffffffffffffffffffffffffffff
[4] ffffffffffffffffffffffffffffffffffffffffff
[5] ffffffffffffffffffffffffffffffffffffffffff
[6] ffffffffffffffffffffffffffffffffffffffffff
[7] ffffffffffffffffffffffffffffffffffffffffff
[8] ffffffffffffffffffffffffffffffffffffffffff
USER INFO :
[1] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[2] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[3] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[4] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[5] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[6] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[7] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[8] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[2000/01/01 00:01:27.394] Synchronization_main() : System Reset.
[2000/01/01 00:01:27.544] System goes down... (Use WatchDog timer for reset: 6)
[2000/01/01 00:00:00.359] 0000 HS9 EVENT_ENTER_TESTMODE
[2000/01/01 00:00:02.102] 0001 [NetStack Initialize] Stored IP address(192.168.150.25) assigned.
[000]RFC:Open DBC [slot:2]
[000]RFC:Open DBC [slot:0]
[000]RFC:Open DBC [slot:10]
[2000/01/01 00:00:07.992] 0002 HS1 [PRESS] RADIO_DISC
[2000/01/01 00:00:12.103] 0003 Try to Connect Configuration Server...
[2000/01/01 00:00:12.223] 0004 [T] - Create HTTPD Thread[0] :32
[2000/01/01 00:00:12.225] 0005 [T] - Create HTTPD Thread[1] :31
[2000/01/01 00:00:12.225] 0006 [T] - Create HTTPD Thread[2] :30
[2000/01/01 00:00:12.226] 0007 [T] - Create HTTPD Thread[3] :29
[2000/01/01 00:00:12.227] 0008 [/D100.cfg] reading.
[2000/01/01 00:00:13.303] 0009 - finished.
[2000/01/01 00:00:13.304] 0010 [/D100prov.txt] reading.
[2000/01/01 00:00:28.316] 0011 [E] [/D100prov.txt] File Not Found.
[2000/01/01 00:00:28.317] 0012 [E] HTTP Client Return Error:-1
[2000/01/01 00:00:28.321] 0013 - OK. Provisioning file is not exists.
[2000/01/01 00:00:28.322] 0014 [/D100settings.txt] reading.
[2000/01/01 00:00:28.513] 0015 - finished.
[2000/01/01 00:00:28.514] 0016 [W] << ATTENTION>> [DIALING_PLAN] File is not defined in the config file.
[2000/01/01 00:00:28.553] *** Execute Firmware Update.
[2000/01/01 00:00:29.805] 0017 [E] HTTP Client Return Error:260
Thank you for your assistance. If someone have an idea please let me know !
We expect some problem to register a D100 to a IPO 9.1.
I have see the last post about the problem... following the trace i have delete the D100.cfg, D100settings.txt and recreate it with 192.168.X.X/D100.cfg....
I have change the firware version on the file to match with the bin on my folder.
My IPO is set to manager file server with my PC to download bin files but the base flash green and reboot, flash green and reboot again...
there the last trace of the system log
[2000/01/01 00:01:17.196] Synchronization_main() : System Reset.
[2000/01/01 00:01:17.350] System goes down... (Use WatchDog timer for reset: 6)
[2000/01/01 00:00:00.359] 0000 HS9 EVENT_ENTER_TESTMODE
[2000/01/01 00:00:02.102] 0001 [NetStack Initialize] Stored IP address(192.168.150.25) assigned.
[000]RFC:Open DBC [slot:2]
[2000/01/01 00:00:12.103] 0002 Try to Connect Configuration Server...
[2000/01/01 00:00:12.222] 0003 [T] - Create HTTPD Thread[0] :32
[2000/01/01 00:00:12.223] 0004 [T] - Create HTTPD Thread[1] :31
[2000/01/01 00:00:12.223] 0005 [T] - Create HTTPD Thread[2] :30
[2000/01/01 00:00:12.224] 0006 [T] - Create HTTPD Thread[3] :29
[2000/01/01 00:00:12.225] 0007 [/D100.cfg] reading.
[2000/01/01 00:00:12.279] 0008 - finished.
[2000/01/01 00:00:12.281] 0009 [/D100prov.txt] reading.
[2000/01/01 00:00:27.239] 0010 [E] [/D100prov.txt] File Not Found.
[2000/01/01 00:00:27.240] 0011 [E] HTTP Client Return Error:-1
[2000/01/01 00:00:27.250] 0012 - OK. Provisioning file is not exists.
[2000/01/01 00:00:27.251] 0013 [/D100settings.txt] reading.
[2000/01/01 00:00:27.304] 0014 - finished.
[2000/01/01 00:00:27.305] 0015 [W] << ATTENTION>> [DIALING_PLAN] File is not defined in the config file.
[2000/01/01 00:00:27.344] *** Execute Firmware Update.
[2000/01/01 00:00:28.705] 0016 [E] HTTP Client Return Error:260
[2000/01/01 00:00:39.028] 0017 [T] === SW1 (Short Detect Mode) Pushed ! ===
[2000/01/01 00:00:41.028] 0018 [T] === SW1 Pushed ! ===
[2000/01/01 00:00:47.027] 0019 [W] KEEP ALIVE Timer failed. count : 0
[2000/01/01 00:00:51.028] 0020 [E] Synchronization_setRegistrationState() :Error - can't get SYNC_SEMAPHORE
[000]RFC:Open DBC [slot:5]
[2000/01/01 00:00:58.752] 0021 HS1 [PRESS] RADIO_DISC
[2000/01/01 00:01:22.101] 0022 [E] HTTP Client Return Error:260
[2000/01/01 00:01:27.108] *** Firmware Update Success. Reboot Base Station.
[2000/01/01 00:01:27.230] 0023 - succes.
[2000/01/01 00:01:27.231] Initialize D100 Base System Finish.
Firmware Version : D100_1.2.1_0.8.6
Hardware Version : 4
NV Version : 16
Firmware Side : 1 - 1
(Base Information)
Serial ID : SID:78E7D183877C1251729738D6
MAC Address : 00:E0:11:0B:1D:AC
RF ID : 01:85:84:70:68
CLOCK ADJUST : 11:03:04
BANDGAP ADJUST : MST-06, SLV-08
MARKET(0:GL/1:EU): 0
UserAgent(0100): 0
BootStrap(0:Normal): 0
Number of Regist : 1
(Handset Information)
LOGIN MAP : 0x00
REGISTRATION INFO:
[1] 0169d12997db0c1f95b7cb2c27207c5096abc3c2ab
[2] ffffffffffffffffffffffffffffffffffffffffff
[3] ffffffffffffffffffffffffffffffffffffffffff
[4] ffffffffffffffffffffffffffffffffffffffffff
[5] ffffffffffffffffffffffffffffffffffffffffff
[6] ffffffffffffffffffffffffffffffffffffffffff
[7] ffffffffffffffffffffffffffffffffffffffffff
[8] ffffffffffffffffffffffffffffffffffffffffff
USER INFO :
[1] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[2] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[3] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[4] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[5] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[6] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[7] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[8] 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[2000/01/01 00:01:27.394] Synchronization_main() : System Reset.
[2000/01/01 00:01:27.544] System goes down... (Use WatchDog timer for reset: 6)
[2000/01/01 00:00:00.359] 0000 HS9 EVENT_ENTER_TESTMODE
[2000/01/01 00:00:02.102] 0001 [NetStack Initialize] Stored IP address(192.168.150.25) assigned.
[000]RFC:Open DBC [slot:2]
[000]RFC:Open DBC [slot:0]
[000]RFC:Open DBC [slot:10]
[2000/01/01 00:00:07.992] 0002 HS1 [PRESS] RADIO_DISC
[2000/01/01 00:00:12.103] 0003 Try to Connect Configuration Server...
[2000/01/01 00:00:12.223] 0004 [T] - Create HTTPD Thread[0] :32
[2000/01/01 00:00:12.225] 0005 [T] - Create HTTPD Thread[1] :31
[2000/01/01 00:00:12.225] 0006 [T] - Create HTTPD Thread[2] :30
[2000/01/01 00:00:12.226] 0007 [T] - Create HTTPD Thread[3] :29
[2000/01/01 00:00:12.227] 0008 [/D100.cfg] reading.
[2000/01/01 00:00:13.303] 0009 - finished.
[2000/01/01 00:00:13.304] 0010 [/D100prov.txt] reading.
[2000/01/01 00:00:28.316] 0011 [E] [/D100prov.txt] File Not Found.
[2000/01/01 00:00:28.317] 0012 [E] HTTP Client Return Error:-1
[2000/01/01 00:00:28.321] 0013 - OK. Provisioning file is not exists.
[2000/01/01 00:00:28.322] 0014 [/D100settings.txt] reading.
[2000/01/01 00:00:28.513] 0015 - finished.
[2000/01/01 00:00:28.514] 0016 [W] << ATTENTION>> [DIALING_PLAN] File is not defined in the config file.
[2000/01/01 00:00:28.553] *** Execute Firmware Update.
[2000/01/01 00:00:29.805] 0017 [E] HTTP Client Return Error:260
Thank you for your assistance. If someone have an idea please let me know !