There was almost working route.
<rocap:rou=5;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
5 0110000000000010 7 3110030011 0 30 128 00151515 111110100130 001100
END
<rodap:rou=5;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
5 SL60 H'00000310 H'15400000 H'06310000 NO
END
<ROEDP:ROU=5,TRU=ALL;
ROUTE EQUIPMENT DATA
ROU TRU EQU IP ADDRESS SQU INDDAT CNTRL
5 001-1 001-2-20-01 H'000000000000
5 001-2 001-2-20-02 H'000000000000
5 001-3 001-2-20-03 H'000000000000
5 001-4 001-2-20-04 H'000000000000
5 001-5 001-2-20-05 H'000000000000
5 001-6 001-2-20-06 H'000000000000
5 001-7 001-2-20-07 H'000000000000
5 001-8 001-2-20-08 H'000000000000
5 001-9 001-2-20-09 H'000000000000
5 001-10 001-2-20-10 H'000000000000
5 001-11 001-2-20-11 H'000000000000
5 001-12 001-2-20-12 H'000000000000
5 001-13 001-2-20-13 H'000000000000
5 001-14 001-2-20-14 H'000000000000
5 001-15 001-2-20-15 H'000000000000
5 001-16 001-2-20-17 H'000000000000
5 001-17 001-2-20-18 H'000000000000
5 001-18 001-2-20-19 H'000000000000
5 001-19 001-2-20-20 H'000000000000
5 001-20 001-2-20-21 H'000000000000
5 001-21 001-2-20-22 H'000000000000
5 001-22 001-2-20-23 H'000000000000
5 001-23 001-2-20-24 H'000000000000
5 001-24 001-2-20-25 H'000000000000
5 001-25 001-2-20-26 H'000000000000
5 001-26 001-2-20-27 H'000000000000
5 001-27 001-2-20-28 H'000000000000
5 001-28 001-2-20-29 H'000000000000
5 001-29 001-2-20-30 H'000000000000
5 001-30 001-2-20-31 H'000000000000
END
With one small problem.
The first timeslot at this route constantly was the being able BUSY in not dependence on anything.
Replacement of TLU76 didn't bring result.
<susip:rou=5,tru=all;
STATUS INFORMATION AT 14:24:34 15NOV17
ROU TRU TYPE TRAFFIC STATE/PTR LINE STATE/PTR ADD INFO
5 001-1 TL60 IDLE #0081 BUSY #0091
5 001-2 TL60 IDLE #0080 FREE #0090
5 001-3 TL60 IDLE #007F FREE #008F
5 001-4 TL60 IDLE #007E FREE #008E
5 001-5 TL60 IDLE #007D FREE #008D
5 001-6 TL60 IDLE #007C FREE #008C
5 001-7 TL60 IDLE #007B FREE #008B
5 001-8 TL60 IDLE #007A FREE #008A
5 001-9 TL60 IDLE #0079 FREE #0089
5 001-10 TL60 IDLE #0078 FREE #0088
5 001-11 TL60 IDLE #0077 FREE #0087
5 001-12 TL60 IDLE #0076 FREE #0086
5 001-13 TL60 IDLE #0075 FREE #0085
5 001-14 TL60 IDLE #0074 FREE #0084
5 001-15 TL60 IDLE #0073 FREE #0083
5 001-16 TL60 IDLE #0072 FREE #0082
5 001-17 TL60 IDLE #0071 FREE #0081
5 001-18 TL60 IDLE #0070 FREE #0080
5 001-19 TL60 IDLE #006F FREE #007F
5 001-20 TL60 IDLE #006E FREE #007E
5 001-21 TL60 IDLE #006D FREE #007D
5 001-22 TL60 IDLE #006C FREE #007C
5 001-23 TL60 IDLE #006B FREE #007B
5 001-24 TL60 IDLE #006A FREE #007A
5 001-25 TL60 IDLE #0069 FREE #0079
5 001-26 TL60 IDLE #0068 FREE #0078
5 001-27 TL60 IDLE #0067 FREE #0077
5 001-28 TL60 IDLE #0066 FREE #0076
5 001-29 TL60 IDLE #0065 FREE #0075
5 001-30 TL60 IDLE #0064 FREE #0074
END
To remove a timeslot of 1 route it wasn't possible to remove.
<ROEQE:ROU=5,TRU=1-1;
ROEQE:ROU=5,TRU=1-1;
SURE? (YES/NO)
<y;
NOT ACCEPTED
TRUNK IS BUSY
It was necessary to restore operability of a route having registered it with other number but in too time that there were no stream errors.
<sacos:unit=dcp,lim=1,filno=3,reloff=6,point=241,data=0;
SACOS:UNIT=DCP,LIM=1,FILNO=3,RELOFF=6,POINT=241,DATA=0;
SURE? (YES/NO)
<y;
WAIT
EXECUTED
<sacop:unit=dcp,lim=1,filno=3,reloff=6,point=240&&25f;
MEMORY CONTENT ON INDIVIDUAL POSITION
EXE A
FILE NUMBER RELOAD FILE START DS FILE START
3 00000635
POINT RELOFF DSOFF ADDRESS DATA ISO
0240 0006 00002A3B 02 .
0241 0006 00002A4B 00 .
0242 0006 00002A5B 01 .
0243 0006 00002A6B 01 .
0244 0006 00002A7B 01 .
0245 0006 00002A8B 01 .
0246 0006 00002A9B 01 .
0247 0006 00002AAB 01 .
0248 0006 00002ABB 01 .
0249 0006 00002ACB 01 .
024A 0006 00002ADB 01 .
024B 0006 00002AEB 01 .
024C 0006 00002AFB 01 .
024D 0006 00002B0B 01 .
024E 0006 00002B1B 01 .
024F 0006 00002B2B 01 .
0250 0006 00002B3B 01 .
0251 0006 00002B4B 01 .
0252 0006 00002B5B 01 .
0253 0006 00002B6B 01 .
0254 0006 00002B7B 01 .
0255 0006 00002B8B 01 .
0256 0006 00002B9B 01 .
0257 0006 00002BAB 01 .
0258 0006 00002BBB 01 .
0259 0006 00002BCB 01 .
025A 0006 00002BDB 01 .
025B 0006 00002BEB 01 .
025C 0006 00002BFB 01 .
025D 0006 00002C0B 01 .
025E 0006 00002C1B 01 .
025F 0006 00002C2B 01 .
END
<sacos:unit=dcp,lim=1,filno=3,reloff=6,point=241,data=1;
SACOS:UNIT=DCP,LIM=1,FILNO=3,RELOFF=6,POINT=241,DATA=1;
SURE? (YES/NO)
<y;
WAIT
EXECUTED
<allop;
ALARM LOG
IDENTITY:
VERSION: CXP1010139/4/TSW-SP08/R9A
DATE: 15NOV17 TIME: 16:37:36
CLASS: 4
269 DIGITAL TRUNK, LOSS OF FRAME SYNCHRONIZATION
DATE TIME ALP NOIF UNIT EQU BRDID INF1
15NOV17 16:30:51 2 1 SLP60 001-2-20-00 57 260
CLASS: 3
312 DIGITAL TRUNK, LOSS OF SIGNAL
DATE TIME ALP NOIF UNIT EQU BRDID INF1
15NOV17 16:30:51 1 1 SLP60 001-2-20-00 57 260
CLASS: 2
303 DATA LINK ALARM
DATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
15NOV17 16:30:54 3 1 SLP60 001-2-20-00 57 260 0
LAST ALREI: 15NOV17, 16:30:51
END
<ROEQE:ROU=5,TRU=1-1;
ROEQE:ROU=5,TRU=1-1;
SURE? (YES/NO)
<y;
NOT ACCEPTED
TRUNK IS BUSY
<cnboe:bpos=1-2-20;
CONFIGURATION BOARD END
INDIVIDUAL STILL INITIATED ON EQU 1-2-20-00
END
<sacos:unit=dcp,lim=1,filno=3,reloff=6,point=240,data=1;
SACOS:UNIT=DCP,LIM=1,FILNO=3,RELOFF=6,POINT=240,DATA=1;
SURE? (YES/NO)
<y;
WAIT
EXECUTED
<ROEQE:ROU=5,TRU=1-1;
ROEQE:ROU=5,TRU=1-1;
SURE? (YES/NO)
<y;
NOT ACCEPTED
TRUNK IS BUSY
<cnboe:bpos=1-2-20;
EXECUTED
The new route is created, the payment is established in a new position, everything is registered and works. The station doesn't give error messages.
It is necessary only to remove a mention of a route with number five and an unextracted timeslot position 1-2-20.
<ROEQE:ROU=5,TRU=1-1;
ROEQE:ROU=5,TRU=1-1;
SURE? (YES/NO)
<y;
NOT ACCEPTED
TRUNK IS BUSY
<route:rou=5;
NOT ACCEPTED
TRUNKS EXIST IN THIS ROUTE
<susip:rou=5,tru=all;
STATUS INFORMATION AT 21:57:54 15NOV17
ROU TRU TYPE TRAFFIC STATE/PTR LINE STATE/PTR ADD INFO
5 001-1 TL60 IDLE #0081 BLOCKED #0091
END
Maybe there will be a clever person and will prompt the place of storage of these data with the purpose of their removal through SACOS?
<rocap:rou=5;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
5 0110000000000010 7 3110030011 0 30 128 00151515 111110100130 001100
END
<rodap:rou=5;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
5 SL60 H'00000310 H'15400000 H'06310000 NO
END
<ROEDP:ROU=5,TRU=ALL;
ROUTE EQUIPMENT DATA
ROU TRU EQU IP ADDRESS SQU INDDAT CNTRL
5 001-1 001-2-20-01 H'000000000000
5 001-2 001-2-20-02 H'000000000000
5 001-3 001-2-20-03 H'000000000000
5 001-4 001-2-20-04 H'000000000000
5 001-5 001-2-20-05 H'000000000000
5 001-6 001-2-20-06 H'000000000000
5 001-7 001-2-20-07 H'000000000000
5 001-8 001-2-20-08 H'000000000000
5 001-9 001-2-20-09 H'000000000000
5 001-10 001-2-20-10 H'000000000000
5 001-11 001-2-20-11 H'000000000000
5 001-12 001-2-20-12 H'000000000000
5 001-13 001-2-20-13 H'000000000000
5 001-14 001-2-20-14 H'000000000000
5 001-15 001-2-20-15 H'000000000000
5 001-16 001-2-20-17 H'000000000000
5 001-17 001-2-20-18 H'000000000000
5 001-18 001-2-20-19 H'000000000000
5 001-19 001-2-20-20 H'000000000000
5 001-20 001-2-20-21 H'000000000000
5 001-21 001-2-20-22 H'000000000000
5 001-22 001-2-20-23 H'000000000000
5 001-23 001-2-20-24 H'000000000000
5 001-24 001-2-20-25 H'000000000000
5 001-25 001-2-20-26 H'000000000000
5 001-26 001-2-20-27 H'000000000000
5 001-27 001-2-20-28 H'000000000000
5 001-28 001-2-20-29 H'000000000000
5 001-29 001-2-20-30 H'000000000000
5 001-30 001-2-20-31 H'000000000000
END
With one small problem.
The first timeslot at this route constantly was the being able BUSY in not dependence on anything.
Replacement of TLU76 didn't bring result.
<susip:rou=5,tru=all;
STATUS INFORMATION AT 14:24:34 15NOV17
ROU TRU TYPE TRAFFIC STATE/PTR LINE STATE/PTR ADD INFO
5 001-1 TL60 IDLE #0081 BUSY #0091
5 001-2 TL60 IDLE #0080 FREE #0090
5 001-3 TL60 IDLE #007F FREE #008F
5 001-4 TL60 IDLE #007E FREE #008E
5 001-5 TL60 IDLE #007D FREE #008D
5 001-6 TL60 IDLE #007C FREE #008C
5 001-7 TL60 IDLE #007B FREE #008B
5 001-8 TL60 IDLE #007A FREE #008A
5 001-9 TL60 IDLE #0079 FREE #0089
5 001-10 TL60 IDLE #0078 FREE #0088
5 001-11 TL60 IDLE #0077 FREE #0087
5 001-12 TL60 IDLE #0076 FREE #0086
5 001-13 TL60 IDLE #0075 FREE #0085
5 001-14 TL60 IDLE #0074 FREE #0084
5 001-15 TL60 IDLE #0073 FREE #0083
5 001-16 TL60 IDLE #0072 FREE #0082
5 001-17 TL60 IDLE #0071 FREE #0081
5 001-18 TL60 IDLE #0070 FREE #0080
5 001-19 TL60 IDLE #006F FREE #007F
5 001-20 TL60 IDLE #006E FREE #007E
5 001-21 TL60 IDLE #006D FREE #007D
5 001-22 TL60 IDLE #006C FREE #007C
5 001-23 TL60 IDLE #006B FREE #007B
5 001-24 TL60 IDLE #006A FREE #007A
5 001-25 TL60 IDLE #0069 FREE #0079
5 001-26 TL60 IDLE #0068 FREE #0078
5 001-27 TL60 IDLE #0067 FREE #0077
5 001-28 TL60 IDLE #0066 FREE #0076
5 001-29 TL60 IDLE #0065 FREE #0075
5 001-30 TL60 IDLE #0064 FREE #0074
END
To remove a timeslot of 1 route it wasn't possible to remove.
<ROEQE:ROU=5,TRU=1-1;
ROEQE:ROU=5,TRU=1-1;
SURE? (YES/NO)
<y;
NOT ACCEPTED
TRUNK IS BUSY
It was necessary to restore operability of a route having registered it with other number but in too time that there were no stream errors.
<sacos:unit=dcp,lim=1,filno=3,reloff=6,point=241,data=0;
SACOS:UNIT=DCP,LIM=1,FILNO=3,RELOFF=6,POINT=241,DATA=0;
SURE? (YES/NO)
<y;
WAIT
EXECUTED
<sacop:unit=dcp,lim=1,filno=3,reloff=6,point=240&&25f;
MEMORY CONTENT ON INDIVIDUAL POSITION
EXE A
FILE NUMBER RELOAD FILE START DS FILE START
3 00000635
POINT RELOFF DSOFF ADDRESS DATA ISO
0240 0006 00002A3B 02 .
0241 0006 00002A4B 00 .
0242 0006 00002A5B 01 .
0243 0006 00002A6B 01 .
0244 0006 00002A7B 01 .
0245 0006 00002A8B 01 .
0246 0006 00002A9B 01 .
0247 0006 00002AAB 01 .
0248 0006 00002ABB 01 .
0249 0006 00002ACB 01 .
024A 0006 00002ADB 01 .
024B 0006 00002AEB 01 .
024C 0006 00002AFB 01 .
024D 0006 00002B0B 01 .
024E 0006 00002B1B 01 .
024F 0006 00002B2B 01 .
0250 0006 00002B3B 01 .
0251 0006 00002B4B 01 .
0252 0006 00002B5B 01 .
0253 0006 00002B6B 01 .
0254 0006 00002B7B 01 .
0255 0006 00002B8B 01 .
0256 0006 00002B9B 01 .
0257 0006 00002BAB 01 .
0258 0006 00002BBB 01 .
0259 0006 00002BCB 01 .
025A 0006 00002BDB 01 .
025B 0006 00002BEB 01 .
025C 0006 00002BFB 01 .
025D 0006 00002C0B 01 .
025E 0006 00002C1B 01 .
025F 0006 00002C2B 01 .
END
<sacos:unit=dcp,lim=1,filno=3,reloff=6,point=241,data=1;
SACOS:UNIT=DCP,LIM=1,FILNO=3,RELOFF=6,POINT=241,DATA=1;
SURE? (YES/NO)
<y;
WAIT
EXECUTED
<allop;
ALARM LOG
IDENTITY:
VERSION: CXP1010139/4/TSW-SP08/R9A
DATE: 15NOV17 TIME: 16:37:36
CLASS: 4
269 DIGITAL TRUNK, LOSS OF FRAME SYNCHRONIZATION
DATE TIME ALP NOIF UNIT EQU BRDID INF1
15NOV17 16:30:51 2 1 SLP60 001-2-20-00 57 260
CLASS: 3
312 DIGITAL TRUNK, LOSS OF SIGNAL
DATE TIME ALP NOIF UNIT EQU BRDID INF1
15NOV17 16:30:51 1 1 SLP60 001-2-20-00 57 260
CLASS: 2
303 DATA LINK ALARM
DATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
15NOV17 16:30:54 3 1 SLP60 001-2-20-00 57 260 0
LAST ALREI: 15NOV17, 16:30:51
END
<ROEQE:ROU=5,TRU=1-1;
ROEQE:ROU=5,TRU=1-1;
SURE? (YES/NO)
<y;
NOT ACCEPTED
TRUNK IS BUSY
<cnboe:bpos=1-2-20;
CONFIGURATION BOARD END
INDIVIDUAL STILL INITIATED ON EQU 1-2-20-00
END
<sacos:unit=dcp,lim=1,filno=3,reloff=6,point=240,data=1;
SACOS:UNIT=DCP,LIM=1,FILNO=3,RELOFF=6,POINT=240,DATA=1;
SURE? (YES/NO)
<y;
WAIT
EXECUTED
<ROEQE:ROU=5,TRU=1-1;
ROEQE:ROU=5,TRU=1-1;
SURE? (YES/NO)
<y;
NOT ACCEPTED
TRUNK IS BUSY
<cnboe:bpos=1-2-20;
EXECUTED
The new route is created, the payment is established in a new position, everything is registered and works. The station doesn't give error messages.
It is necessary only to remove a mention of a route with number five and an unextracted timeslot position 1-2-20.
<ROEQE:ROU=5,TRU=1-1;
ROEQE:ROU=5,TRU=1-1;
SURE? (YES/NO)
<y;
NOT ACCEPTED
TRUNK IS BUSY
<route:rou=5;
NOT ACCEPTED
TRUNKS EXIST IN THIS ROUTE
<susip:rou=5,tru=all;
STATUS INFORMATION AT 21:57:54 15NOV17
ROU TRU TYPE TRAFFIC STATE/PTR LINE STATE/PTR ADD INFO
5 001-1 TL60 IDLE #0081 BLOCKED #0091
END
Maybe there will be a clever person and will prompt the place of storage of these data with the purpose of their removal through SACOS?