Problem Dialing from PBX long Distance.

[dhunterpr]

Hi;

I want to provide access to some DN to the Domican Republic area code 809. I have added in my NPA the entry 1809 with RLI 7. The phone I whant to give access has setup NCOS 7. When I dial a phone like 1-809-221-XXXX I get a recording telling me the number cannot be complete as dialed, please check the number and dial again 131P. I talked to my long distance carrier and they tell me everything on their side is ok.

I checked the SPN and no entry for the 1809 exist. Also checked the NXX and there was an entry for the 809 I removed it (same result with or without it).

Also tried with the CLS TLD and UNR with the same result.

A copy of the DN follows, this is an Option 61 Rel 25;

DES 227
TN 012 0 03 15
TYPE 2616
CDEN 8D
CUST 0
AOM 0
FDN 5900
TGAR 1
LDN NO
NCOS 7
SGRP 0
RNPG 0
SCI 0
SSU
LNRS 16
XLST
CLS CTD FBD WTA LPR MTD FNA HTA TDD HFA
MWA LMPN RMMD SMWD AAD IMD DOS XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD CCSD SWD LNA CNDA
CFTD SFD DDV CNID CDCA MSID DAPA BFED RCBD
ICDD CDMD MCTD CLBD AUTU
GPUD DPUD DNDD CFXD ARHD CNTD CLTD ASCD
CPFA CPTA ABDD CFHD FICD NAID BUZZ AHD
DDGA NAMA
USRD ULAD RTDD RBDD RBHD PGND OCBD FLXD FTTC
CPND_LANG ENG
RCO 0
HUNT 5900
LHK 9
PLEV 02
AST 00 08
IAPG 1
AACS NO
ITNA NO
DGRP
PRI 01
DNDR 0
KEY 00 ACD 4055 0 2002
SPV
01 NRD
02 MSB
03 DWC 4055
04
05 MWK 5900
06
07
08 SCR 5699 0 MARP

 

[PERRYPJ]

BYPASS THE NARS, DIAL THE ACOD OF THAT ROUTE AND DIAL THE SAME NUMBER AND SEE IF YOU GET A RECORDING. IF SO ONCE AGAIN YOUR VENDOR HAS LIED TO YOU.

OLD ROLMEN WORKING ON NORTELS

 

[dhunterpr]

Perrypj;

I am newbie on Nortel how can I;

BYPASS THE NARS?

DIAL THE ACOD OF THAT ROUTE AND DIAL THE SAME NUMBER?

Thanks

 

[PERRYPJ]

PRINT THE RDB OF THE ROUTE, LOOK FOR THE ACOD. THERE IS A NUMBER BESIDE IT, SET YOUR PHONE FOR UNR IN THE CLS AND THEN DIAL THAT ACOD NUMBER FOLLOWED BY YOUR TELEPHONE NUMBER

OLD ROLMEN WORKING ON NORTELS

 

[dhunterpr]

I followed your instructions and I used both of the routes and the called was completed successfully, any recomendations on how to fix this issue ( of course beside changing the PBX programmer )

Thanks.

 

[BigBenjaBear]

Print the NPA in LD90 and its associated RLI. MAke sure that you have no DMI table set in the Route List Index

 

[dhunterpr]

I printed the RLI and there is no association to DMI is set to 0.