Hello,
We have a Nortel Option 81 CS1000 PBX with a PRI trunk group that is connected to our Asterisk Free PBX system. We have it setup on the Free PBX to send all calls that are dialed as "9+1+NPA+1234567" to our Nortel PBX over the Virtual PRI trunk group sending "9+1+NPA+1234567". The DCH messaging on the Nortel shows "9+1+NPA+1234567", but the Nortel is stripping all but the last four digits from the terminating number (4567). This causes an issue as we have extension 4567 programmed within the PBX and the calls will ring to that extension. This is an example of numerous cases where the last four digits seem to be remaining on these types of inbound calls to the Nortel from the Asterisk PBX. You can place calls fine from Nortel using "9+1+NPA+1234567". There is no IDC happening within the RDB that supports the PRI trunk group. I have been working days and days on this and cannot seem to figure this out. I would greatly appreciate any assistance.
TYPE RDB
CUST 00
ROUT 26
DES VIRTUAL
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 1234
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DEXT NO
DNAM NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
PAGE 002
SFB 3
NBS 2048
NBL 4096
IENB 5
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST NO
QREC NO
OAL NO
OTL NO
CDRX NO
VRAT NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO
TN 008 01
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 26 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA HPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE 1 MAR 2013
We have a Nortel Option 81 CS1000 PBX with a PRI trunk group that is connected to our Asterisk Free PBX system. We have it setup on the Free PBX to send all calls that are dialed as "9+1+NPA+1234567" to our Nortel PBX over the Virtual PRI trunk group sending "9+1+NPA+1234567". The DCH messaging on the Nortel shows "9+1+NPA+1234567", but the Nortel is stripping all but the last four digits from the terminating number (4567). This causes an issue as we have extension 4567 programmed within the PBX and the calls will ring to that extension. This is an example of numerous cases where the last four digits seem to be remaining on these types of inbound calls to the Nortel from the Asterisk PBX. You can place calls fine from Nortel using "9+1+NPA+1234567". There is no IDC happening within the RDB that supports the PRI trunk group. I have been working days and days on this and cannot seem to figure this out. I would greatly appreciate any assistance.
TYPE RDB
CUST 00
ROUT 26
DES VIRTUAL
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 1234
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DEXT NO
DNAM NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
PAGE 002
SFB 3
NBS 2048
NBL 4096
IENB 5
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST NO
QREC NO
OAL NO
OTL NO
CDRX NO
VRAT NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO
TN 008 01
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 26 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA HPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE 1 MAR 2013
