Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Point to point PRI programming

Status
Not open for further replies.

srcvh1

Technical User
Feb 1, 2007
156
US
Having troubles getting circuit to come up between to option 11s. You would think this would be pretty basic. At first the circuit came up and I was able to make test calls no problem. Then it dropped and kept dropping sporadically. The slips were all over the place. The far end doesn't have a CSU but the Main does (basic Adtran). I have replaced both cards on each end and replaced the CSU with no luck. The span is now permanently in Red alarm on both ends. Before I go to the carrier I want to confirm programming here to the masses. This also should be pretty basic but I want to cover all bases before battling the carrier. Any help or ideas would be appreciated, thanks!

Anyway, here is the programming for both sites:

SITE A MAIN

REQ prt
TYPE adan dch 6

ADAN DCH 6
CTYP DCHI
CARD 01
PORT 1
DES BATH
USR PRI
DCHL 1
OTBF 32
DRAT 56K
CLOK EXT
NASA NO
IFC SL1
SIDE NET
SEMT 1
CNEG 1
RLS ID 24
RCAP ND2 MSDL
MBGA NO
OVLR NO
OVLS NO
T23 20
T200 3
T203 10
N200 3
N201 260
K 7

REQ ****
OVL000
>ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 1

TYPE RDB
CUST 00
DMOD
ROUT 1
DES BATH
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC SL1
PNI 00001
NCNA YES
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 7901
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO

SITE B REMOTE

REQ prt
TYPE adan dch 5

ADAN DCH 5
CTYP DCHI
CARD 01
PORT 1
DES BATH
USR PRI
DCHL 1
OTBF 16
DRAT 56K
CLOK EXT
NASA NO
IFC SL1
SIDE USR
CNEG 1
RLS ID 24
RCAP ND2
MBGA NO
OVLR NO
OVLS NO
T23 20
T200 3
T203 10
N200 3
N201 260
K 7

REQ ****
OVL000
>ld 21
PT1000


REQ: prt
TYPE: rdb
CUST 0
ROUT 1

TYPE RDB
CUST 00
DMOD
ROUT 1
DES
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO YES
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 7901
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 3200
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6


PAGE 002

DRNG NO
CDR NO
VRAT NO
MUS NO
EQAR NO
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

REQ:
 
The DRAT should be 64KC for a PRI for a full 64K, clear channel signaling.
 
Red alarm at both ends means you have no carrier. Probably a wiring issue or the Telco has done something to the circuit.

It's a phone system, NOT a clock!
 
Thanks for the input guys. As it turns out it was a wiring issue. The problem was on the extended smartjack wiring, thank you Verizon!!

I just wanted to make sure my programming was good before the finger pointing started.

Thanks again!
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top