Poblem of G450 registration

[Madil]

Hello,
I have a CM rel 6.1 on an HP server with two G450 and one S8300D as an LSP. My problem is the first G450 with the LSP register only for one or two hour on the main CM, then it go to the LSP. The second G450 Stays on the main.
They have the same paremeters:
G450-001(super)# show interface

Vlan 1 is up, line protocol is up
Physical address is b4:b0:17:91:38:d8
Internet address is 172.116.50.135, mask is 255.255.0.0
Primary management interface
MTU 1500 bytes, Bandwidth 100000 kbit
IPSec PMTU: copy df-bit, Min PMTU is 300
Reliability 255/255 txLoad 1/255 rxLoad 1/255
Encapsulation ARPA, ICC-VLAN
Link status trap disabled
Full-duplex, 100Mb/s
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, Last output 00:00:00
Last clearing of 'show interface' counters never
5 minute input rate 643 bits/sec, 1 packets/sec
5 minute output rate 227 bits/sec, 0 packets/sec
0 input drops, 0 output drops, 0 unknown protocols
1613 packets input, 111375 bytes
1384 broadcasts received, 0 giants
0 input errors, 0 CRC
328 packets output, 30462 bytes
0 output errors, 0 collisions



G450-001(super)# show mgc

CALL CONTROLLER STATUS
-------------------------------------------
Registered : YES
Active Controller : 172.116.50.131
Controller SW Version : R016x.00.1.510.1
H248 Link Status : UP
H248 Link Error Code : 0x0

CONFIGURED MGC HOST
---------------------
172.116.50.111
172.116.50.131
-- Not Available --
-- Not Available --
sls disabled

Done!





G450-001(super)# show sys
System Name :
System Location :
System Contact :
Uptime (d,h:m:s) : 0,00:26:10
Call Controller Time : 14:46:00 14 NOV 2011
Serial No : 11N522784886
Model : G450
HW Ready for FIPS : No
Chassis HW Vintage : 1
Chassis HW Suffix : A
Mainboard HW Vintage : 2
Mainboard HW Suffix : B
Mainboard FW Vintage : 30.12.1
LAN MAC Address : b4:b0:17:91:38:d8
WAN1 MAC Address : b4:b0:17:91:38:d9
WAN2 MAC Address : b4:b0:17:91:38:da
SERVICES MAC address : b4:b0:17:91:38:db
Memory #1 : 256MB
Memory #2 : Not present
Compact Flash Memory : CompactFlash card is disabled
PSU #1 : 400W
PSU #2 : Not present
Media Socket #1 : MP80 VoIP DSP Module
Media Socket #2 : MP80 VoIP DSP Module
Media Socket #3 : Not present
Media Socket #4 : Not present
FAN Tray : Present



G450-001(super)# show recovery

RECOVERY TIMES
--------------------------------
Primary Search : 1
Total Search : 30
Transition Point: 2



G450-001(super)# show startup-config

! version 30.12.1
ds-mode t1
Config info release 30.12.1 time "11:09:28 11 NOV 2011 " serial_number 11N522784500
encrypted-username LPMQ9LgDIxPA42n2FxZfFQ== password 1vCPIoAyYw9Tqxoy+Ynodg+OHqKMYROvCWys1V+Nrc4= access-type d1kjnLNz/I6gZwl00TdiEA==
set logging file enable
set logging file condition all Error
set logging file condition BOOT Debug
no ip telnet
no snmp-server community
set port negotiation 10/5 disable
set port speed 10/5 100MB
interface Vlan 1
icc-vlan
ip address 172.116.50.135 255.255.0.0
pmG450-001(super)# i
exit
interface FastEthernet 10/3
exit
interface FastEthernet 10/4
exit
interface Console
exit
interface USB-Modem
description "Default Modem Setup"
timeout absolute 10
ppp authentication ras
no shutdown
ip address 10.3.248.253 255.255.255.252
exit
ip default-gateway 172.116.50.1 1 low
set mgc list 172.116.50.111,172.116.50.131
set mediaserver 172.116.50.111 172.116.50.111 23 telnet
set mediaserver 172.116.50.111 172.116.50.111 5023 sat
set mediaserver 172.116.50.131 172.116.50.131 23 telnet
set mediaserver 172.116.50.131 172.116.50.131 5023 sat
set reset-times transition-point 2
rtp-stat qos-trap
no rtp-stat fault
!#
!# End of configuration file. Press Enter to continue.


THANK YOU

 

[simreal]

Have your network team make sure your QoS settings are causing a problem. Also make sure the network ports are configured 100FULL like your gateway.

Also run the command "show faults" from the gateway while its in stand-alone" mode. Look for any indicator as to why it might be registered to the LSP.




- Miguel

A very wise and well respected man once told me "Shut Up!".

 

[avayasmith]

your transition point is set to 2, it should be set to 1......

i prefer clarity to agreement - dennis prager