Hello guys,
i am hoping you are all doing just fine.
I am experiencing a problem with my integration of the two.
I have an E1 from a Telco plugged into Port-1 of the Digium 1TE235BF & Port-2 of the Digium 1TE235BF is connected to the PRI30 card on the Panasonic.
On the FreePBX, the dial plan is as below;
X. ---> to the PSTN through Span-1
Asterisk to Panasonic ,1XX, 2XX, 3XX, 4XX & 5XX ---> towards KX-TDA200 through Span-2
Panasonic to Asterisk is, Press 9 get dial tone then dial 11XX (Automatic Route Selection, ARS setup in KX-TDA200)
i.e Extensions on the Asterisk are 11XX
Span 1 is set as;
Group 0
Switchtype : EuroISDN
Signaling : PRI-CPE
Coding : HDB3
Framing : CCS
Clock source : 0
Span-2 is set as;
Group 1
Switchtype : PRI-NET
Signaling : Q.SIG
Coding : HDB3
Framing : CCS
Clock source : 1
Setting on Panasonic KX-TDA200 is;
Program 1.Configuration -> 1.Slot -> PRI30 Port property, i set Port Type to QSIG-Slave.
CRC4 is Enabled. Outbound calls to PSTN from FreePBX work fine. However calls to Panasonic from FreePBX and calls to FreePBX from Panasonic are not working just yet.
Also i configured incoming calls from the PSTN through SPAN-1 to be forwarded to Trunk (SPAN-2 -> TO KX-TDA200.
Incoming calls through Span-1 gets a message "The number you have dialed is not in service , please check the number and dial again" from asterisk.
Any idea on what i could be missing?.
Will be grateful for some helpful responses
NOTE: Call to PSTN from Panasonic, do not go out. Dialing is Press 9, get dial tone then number (Instead get response from Asterisk)
i am hoping you are all doing just fine.
I am experiencing a problem with my integration of the two.
I have an E1 from a Telco plugged into Port-1 of the Digium 1TE235BF & Port-2 of the Digium 1TE235BF is connected to the PRI30 card on the Panasonic.
On the FreePBX, the dial plan is as below;
X. ---> to the PSTN through Span-1
Asterisk to Panasonic ,1XX, 2XX, 3XX, 4XX & 5XX ---> towards KX-TDA200 through Span-2
Panasonic to Asterisk is, Press 9 get dial tone then dial 11XX (Automatic Route Selection, ARS setup in KX-TDA200)
i.e Extensions on the Asterisk are 11XX
Span 1 is set as;
Group 0
Switchtype : EuroISDN
Signaling : PRI-CPE
Coding : HDB3
Framing : CCS
Clock source : 0
Span-2 is set as;
Group 1
Switchtype : PRI-NET
Signaling : Q.SIG
Coding : HDB3
Framing : CCS
Clock source : 1
Setting on Panasonic KX-TDA200 is;
Program 1.Configuration -> 1.Slot -> PRI30 Port property, i set Port Type to QSIG-Slave.
CRC4 is Enabled. Outbound calls to PSTN from FreePBX work fine. However calls to Panasonic from FreePBX and calls to FreePBX from Panasonic are not working just yet.
Also i configured incoming calls from the PSTN through SPAN-1 to be forwarded to Trunk (SPAN-2 -> TO KX-TDA200.
Incoming calls through Span-1 gets a message "The number you have dialed is not in service , please check the number and dial again" from asterisk.
Any idea on what i could be missing?.
Will be grateful for some helpful responses
NOTE: Call to PSTN from Panasonic, do not go out. Dialing is Press 9, get dial tone then number (Instead get response from Asterisk)