Paging Systems question

[mlas]

Hi hope someone can help.

We have a CS1000M (OPT61) running 4.5s/w. We need to connect a paging system to the pabx. Can a MIRAN card act as an interface for this? If not what other hardware woudl I require?

Thanks for your responses.

Regards

M

 

[bigindian65]

No on the MIRAN. Univ. Trunk card. and a paging system.

Mato' Was'aka

 

[EddieDuece]

Here is what my paging rout looks like;
CUST 00
ROUT 5
DES PAGING
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
ICOG OGT
RANX NO
SRCH LIN
STEP
ACOD 74
CPP NO
TARG 01 02 04 06
CLEN 1
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
OOD 1
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512

IENB 5
TFD 0
LEXT 100
VGD 6
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
CDR NO
MUS NO
MR NO
RACD NO


PAGE 006

MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

Trunk Member;
CUST 0
ROUT 5

TYPE TLST
TKTP COT
ROUT 5
DES PAGING
TN 012 0 01 05 MBER 1 PAGING

Trunk;
DES PAGING
TN 012 0 01 05
TYPE COT
CDEN 8D
CUST 0
XTRK EXUT
FWTM NO
TIMP 600
BIMP 3COM
AUTO_BIMP NO
TRK ANLG
NCOS 0
RTMB 5 1
NITE
SIGL LOP
SUPN NO
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD
P10 NTC
TKID
AACR NO
DATE NO DATE

 

[johnpoole]

and past the trunk card you will need a paging adapter.. best bet is valcom for that item...

john poole
bellsouth business
columbia,sc

 

[pronei]

Only if you are doing station level paging will you need a paging adapter. Trunk level paging pipes straight into a paging amp, no adapter required.

 

[acewarlock]

pronei: What do you mean by Station level paging?




This is a Signature and not part of the answer, it appears on every reply.

This is an Analogy so don't take it personally as some have.

Why change the engine if all you need is to change the spark plugs.

 

[mlas]

Thanks for all your help guys, much appreciated.

 

[pronei]

Station level = when dialing an analog (2500) set that is directly connected to a valcom paging adapter and then connected to paging amp. This method allows you to use your analog station card and analog ism's for paging. This method also works well if you want to page over IP and you have a Quintum Tenor or Audio Codes box connected via SIP or H323 on the far end.

Trunk level = when dialing the acod of an PAG route that has a trunk built on a XUT and directly connected to a paging amp. This method does not cost any ism's but does cost a XUT port.

I currently use both methods of paging. If you want details of config for either scenario I'd be happy to post.