I have a page trunk port set up on a CS1000.
When I dial my page access code, I speak my page then disconnect. The page is heard over the speakers, but then a busy tone is heard over the speakers.
Below is my RDB and member TNB
TYPE RDB
CUST 00
ROUT 1
DES PAGING
TKTP WAT
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK NO
ISDN NO
PTYP ACO
CNDP UKWN
AUTO NO
DNIS NO
ICOG OGT
SRCH LIN
STEP
ACOD 5976
CPP NO
TARG
CLEN 1
OABS
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
OOD 1
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
IENB 5
TFD 0
LEXT 100
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
CDR NO
MUS NO
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
PAGE 002
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
AACR NO
*********************************************
DES PAGE
TN 000 0 03 06 VIRTUAL
TYPE WAT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 600
TRK ANLG
NCOS 0
RTMB 1 1
NITE
SIGL LOP
SUPN NO
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD SPCD
P10 NTC
TKID
AACR NO
DATE 19 MAR 2020
**********************************************
From the paging amplifier, the signal must be 600 ohms, and the paging module needs to receive DTMF tones utilizing an OPEN LOOP TRUNK PORT.
I have changed SUPN to YES and set STYP to BST and PIP, but then I just get busy when dialing ACOD
Would anyone know why on hangup the busy tones would be coming through?
When I dial my page access code, I speak my page then disconnect. The page is heard over the speakers, but then a busy tone is heard over the speakers.
Below is my RDB and member TNB
TYPE RDB
CUST 00
ROUT 1
DES PAGING
TKTP WAT
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK NO
ISDN NO
PTYP ACO
CNDP UKWN
AUTO NO
DNIS NO
ICOG OGT
SRCH LIN
STEP
ACOD 5976
CPP NO
TARG
CLEN 1
OABS
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
OOD 1
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
IENB 5
TFD 0
LEXT 100
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
CDR NO
MUS NO
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
PAGE 002
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
AACR NO
*********************************************
DES PAGE
TN 000 0 03 06 VIRTUAL
TYPE WAT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 600
TRK ANLG
NCOS 0
RTMB 1 1
NITE
SIGL LOP
SUPN NO
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD SPCD
P10 NTC
TKID
AACR NO
DATE 19 MAR 2020
**********************************************
From the paging amplifier, the signal must be 600 ohms, and the paging module needs to receive DTMF tones utilizing an OPEN LOOP TRUNK PORT.
I have changed SUPN to YES and set STYP to BST and PIP, but then I just get busy when dialing ACOD
Would anyone know why on hangup the busy tones would be coming through?
