Outward Transfer

[nhlanhla]

Good day

I have a HIPATH 4000 system that i currently linked to a small PBX using one of its analogue extensions
The ATA is coming in as an analogue trunk, i Therefore seek assistance if its possible to Transfer calls to the using that same trunk.

Regards

 

[hipath4k]

For trunk to trunk Transfer

1) NNo number number should be same
2) ALL tranfer paramter should be define in COT and COP
3) Zand:- trunk to trunk tansfer should be yes

 

[nhlanhla]

Good day.

Will try that and get back to you.

 

[nhlanhla]

This is my current configuration.

DIS-COT:2,;
H500: AMO COT STARTED

COT: 2 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
RECALL IF USER HANGS UP IN CONSULTATION CALL RCL
TRUNK CALL TRANSFER XFER
CHANGEOVER FROM HOLD TO RING TONE CHRT
CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC
DON'T RELEASE CALL TO BUSY HUNT GROUP BSHT
CAMP-ON AFTER EXTENSION OF INCOMING TRUNK CALLS KNEX
RECORDED ANNOUNCEMENT IF CALL IN HUNT GROUP ANHT
INCOMING CDR BY ZONE OR FROM LINE ICZL
INCOMING CDR ACTIVATE PER TRUNK ICZO
NO TONE NTON
AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESSING
DISPLAY COMPLETED;

IS-COP:1,;
H500: AMO COP STARTED

COP: 1 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
DUALTONE MULTIPLEFREQUENCY DTMF
LINE WITH SUPERVISION AND RELEASE ACKNOWLEDGEMENT LSUP
BACKWARD RELEASE AFTER RELEASE RLSA
TIME DEPENDENT EXCHANGE DIALTONE TDED
NOT 1A, I.E OUTGOING DIGITS NOT WITHHELD NO1A
DIRECT INWARD TRUNK, NO AC INTERCEPT DITW
INTERDIGIT PAUSE 2 (AMO DTIM2: IDGT2) IDP2
MAKE/BREAK RATIO FOR DTMF 1 (PULSE=80MS,PAUSE=80MS) DTM1
AMO-COP -111 CLASS OF PARAMETER FOR DEVICE HANDLER
DISPLAY COMPLETED;

 

[nhlanhla]

DIS-ZAND:ALLDATA;
H500: AMO ZAND STARTED
GENERAL SYSTEM DATA:
====================
TRANSFER = EXTEND , ALERTN = NO ,
AUTHUP = TA ,
RNGBKTN = YES , TRANSINH = NO ,
NIGHT = TA ,
ITRFWD = NO , HOLDTN = MUSIC , ANATESIG = TONE ,
DSSLT = 40, CODTN = YES , CONFSUB = NO ,
DATEDIS = DDMM, CNTRYCD = 3 , RCLLT = NO ,
MELODY = 1, TRCD = , CPBLOWL = 80 ,
CPBUPPL = 100, CUTHRU1A = NO , PREDIA = YES ,
SIUANN = 2, CO = YES , COEXN = 0 ,
CBKNO = 99, SEVDIG = NO , PNNO = 1 -1 -200,
DISPMODE = MODE1, PNODECD = A103 , ROUTOPTP = NO ,
ROUTOPTD = NO , CALLOFF = NO , PARARING = YES ,
DSSDEST = YES , ONEPARTY = YES , MSGDELAY = NO ,
EXCOCO = YES , TRDGTPR = NO , COANN = NO ,
HOTDIAL = NO , TRANSTOG = NO , NOCFW = NO ,
HOLDHUNT = NO , POSTDDLY = NO , EXBUSYOV = NO ,
OVRMST = NO , OVRHUNT = NO , CONITPRO = YES ,
RECHUNT = NO , CALLACMP = NO ;
AMO-ZAND -111 SYSTEM DATA
DISPLAY COMPLETED;
<

 

[hipath4k]

Dis-tacsu
dis-richt
dis-zand:alldata2;

 

[sbcsu]

Also ensure you have TTT added in COS for Trunks and Extensions