Outgoing CLI IP LDK 100

[averageidiot]

have an issue where one of our sites which has a LDK 100 Double Cab with two PRIBS in each card is connected to its own ISDN with 15 channels and DDI Ranges, different Phones send a different DDI dependant on department they recently added some new departments however i can not get it to send the correct DDI i am defiantly going out over the right ISDN, i have also checked with the line provider that they are allowing it there end.

just wondering if anyone had any proven/working method of sending a single DDI from one extension? i have an old old document on sending CLI on the IPLDK but tried all 5 methods with still no joy :/

any information will be of help

regards

 

[doktor]

Let us know the version of your ipLDK-100, seen by [Trans/Pgm]+72. Post the result here.

///doktor
____________________________________

http://www.kandu.dk/spg153996.aspx

 

[SteveBUK]

Hi
When sending out the DDI CLI - if you have tried different methods make sure you return the values to default before trying the next programming method.

Program DDIs as per normal - PGM 231 - Flex DDI, PGM 140 FK 1- Line Type DDI, PGM 143 FK 4 - Conversion Type 2.
PGM 143 FK 12 – CLI Type – Set as Long CLI 1
PGM 143 FK 3 - Call Type – UKNOWN (default)
PGM 114 FK 21 – Set as 3, 6, 10 or the number of digits required by the exchange


In the event of having to start again to try a different option the Default settings are as follows: -

PGM 114 FK 5 – EXT
PGM 114 FK 8 – 0
PGM 114 FK 12 – STA Number
PGM 114 FK 14 – OFF
PGM 114 FK 15 – OFF
PGM 114 FK 18 – Short
PGM 114 FK 19 – Blank

PGM 143 FK 2 – Not Assigned
PGM 143 FK 3 – Unknown

Regards
Steve

 

[smithy704]

for cli outgoing to include the station number -

PGM 146
(PGM230 Note 2)
5 (1) Received Digits 3 Usually 3 DID digits
6 (2) Digit Conversion #X** Where X = the hundreds digit of the station numbering range. (Some sites can be left as #***)
PGM 140
1 CO Type 3 ISDN/MSN
PGM 143
1 COLP Index 01 Allocate a COLP table. (Use this bin in PGM 201)
2 Clip Index 01 Same as COLP table
3 Call Type National
4 CONV Type 2 Use DID flexible table PGM 231
5 DID remove 05 First five digits
PGM 201
Dial Bin No. COLP table BIN 01 “xxxxx” Enter 1st 5 digits of ISDN no. (No area code!)
PGM 146
(PGM200 Note 2)
1 (3) I/C Prefix ON Insert the zero for GSM
2 (4) O/G prefix OFF
PGM 200
9 MY Area Code “X” Where X = the STD area code minus the zero
10 My Area Prefix Code 0 Prefix digit of local area code.
PGM 114
5 ATD/EXT EXT Select EXT
12 ISDN CLI STA “XXX” Where XXX = the STA number (Note 1)
PGM 114
1 Clip LCD display ON ON = CLI will be displayed on LCD
4 CLI MSG wait OFF OFF = CLI message wait will not be displayed
11 CLI name display ON ON = display dial by name if CLI matched in speed bin
14 ISDN CLIR OFF OFF = send CLI to called party
16 DID Restriction OFF OFF = station can receive a DID call