OTM - Configure Ethernet access

[jonttaylor]

Morning Chaps,.,.
Normally any changes on our Option 11 are done in OTM over the serial link.
Our OTM machine does have an extra NIC with a link to the switch,. but I know this was never configured(to me it makes sense to configure as a backup). Is there a guide anywhere to setting up the IP link?,
I know the NIC has static IP of 192.168.1.2 ,. I did a stat host in LD117 (expecting to see a 192 address)and got this, (if its any help).

=> stat host

*** Active Internet Host Table ***
ID Hostname IP Address
-- localhost 127.0.0.1
4 MERIDIAN 220.0.0.100
1 SECONDARY_ENET 137.135.128.254
2 LOCAL_PPP_IF 137.135.192.4
3 REMOTE_PPP_IF 100.1.1.1
-- .255.255.0 0.0.0.0

 

[Firebird Scrambler]

Morning John

I'm guessing that your system was once (or still is?) a BT maintained system. Anyway I have a guide that may help you in setting up the Ethernet link onto your Meridian system.

I'll see if I can place it hear for you.

This procedure lets you change the PABX IP addresses without Warm or Cold starting the PABX.

If there is a Callpilot, Symposium, Tapi server etc this will cause an
Outage of these devices and keep in mind if your changing the IP well
They need to know also. So its much more involved than just this!

Neil Teo 30/5/2003

This example is from an 11C system on 25.30


>ld 117
OAM000

MEM AVAIL: (U/P): 1038524 USED U P: 233655 104076 TOT: 1376255
DISK RECS AVAIL: 401
SURVIVABILITY AVAIL: 0 USED: 0 TOT: 0
=> new host DARWIN_11C 10.42.38.4
INET Data Added

=> pr host

Cabinet # 0
ID Hostname IP Address
1 PRIMARY_ENET 137.135.128.253
2 SECONDARY_ENET 137.135.128.254
3 LOCAL_PPP_IF 137.135.192.4
4 MERIDIAN1 10.42.38.130
5 DARWIN_11C 10.42.38.4
No database file exists for cab#1
No database file exists for cab#2
No database file exists for cab#3
No database file exists for cab#4
OK

=> stat host
*** Active Internet Host Table ***
ID Hostname IP Address
-- localhost 127.0.0.1
1 PRIMARY_ENET 137.135.128.253
2 SECONDARY_ENET 137.135.128.254
3 LOCAL_PPP_IF 137.135.192.4
4 MERIDIAN1 10.42.38.130

=> enl host 5
HOST: "DARWIN_11C" "10.42.38.4" enabled
OK

=> chg elnk active DARWIN_11C
INET Database updated

=> prt elnk
ACTIVE ETHERNET: "DARWIN_11C" "10.42.38.4"
INACTIVE ETHERNET: "SECONDARY_ENET" "137.135.128.254"
OK

=> chg mask 255.255.255.128
INET Data Changed

=> prt mask
SUBNET MASK: "255.255.255.128"
OK

=> pr ro
Cabinet # 0
Route entry(ies) not found.
No database file exists for cab#1
No database file exists for cab#2
No database file exists for cab#3
No database file exists for cab#4
OK

=> stat ro
*** Active Internet Routing Table ***
ID Destination Gateway Port
-- 137.135.128.128 137.135.128.253 0 [qu0]
-- 127.0.0.1 127.0.0.1 -- [lo0]

=> ****
OVL000
>ld 137
CIOD000
.stat elnk

ELNK ENABLED
Ethernet (qu unit number 0):
Host: PRIMARY_ENET
Internet address: 137.135.128.253
Broadcast address: 137.135.128.255
Ethernet address: 00:00:75:45:f8:fd
Netmask: 0xffff0000; Subnetmask: 0xffffff80
0 packets received; 8 packets sent
0 input errors; 8 output errors
0 collisions
.dis elnk

OK
.****
>
OVL000
>ld 48
LNK000
.stat elan

SERVER TASK: DISABLED

.dis elan test
OK
.
TIM000 17:43 29/5/2003 CPU 0

BUG480
BUG480 + 1066E05C 1067B7A0 1093DC2C 115B0A3E 115B0780
BUG480 + 115ACA36 115A9704 115A735C 10959A58 10958878
BUG480 + 1095812A 109565A6 10953A0A 10E3FFC2 10E3F2A8
BUG480 + 10E3EF50
.enl elan
OK
.
BUG480
BUG480 + 1066E05C 1067B7A0 1093DC2C 115B082A 115B0780
BUG480 + 115ACD36 115A9704 115A735C 10959A58 10958878
BUG480 + 1095812A 109565A6 10953A0A 10E3FFC2 10E3F2A8
BUG480 + 10E3EF50

ELAN020 ELAN Server enabled by LD 48
.stat elan

SERVER TASK: DISABLED

.*
.*
.*
.*
OVL000
>ld 137
CIOD000
.enl elnk
Initialize Network Interface.
Network Interface is up.
Host : DARWIN_11C
IP Address : 10.42.38.4
Sub-netmask : 255.255.255.128
OK
.****
>ld 117
OAM000

MEM AVAIL: (U/P): 1038524 USED U P: 233655 104076 TOT: 1376255
DISK RECS AVAIL: 401
SURVIVABILITY AVAIL: 0 USED: 0 TOT: 0
=> ping 10.42.38.1

PING 10.42.38.1 SUCCESSFUL

=> ping 10.42.112.95

PING 10.42.112.95 FAILED

=> new route 10.42.112.95 10.42.38.1 Basically how is the OTM IP reached, by going to gateway at 10.42.38.1
INET Data Added

=> pr ro
Cabinet # 0
ID Destination Gateway Port
2 10.42.112.95 10.42.38.1 0
No database file exists for cab#1
No database file exists for cab#2
No database file exists for cab#3
No database file exists for cab#4
OK

=> enl ro 2 Where “2” is the ID no obtained when printing it above.
ROUTE: "10.42.112.95" "10.42.38.1" enabled
OK

=> st ro
*** Active Internet Routing Table ***
ID Destination Gateway Port
-- 0.0.0.0 10.42.38.1 0 [qu0]
-- 10.42.38.0 10.42.38.4 0 [qu0]
-- 10.42.0.0 10.42.38.1 0 [qu0]
-- 10.42.112.0 10.42.38.1 0 [qu0]
-- 127.0.0.1 127.0.0.1 -- [lo0]
2 10.42.112.95 10.42.38.1 0 [qu0]

=> ping 10.42.112.95

PING 10.42.112.95 SUCCESSFUL ? Woo Hoo!

=>

To tidy things up at the end do a
=> update dbs
This renumbers the Ids to make it pretty basically.


OVL000
>ld 43
EDD000


.ddd

DB SEQ NUM = 210
CONFIG
PHYSICAL MAP
BCS TEMPLATE
PBX TEMPLATE
CUST
ACUST
CLID
ROUTE
DAPC
LTN TN
LTN LNK
TN
SCL


All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.