OS 4K to Panasonic TDE600 SIP trunk without using SIP profile

[Karmozdi]

Dears

Hello,
I want to Trunk a Openscape 4000 to Panasonic TDE600 using SIP trunk, I inserted following commands using port number 5060 on OS4K as SIP server port number and port 35060 on TDE600:

ADD-BFDAT:FCTBLK=1,FUNCTION=HG3550&SIP,BRDBCHL=BCHL60;
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=HG3550,LINECNT=1,UNITS=1;
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=SIP,LINECNT=220,BCHLCNT=50;
CHANGE-BFDAT:CONFIG=OK,FCTBLK=1,ANSW=YES;

ADD-BCSU:MTYPE=IPGW,LTG=1,LTU=2,SLOT=14,PARTNO="Q2324-X500",FCTID=1,LWVAR="0",FCTBLK=1,BCHLSIP=50,BCHL3550=10,ALARMNO=0,IPMODE=IPV4,DHCPV4=NO,DHCPV6=NO;

ADD-CGWB:LTU=2,SLOT=14,SMODE=NORMAL,IPADR=172.16.1.6,NETMASK=255.255.255.128;

CHANGE-CGWB:MTYPE=CGW,LTU=2,SLOT=14,TYPE=GLOBIF,PATTERN=213,VLAN=YES,VLANID=172,DEFRT=172.16.1.125,BITRATE=AUTONEG,TRPRSIP=10,TRPRSIPQ=0,TRPRH323=0,TPRH323A=0,TLSP=4061,DNSIPADR=0.0.0.0,DNSIPAD2=0.0.0.0,USEWANIF=NO,SIPTCPP=5060,SIPTLSP=5061;

CHANGE-CGWB:MTYPE=CGW,LTU=2,SLOT=14,TYPE=LEGKDATA,GWNO=151,GWDIRNO=2500,REGEXTGK=NO;

CHANGE-ZANDE:TYPE=ALLDATA,SCALLOG=YES,GATEKPR=YES;

ADD-BUEND:TGRP=151,NAME="TEHRAN-SIP ",NO=30,TRACENO=0,ACDTHRH=*,PRIONO=1,TDDRFLAG=ON,GDTRRULE=0,ACDPMGRP=0,CHARCON=NEUTRAL;

ADD-TDCSU:OPT=NEW,PEN=1-02-014-0,COTNO=4,COPNO=4,DPLN=0,ITR=0,COS=1,LCOSV=1,LCOSD=1,CCT=" ",DESTNO=144,PROTVAR=ECMAV2,SEGMENT=8,DEDSVC=NONE,TRTBL=GDTR,SIDANI=N,ATNTYP=TIE,CBMATTR=NONE,TCHARG=N,SUPPRESS=0,TRACOUNT=31,SATCOUNT=MANY,NNO=44,ALARMNO=0,FIDX=1,CARRIER=1,ZONE=EMPTY,COTX=4,FWDX=1,CHIMAP=N,CCHDL=SIDEB,UUSCCX=16,UUSCCY=8,FNIDX=1,NWMUXTIM=10,CLASSMRK=EC&G711&G729AOPT,TGRP=151,SRCHMODE=DSC,INS=Y,SECLEVEL=SECURE,HMUSIC=0,CALLTIM=60,WARNTIM=60,DEV=HG3550IP,BCHAN=1&&8,BCNEG=N,BCGR=1,LWPP=0,LWLT=0,LWPS=0,LWR1=0,LWR2=0,DMCALLWD=N;

ADD-RICHT:MODE=LRTENEW,LRTE=151,LSVC=ALL,NAME="SIP-TRK-TEH1 ",TGRP=151,DNNO=1-1-151,ROUTATT=NO,EMCYRTT=NO,PDNNO=0,CHARCON=NEUTRAL,CONFTONE=NO,RERINGRP=NO,NOPRCFWD=NO,NITO=NO,CLNAMEDL=NO,FWDSWTCH=NO,LINFEMER=NO,NOINTRTE=NO;

ADD-LODR:ODR=44,CMD=ECHO,FIELD=2;
ADD-LODR:ODR=44,CMD=END;

ADD-LDAT:LROUTE=151,LSVC=ALL,LVAL=1,TGRP=151,ODR=44,LAUTH=1,CARRIER=1,ZONE=EMPTY,LATTR=NONE,VCCYC=4,GW1=152-0;


ADD-WABE:2500,,,TIE,N,,,,,,,,;

ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP="2500"-"Z",DPLN=0,LROUTE=151,LAUTH=1,PINDP=N;

ADD-GKREG:GWNO=151,GWATTR=INTGW&HG3550V1&HG3550V2&SIP,DIPLNUM=0,DPLN=0,LAUTH=1,INFO="INTERNAL SIP TR";
ADD-GKREG:GWNO=152,GWATTR=EXTGW&HG3550V1&HG3550V2&SIP,GWIPADDR=192.168.100.25,GWDIRNO=8287,DIPLNUM=0,DPLN=0,LAUTH=1,INFO="EXTERNAL SIP TR",SECLEVEL=TRADITIO;

and configured the STMI4 card in WBM to not using SIP profile.
I have Ping of Panasonic side on STMI card WBM and wise versa.
Trunk Port becomes Open But Panasonic TDE600 cannot send calls to Os4K.

in Panasonic:
We configured as attached file.

 

[Karmozdi]

Then I Changed the Config on Panasonic To state of not using SIP profile and registration = Disabled.

 

[Moriendi]

You should not be using native SIP trunks without a profile, supported use is via profile only. But it should still work. You've only added 8 channels in your TDCSU and 10 channels everywhere else, but I don't think that will be your problem.

You need a trace from the card to determine what is happening. Browse to the card, Maintenance, Traces & Events, Delete All Logs. Then trace profiles, activate 1.1.2(detail) SIP Trk. General problems, and make a test call. Then Load All Logs to download a zip. Have a look in there, you will see the call processing from the SIP engine and also the Qsig messaging to the 4K (if there is any).

 

[Karmozdi]

Dear Moriendi

Thank you so much, I think it is Panasonic side Problem, I'll check and response.