Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Option 11C - Setting up a TN from scratch

Status
Not open for further replies.

socketdown

Programmer
Nov 16, 2019
3
CH
Hi everyone. First post here.

I saved a Option 11C from a factory demolition a few months ago. The thing is I'm a programmer and don't have any experience working with PBXs, so bear with me.
I reset the switch to factory default and configured the CDB. then I saw that there were no loops listed in ld 22, prt, cequ. Since I have 6 cards installed, and the card I want to program is in slot 4 (it's an analog NT4K02PC card) I added a new superloop in ld 97, chg, supl, N004. Now this one shows up as a phantom loop in ld 22. Also I have licenses for 40 Analog phones and plenty of TNs.

However when I program a 500 analog set on loop 4 it still doesn't enable my analog card in slot 4. Enabling it in ld 32, enlc 4 gives me an NPR665 since it is a phantom loop.

Did I miss something or did I something wrong?

This is a pretty steep learning curve for me, I try to research as much as I can on my own. However I've been stuck on this for a few weeks by now and really need some inputs.
Thanks for any replies!

Best Regards
Roman
 
Hello Roman

It would have been easier to have kept the old programming.As you have defaulted the system, you might want to follow the attached guide that is old, but should help you.

What release of software is the system?. Do a TID, ISS and SLT in LD 22.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
Thanks for your reply and for the guide!

The system is running release 7.50
I defaulted the system because I didn't get any credentials with it (I just dismantled everything what was available on site). With it came an installation USB stick for rls. 7.50 and old configuration backups and one keycode file (which I re-used during the factory reset procedure), so I believe not everything is lost there.

in ld 22, SLT returns

System type is - Communication Server 1000E/CPMG128 Linux
CPMG128

IPMGs Registered: 0
IPMGs Unregistered: 0
IPMGs Configured/unregistered: 0


TRADITIONAL TELEPHONES 40 LEFT 40 USED 0
DECT USERS 0 LEFT 0 USED 0
IP USERS 0 LEFT 0 USED 0
BASIC IP USERS 0 LEFT 0 USED 0
TEMPORARY IP USERS 0 LEFT 0 USED 0
DECT VISITOR USER 0 LEFT 0 USED 0
ACD AGENTS 10 LEFT 10 USED 0
MOBILE EXTENSIONS 0 LEFT 0 USED 0
TELEPHONY SERVICES 0 LEFT 0 USED 0
CONVERGED MOBILE USERS 0 LEFT 0 USED 0
AVAYA SIP LINES 0 LEFT 0 USED 0
THIRD PARTY SIP LINES 0 LEFT 0 USED 0

PCA 0 LEFT 0 USED 0
ITG ISDN TRUNKS 0 LEFT 0 USED 0
H.323 ACCESS PORTS 0 LEFT 0 USED 0
AST 1 LEFT 1 USED 0
SIP CONVERGED DESKTOPS 0 LEFT 0 USED 0
SIP CTI TR87 0 LEFT 0 USED 0
SIP ACCESS PORTS 0 LEFT 0 USED 0
RAN CON 8 LEFT 8 USED 0
MUS CON 1010 LEFT 1010 USED 0

IP RAN CON 0 LEFT 0 USED 0
IP MUS CON 0 LEFT 0 USED 0
IP MEDIA SESSIONS 0 LEFT 0 USED 0
TNS 65535 LEFT 65534 USED 1
ACDN 24000 LEFT 24000 USED 0
AML 16 LEFT 16 USED 0
IDLE_SET_DISPLAY NORTEL
LTID 65535 LEFT 65535 USED 0
RAN RTE 512 LEFT 512 USED 0
ATTENDANT CONSOLES 65535 LEFT 65535 USED 0
IP ATTENDANT CONSOLES 0 LEFT 0 USED 0
BRI DSL 10000 LEFT 10000 USED 0
DATA PORTS 65535 LEFT 65535 USED 0
PHANTOM PORTS 65535 LEFT 65534 USED 1
TRADITIONAL TRUNKS 65535 LEFT 65535 USED 0
ELC ACCESS PORTS 0 LEFT 0 USED 0
DCH 254 LEFT 254 USED 0

ISS returns

VERSION 4421

System type is - Communication Server 1000E/CPMG128 Linux
CPMG128

IPMGs Registered: 0
IPMGs Unregistered: 0
IPMGs Configured/unregistered: 0

RELEASE 7
ISSUE 50 Q
IDLE_SET_DISPLAY NORTEL

IPMG TYPE CSP/SW MSP APP FPGA BOOT DBL1 DBL2

and TID delivers this message

TAPE ID:
LOADED 068842325

I hope this can help
 
Hello Roman

That explains why you had to build a new superloop. The Option 11c systems used a SSC card as a processor but this changed when the CPPM card came out. Finally the CPMG was used which you have. The attached guide is old, but you need to refer to page 4 to create a virtual loop rather than a phantom loop.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
I read the guides now tried setting up an virtual loop instead of a phantom one, however I can't program a 500 set on it since it always delivers a SCH5511.
May it be that virtual loops are only compatible with IP phones?

Also do you have additional documentation regarding loops and superloops (e.g. what types of loops serve what kind of purpose, how to set them up correctly) since I can't seem to find any information on that online or in the docs (maybe I also just missed it since the docs are huge)?

Thanks for your time!
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top