Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Opt 11c will not load 2

Status
Not open for further replies.

hawks

IS-IT--Management
Oct 9, 2002
5,869
US
Option 11c working fine then powered it down and moved to another location. when I powered it back up the system keeps putting out the following and never loads Can anyone point me in a direction?

Meridian Small System Controller
Pre-Boot: 03 dev2.37
Flash Boot: NTDK34AA_r10 dev2.43
Reset Reason: C0, 0 - Reset due to Power Up
SRAM: 128 kBytes
DRAM: 8 MBytes, speed=60 ns
Security ID: xxxxxxxx type: NT_STD
Backup Flash: 1572 kBytes
Program Store: 32 MBytes
Flash Drive: 8 MBytes
Expansion board #1 not installed.
Expansion board #2 not installed.
Ethernet MAC address: 00.00.75.45.BE.CA
PCMCIA card not installed in drive A.
PCMCIA card not installed in drive B.

*** To invoke install setup program from PCMCIA enter CONTROL-I ***

Executing power up self tests
Power up self test passed
DISKOS to be run.
Verifying Diskos.

*** OS RESTART ***
Meridian 1 X11 System Software
Release : x112424
Created : Thu Jun 10 22:46:53 PDT 1999
Loaded : 7/1/96 5:14:26

Copyright(C) 1972-1997 Northern Telecom, Inc. All Rights Reserved.
VxWorks 5.2
Copyright(C) 1984-1995 Wind River Systems, Inc. All Rights Reserved.
Use of the above software subject to terms of a license agreement. U.S. Government users subject to "Restricted Rights" under FAR & DFAR.

BUG6343: Unable to initialize drive. pDrv = 0x2009925c, task = tStartup, tid = 0x203373b8 , pc = 0x1011e3c4
BUG6343: Unable to initialize drive. pDrv = 0x2009925c, task = tStartup, tid = 0x203373b8 , pc = 0x1011e3f6

BUG7436 OS 0: WARNING "Bad Reason Data"

RPT: can't create log file c:/u/rpt/rpt.log (errno 0xd0001)
Unable to find startup script.
PCH1309: Error creating patch retention file "c:/u/patch/reten/reten.pch"
PCH1201: Error initializing patch retention.
Patch retention will not be possible.

BUG7462 OS 0: WARNING "Patch Init"

0x2031661c (tRptD): (7/1/96 5:14:30.000) RPT00003 Unknown report (not in DB): cat# = 10, report# = 7499
0x2031661c (tRptD): (7/1/96 5:14:32.000) SRPT0730 OS 0: Cold Start
Release: x112424
Created: Thu Jun 10 22:46:53 PDT 1999
0x2031661c (tRptD): (7/1/96 5:14:32.000) PCH00313 Error initializing patch retention file
Make sure the disk is ok. Reten info may be out of date
[ Initialising Orbix Error handling ]
[ Constructing a new Proxy Factory Table ]
Unable to open /p/data/VERSION
 
Hi,

I think your flash drive is dead/scrambled (did you drive over a lot of bumps?!? ;-)... If you know PDT go to PDT and look if you can access the C and/or Z drive.

If you can't access both of the drives, I hope you have an external backup or you really have a problem (You have lost the database)

I'm almost 100% sure you need to reinstall the software...

If you do not know PDT, look for a good supplier how does, because I also think you can save some (If not all) data...

Marc D.
 
are you booting with a pcmia card installed, if not your daughter board data base is corrupted, you will need to restore your database from the z: drive, xbk or pcmia archive.
 
Thanks that is what I was afraid of. Not worried about losing the database because I was just starting to reprogram anyway. It did have CCR/Link will I loose that?
 
CCR has it's own OS/database etc. you will need to re-program the aml
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top