Openscape 4000 Stop Showing Caller ID internal calls 2

[Hamid2018]

Dears Hi,
I manage an OpenScape 4000 V6, The customer insists on setting up several SIP extensions in the 'team and top' group, so I manually made this available by following command lines:

ADD-WABE:CD=9602,DAR=STN,CHECK=N;
ADD-WABE:CD=9789,DAR=STN,CHECK=N;
ADD-WABE:CD=9603,DAR=HUNT,CHECK=N;
ADD-SBCSU:STNO=9602,OPT=OPTI,CONN=IP2,DVCFIG=OPTIIP,TSI=1,COS1=1,COS2=1,LCOSV1=8,LCOSV2=8,LCOSD1=8,LCOSD2=1,DPLN=0,ITR=0,SSTNO=N,COSX=0,SPDI=0,IDCR=N,REP=0,STD=1,SECR=Y,INS=Y,ALARMNO=0,RCBKB=N,RCBKNA=N,DSSTNA=N,DSSTNB=Y,DIGNODIS=N,CBKBMAX=5,HEADSET=N,HSKEY=NORMAL,CBKNAMB=Y,TEXTSEL=ENGLISH,HMUSIC=0,CALLOG=ALL,COMGRP=0,IPCODEC=G729AP;
ADD-SBCSU:STNO=9789,OPT=FPP,CONN=SIP,PEN=1-5-5-88,DVCFIG=S0PP,COS1=1,COS2=1,LCOSV1=4,LCOSV2=8,LCOSD1=1,LCOSD2=1,DPLN=0,ITR=0,SSTNO=N,COSX=0,SPDI=0,PROT="SBDSS1",PERMACT=Y,INS=Y,ALARMNO=0,OPTIDX=10,RCBKB=N,RCBKNA=N,CBKBMAX=5,HMUSIC=0,PASSWD="9789",USERID="9789",SECZONE="9789",AUTHREQ=Y;
CHANGE-TAPRO:STNO=9602,DIGTYP=OPTISET,KY10=LNR,KY12=CBK,KY13=DND,KY14=SPLT,KY15=CONS,KY16=DSS;
ADD-PERSI:TYPE=STN,STNO=9602,NAME="9603 Secretary*";
ADD-PERSI:TYPE=STN,STNO=9789,NAME="9602 Executive*";
ADD-SA:TYPE=VCE,CD=9603,ITR=0,STNO=9602&9789,STYPE=LIN,CQMAX=1,NAME=" ",DISPTYPE=EXT;
ADD-ZIEL:TYPE=FWD,SRCNO=9602,SI=VCE,DESTNOF=9789,NAME="9602 Executive",DTYPE=CFDND,ITYPE=EXT,CFVAR=SYSTEM;
ADD-ZIEL:TYPE=FWD,SRCNO=9602,SI=VCE,DESTNOF=9789,NAME="9602 RAVAND",DTYPE=CFDND,ITYPE=INT,CFVAR=SYSTEM;
ADD-ZIEL:TYPE=DSS,SRCNO=9602,KYNO=16,DESTNOD=9789,DEV=BD,SLKTYPE=SLKSTNO;
ADD-ACTDA:TYPE=STN,STNO=9602,FEATCD=FWD,CFVAR=SYSTEM,SI=VCE;
ADD-ACTDA:TYPE=STN,STNO=9602,FEATCD=VCR;
ADD-ACTDA:TYPE=STN,STNO=9602,FEATCD=INHUNT,SIINHT=VCE;
ADD-ACTDA:TYPE=STN,STNO=9789,FEATCD=INHUNT,SIINHT=VCE;
ADD-ACTDA:TYPE=STN,STNO=9789,FEATCD=FWD,CFVAR=STATIONV,DTYPE=CFU,ITYPE=GEN,SI=SPCH,DESTNO=9602;

Questions:
1- now the manager with SIP extension 9789 calls other users (for example 9610 on the display of called number shows 9789 is calling and we need to show 6902, how can we do this?
2- on the display, the LCD of the Secretary's phone number is 9602 as it is in fact, We need to set it to 9603 (I know 9603 is not a station number just need to change the information on the LCD as needed). how do I change LCD information while the phone is in idle mode?
3- I think I can stop showing internal calls caller ID and use persi , Name field to do the request but still the called station see caller real ID on display, how to turn of caller ID for HFA and SIP subscribers?
(like: CHANGE-FEASU:TYPE=D,CM=CLIP; for analog)

Any help is appreciated

 

[sbcsu]

You could use CHESE (Manager Secretary Working) OR KCSU (Key System Functionallity)

 

[Hamid2018]

You could use CHESE (Manager Secretary Working) OR KCSU (Key System Functionallity)

Dear SBCSU,
Thank you so much, but chese doesn't support SIP extension.

I can use the cheese command line just if I have loadware for Mitel 5340 & 5440 IP-Phones with HFA protocol.

 

[sbcsu]

OK Then use Key System Functionallity - KCSU - End User will push a button to decide on what extension number to dial out on - that number then will be shown to the other user

 

[Moriendi]

This is nuts, HFA has best chance of working here with CHESE or KCSU. But customer insists on SIP, on a V6 4K, software which is 13? years old with limited SIP functionality (S0PP not UFIP). But even on V11, HFA would be better.

Customer should be told to use HFA.

Also, you want to turn off caller ID, but they are using digital feature phones? If they don't want to see who's calling, give them an analog phone with no display.

There was a ZAND ALLDATA parameter to decide some calling ID behaviour, parameter was something like MODE1, MODE2, MODE3 etc, dis-zand you'll see it. It may not work on the later phones or SIP and is a systemwide parameter anyway.

 

[sbcsu]

Indeed, Moriendi is correct - you need to explain to the customer that if they want functions to work that they have to accept the limitations of what they are trying to do !
That parameter is as follows:
DIS-ZAND:ALLDATA;
CHA-ZAND:TYPE=ALLDATA,DISPMODE=??

By default it is MODE1
MODE1 DISPLAY EXTENSION AND NAME
MODE2 DISPLAY EXTENSION ONLY
MODE3 DISPLAY NAME ONLY
MODE4 DISPLAY EXTENSION AND NAME, POSS. EXTENSION ONLY
MODE5 DISPLAY EXTENSION AND NAME,POSS. # INST.OF EXTENS.

 

[Hamid2018]

Dear SBCSU and Dear Moriendi
Thank you dears for your kind help, I'm going to resolve the problem for the customer tomorrow and Report.
I would change-ZAND:Alldata,mode3;
then I would add-persi caller id for all extensions;