Only Extns with NCOS 7 able to make calls between CS1K and IPO

[MSAtech]

Unable to make calls from CS1K extensions to IP Office Extensions if the NCOS of CS1K extensions is not 7. If NCOS 7 then CS1K extns are able to make calls to IPO extns. QSIG is set-up between CS1K and IPO. All other calls are working fine. I copied LD 49 CRNO 7 values over to CRNO 6, I assigned NCOS 6 to an extension, still the CS1k to IPO calls fail. However If i change the NCOS to 7 then the same extension works fine. Looks as if somewhere the NCOS 7 is mapped to that QSIG trunk. I may be wrong.. Please share your thoughts.Thank you

REQ: prt
TYPE: trk
TN 21 1
DATE
PAGE

DES QSIG_TIE_TO_IPO
TN 021 01 VIRTUAL
TYPE TIE
CDEN SD
CUST 0
TRK PRI2
PDCA 2
PCML A
NCOS 7
RTMB 24 1
B-CHANNEL SIGNALING
TGAR 2
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD XREP BARD SPCD
P10 VNL
TKID
AACR NO
DATE 9 AUG 2016


**


TYPE adan dch 12

ADAN DCH 12
CTYP MSDL
MG_CARD 000 0 02
PORT 1
DES QSIG_to_IPO
USR PRI
DCHL 21
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ESIG
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
QCHID YES
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7


**

REQ: prt


TYPE: rdb


CUST 0


ROUT 24




TYPE RDB

CUST 00

ROUT 24

DES QSIG_TIE_TO_IPO

TKTP TIE

NPID_TBL_NUM 0

ESN NO

RPA NO

CNVT NO

SAT NO

RCLS EXT

VTRK NO

NODE

DTRK YES

BRIP NO

DGTP PRI2

ISDN YES

MODE PRA

IFC ESIG

SBN NO

PNI 00000

NCNA NO

NCRD NO

CTYP NXX

INAC NO

ISAR NO

CPFXS NO

HNTN 029

HLCL 9784

DAPC YES

TBL 0

INTC NO

MBXR NO

DSEL VOD

PTYP DTT

AUTO NO

DNIS NO

DCDR NO

ICOG IAO

SRCH LIN

TRMB YES

STEP

ACOD 1024

TCPP NO

TARG

CLEN 1

BILN NO

OABS

INST

IDC NO

DCNO 0 *

NDNO 0

DEXT NO

ANTK

SIGO STD

MFC NO

ICIS YES

OGIS YES

PTUT 0

TIMR ICF 512

OGF 512

EOD 13952

NRD 10112





PAGE 002



DDL 70

ODT 4096

RGV 640

GTO 896

GTI 896

SFB 3

NBS 2048

NBL 4096



IENB 5

TFD 0

VSS 0

VGD 6

DTD NO

SCDT NO

2 DT NO

DRNG NO

CDR NO

NATL YES

SSL

CFWR NO

IDOP NO

VRAT NO

MUS YES

MRT 99

PANS YES

RACD NO

FRL 0 0

FRL 1 1

FRL 2 2

FRL 3 3

FRL 4 4

FRL 5 5

FRL 6 6

FRL 7 7

OHQ NO

OHQT 00

CBQ NO

AUTH NO

TDET NO

TTBL 0

ATAN NO

PLEV 2

OPR NO

ALRM NO

ART 0

PECL NO

DCTI 0

TIDY 1024 24

SGRP 0

ARDN NO

AACR NO

 

[KCFLHRC]

There isn't anything wrong. Change the NCOS on the trunks to a value the same or lower than the ext's NCOS that you want to make the call.

 

[StanleySteamer]

How do you dial the extensions? Do you dial an access code first or simply the extension number? If it's the latter then you are likely using CDP so the call s are controlled by a Route List Block.
Print a DNB on the CS1K for one of the IP Office extensions to see what it gives you,

 

[MSAtech]

Apologize for the late reply. This is my first post with a response and I did not get any notification. I know how to check for any response now.

Yes KCFLHRC , I have changed the FRL in RLI to the lowest (0) as it is only a internal trunk. Calls are working fine now. Thank you for the fix.
Appreciate your assistance.

Yes StanleySteamer, I dial the extensions as it is and a CDP entry is added for all extensions added in IPO.

Now there is a new issue. Name is not getting displayed when a call is made between CS1K to IPO and vice versa. Can you please share your suggestions.

Thank you

 

[Firebird Scrambler]

From what I recall, you need to change the DCH 12 RCAP setting to ND3

TYPE adan dch 12

ADAN DCH 12
CTYP MSDL
MG_CARD 000 0 02
PORT 1
DES QSIG_to_IPO
USR PRI
DCHL 21
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ESIG
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
QCHID YES
RCAP COLP
(Add in ND3)
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

Details from 2 previous problem reportS are listed below that might help you.

CS1000E rls 4.5 with a QSIG link from the MG1000T to a third-party switch
Users on the third-party switch dialling a set on the CS1000E did not see the Called Party name displayed on ringing, only after call answer.

Changed RCAP on the VDCH to ND3 on both the CS1000E and the MG1000T to resolve.

ND3 ensures the same level of service between the MCDN Name Display and QSIG Name Display supplementary services.

##########################################################################

You might also need to add in the message waiting feature (QMWI)

Problem Resolution

Fix:
Nortel's Meridian switches with CallPilot support the MWI feature. The following pre-requisites are required for the MWI to work with the Cisco over QSIG:

For the Meridian 1 PBX to support the QSIG MWI feature, the PBX must at least have an Enterprise software level (to get ISDN Tie lines) with X11 Release 25.40 or 25.40B software (to get QSIG MWI).
In addition to NMS software and Phantom TN Features, the following packages must be installed on the PBX:
- PKG 305 (QSIG Generic Function)
- PKG 316 (QSIG Supplementary Services)
- PKG 263 (Qsig Basic Call/Name Display)
- PKG 175 (Network Message Service)

The configuration of the Dchannel of the QSIG should look something like as below:

ADAN DCH 32
CTYP TMDI
CARD 32 --- defines card in slot 32 (loop 32) as the QSIG trunk to CCM
PORT 1
DES Qsig
USR PRI
DCHL 32
OTBF 127
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC ISGF --- defines switch-type ISO QSIG with GF platform
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP QMWI --- enables MWI feature across QSIG trunk
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

##################################################################

If you don't have RCAP = ND3, then try ND2.




Firebird Scrambler
Nortel and Avaya Meridian 1 / Succession and BCM / Norstar Programmer

Very advance high level knowledge on the Linux BCM phone system.

Website

http://somertel.myfreesites.net

 

[MSAtech]

Thanks for the reply ( FirebirdScrambler). I do not get the option ND2 or ND3 as the interface I selected was ESIG and not ISGF as you have mentioned. In ESIG interface I only get the option (NDi). I could not get the trunk up with ESGF hence opted for ESIG. Is there any option to be tried in ESIG , before I can think of changing the interface to ISGF as the site is already in production.

 

[Firebird Scrambler]

Did the option ND1 work for you?.

Firebird Scrambler
Nortel and Avaya Meridian 1 / Succession and BCM / Norstar Programmer

Very advance high level knowledge on the Linux BCM phone system.

Website

http://somertel.myfreesites.net