Off Premise calling on a MICS with 4.2SW 1

[BeavisLee]

Is is possible to configure off premise calling on this system/software release? If it is, do I need any special hardware and what is required to configure it? Thanks!

Kevin

 

[hawks]

not sure what your asking

 

[BeavisLee]

This is the situation. I would like to have our directors dial our head office from their cell phone or home, grab a trunk that has overseas access and call out so these calls would be billed to the company. Is this possible on this system? Thanks for the quick reply!

 

[hawks]

Yes look at DISA in the book I don't have it in front of me right now. sorry

 

[jerryreeve]

You have to have DTMF Receiver modules available to the system. the book calls for DISA to get this out of an E&M card but the COMBO card is supposed to supply DTMF Receivers for the T1 Channels.

If voting could really change things, it would be illegal.

JerryReeve
Communications Systems Int'l
com-sys.com

 

[BeavisLee]

Thanks much for the help thus far folks .. I have an unused E&M card in the system, how do i go about programming it to ake this work?

 

[mroberts]

You will need a back door line. A specific line that will only be used for this purpose.

Terminals&Sets - Next
Lines - Show
Show line: ___ - Enter the designated back door line
200:200 - SHow
Trunk line data - SHow
Trunk type: loop - Next
Line type: Public
Dial mode: tone - Next
PrimeSet: 221 - Next
Dstnct Rng: None - Next
Auto Privacy: Yes - Next
Trunk Mode: Super - Next
Ans mode: Auto - Next
Ans with DISA: Y - Next
Link at CO: Y - Next
Aux Ringer; N - Next
Full Auto Hold: N - Next
LossPkg: Medium CO - Next
--end of list---
Header all the way back to Lines
Lines - Next until you see
Passwords - Show
COS pswds - Show
Show pswd#: ___ - just hit next
COS Pswd: 00 - SHow
Pswd: ______ - Enter a 6 digit password
Pswd: 123456 - Next
User Flt:00 - This is fine as filter 00 is unrestricted and cannot be changed. Next
Line Filter: None - Change this to 00 as well just as a CYA.
Next
Remote Pkg:None - Change to 04 (the package we will build)
Header back to Passwords then Next to

System prgrming - Show
Hunt groups - Next until you see
Remote access - Show
Rem access pkgs - Show
Show pkg: 04 - This is the package that is by default on all lines - Rem pkg 04 - Show
LinePool Access - SHow
PoolA: Y - If pool A is the one they are using for outside lines, then just leave it alone. If they use a different pool then press next to the appropriate pool and set it to Yes.
Header to LinePool access - Next

We he calls the back door number he will hear stutter dial tone, he will enter his password and then get 'system' dial tone, he will then dial his regular line pool access code for his regular lines and dial out.

Someone check me on this programming before I copy it to a cheat sheet.

MRoberts

http://www.a1teletronics.com

 

[BeavisLee]

MRoberts, Thanks bunches for that set of instructions. Can't wait to give it a try. Just to be sure ... I connect this back door line to a regular LS/DS trunk port correct?

 

[mroberts]

Yep! That's all you need.

MRoberts

http://www.a1teletronics.com

 

[telemarv]

looks right to me Melissa

 

[BeavisLee]

I have followed the instructions to the letter and it works ... kinda. I dial in enter the code and dial out however after I hang up the backdoor line remains "in use" for a long time .. 3-5 minutes! Thought it might have been a dodgy trunk card so I ordered a new one but same thing happens. What am I doing wrong? Thanks.

 

[galfaro]

Verify your programming for your backdoor line. Disconnect supervision maybe an issue. Verify the port on your LS/Ds card is the right one for your line.
Gabriel