AnthonyHardy
IS-IT--Management
CS1000 involved: We're changing our ld lines to another switch (already connected to the cs1000 via pri, functional).
Currently, we dial 4 to access ld lines (8 tie trunks on the cs1000). I need to re-route that to the other switch across the PRI.
I've been doing a lot of searching, trying to figure out exactly what I will need to change and here's what I have found so far:
>ld 20
REQ: prt
TYPE: dn
TYPE DNB
CUST 0
DN 4
DATE
PAGE
DES
DN 4
TYPE RDB
ROUT 3
So, it looks like dn of 4 uses ROUT 3. I need it to use ROUT 11, but I'm not sure how to change that.
Here's RDB 3:
>ld 21
PT1000
REQ: prt
TYPE: rdb
CUST 0
ROUT 3
TYPE RDB
CUST 00
DMOD
ROUT 3
DES ATTNET
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK NO
ISDN NO
PTYP ATT
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 4
TARG 03
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
STYP SDAT
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
IENB 5
TFD 0
VSS 0
VGD 6
SST 5 0
NEDC ETH
FEDC ETH
CPDC NO
DLTN YES
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO
VRAT NO
MUS YES
MRT 8
PAGE 002
MANO NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO
You can see the ACOD of 4 there, so I'm guessing that's how the route to the tie trunks is made (doing an LTM confirms that the current ld trunks are associated with ROUT 3 and that ROUT 11 is the other switch).
Currently, I have a DSC that routes 79xxxx to ROUT 11, so I thought I could perhaps just remove the RDB 3 and create a DSC (4) that would point to ROUT 11 as well, but I'm nervous about doing that as I don't know if I could simply add the RDB back and go back to the way we currently handling ld calls. I also thought that perhaps I could change RDB 3 and make the ACOD 49 or something else (does it have to be an available dn?), but I can't change the ACOD to 49 or even another available dn (101 is available).
Ignorance sucks . . Any ideas?
Currently, we dial 4 to access ld lines (8 tie trunks on the cs1000). I need to re-route that to the other switch across the PRI.
I've been doing a lot of searching, trying to figure out exactly what I will need to change and here's what I have found so far:
>ld 20
REQ: prt
TYPE: dn
TYPE DNB
CUST 0
DN 4
DATE
PAGE
DES
DN 4
TYPE RDB
ROUT 3
So, it looks like dn of 4 uses ROUT 3. I need it to use ROUT 11, but I'm not sure how to change that.
Here's RDB 3:
>ld 21
PT1000
REQ: prt
TYPE: rdb
CUST 0
ROUT 3
TYPE RDB
CUST 00
DMOD
ROUT 3
DES ATTNET
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK NO
ISDN NO
PTYP ATT
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 4
TARG 03
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
STYP SDAT
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
IENB 5
TFD 0
VSS 0
VGD 6
SST 5 0
NEDC ETH
FEDC ETH
CPDC NO
DLTN YES
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO
VRAT NO
MUS YES
MRT 8
PAGE 002
MANO NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO
You can see the ACOD of 4 there, so I'm guessing that's how the route to the tie trunks is made (doing an LTM confirms that the current ld trunks are associated with ROUT 3 and that ROUT 11 is the other switch).
Currently, I have a DSC that routes 79xxxx to ROUT 11, so I thought I could perhaps just remove the RDB 3 and create a DSC (4) that would point to ROUT 11 as well, but I'm nervous about doing that as I don't know if I could simply add the RDB back and go back to the way we currently handling ld calls. I also thought that perhaps I could change RDB 3 and make the ACOD 49 or something else (does it have to be an available dn?), but I can't change the ACOD to 49 or even another available dn (101 is available).
Ignorance sucks . . Any ideas?