Nortel and Ericsson MD110 QSIG connectivity

[kondalisa]

I have connected a Ericcson PBX with Nortel 11c rls 4.5 using E1 connectivity(qsig). It is working Ok accept i dont get name or number when a erricson extension calls nortel pbx extension. i get only the route and member number. I tried different RCAP entries AT nortel pbx but no success. The Nortel extension number and name is displaying ok on erricson extension. When i check Dchannel messaging at nortel pbx it shows no CLID.
Does anybody have any experience connection erricson pbx with nortel and name/ext number displaying at both side???
I am really new to ericsson on dont knows how to play with QSIG setting at ericsson pbx for name display.
I will be very thankful if you guys guide some setting at ericsson pbx for name display on nortel extension or can somebody put a sample config of ericsson MD110 and Nortel config from there practical experience.??
Regards

 

[Satellite1900]

Hi,
Can you press the command RODAI, ROCAI RODDI of Q-SIG MD110 to Nortel?
In addition, the command KSCAP of extension.

Regards

 

[whosrdaddy]

to be complete, also add NUTRP, and RONDP:ROU=x printouts.

/Daddy

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[Monrovia]

Hi,
Can you press the command RODAI, ROCAI RODDI of Q-SIG MD110 to Nortel?
In addition, the command KSCAP of extension.

Regards

Dear Kondalisa, actually satellite1900 was asking for the print out of the commands
RODAP,ROCAP,RODDP, and KSCAPIR=XXXX;

 

[kank]

At Nortel QSIG license is abnormaly expensive. So sometimes they do not put in the system. In most cases they use ISDN PRA like connecting to PSTN. Be sure about you have the licsnse on Nortel. Secondly post the print outs that are asked.

 

[kondalisa]

Hi Guys. Below are the captured as advised. Please note that an ericsson tech at site is helping me for these captures.

************* Note **************
Rout 1 and 56 are for CS1000 Nortel
Consono MD101 BC # 11, SP # 13
***********************************

CAPTURE
-------

<RODDPEST=05;
EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
05 1 150510000000125000500000 0 3 0

END

<RODIPRN=1;
DIRECTION DATA
DRN ROU CSIU FRL
1 56 10111111
1 01011101

END

<RODAP:ROU=1&56;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
1 SL60 H'00000350 H'15580000 H'46200000 NO
56 SL60 H'00000350 H'15580000 H'46200000 NO

END

<ROCAP:ROU=1&56;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
1 112000000001101 5 3110000000 0 30 128 00080812 111111000031 001100
56 112000000006101 7 3110000000 0 30 128 00070715 111111000031 001100

END

<ROEDP:ROU=1,TRU=ALL;
ROUTE EQUIPMENT DATA
ROU TRU EQU SQU INDDAT CNTRL
1 001-1 001-1-00-01 H'000000000000
1 001-2 001-1-00-02 H'000000000000
1 001-3 001-1-00-03 H'000000000000
1 001-4 001-1-00-04 H'000000000000
1 001-5 001-1-00-05 H'000000000000
1 001-6 001-1-00-06 H'000000000000
1 001-7 001-1-00-07 H'000000000000
1 001-8 001-1-00-08 H'000000000000
1 001-9 001-1-00-09 H'000000000000
1 001-10 001-1-00-10 H'000000000000
1 001-11 001-1-00-11 H'000000000000
1 001-12 001-1-00-12 H'000000000000
1 001-13 001-1-00-13 H'000000000000
1 001-14 001-1-00-14 H'000000000000
1 001-15 001-1-00-15 H'000000000000
1 001-17 001-1-00-17 H'000000000000
1 001-18 001-1-00-18 H'000000000000
1 001-19 001-1-00-19 H'000000000000
1 001-20 001-1-00-20 H'000000000000
1 001-21 001-1-00-21 H'000000000000

END

<ROEDP:ROU=56,TRU=ALL;
ROUTE EQUIPMENT DATA
ROU TRU EQU SQU INDDAT CNTRL
56 001-1 001-1-00-22 H'000000000000
56 001-2 001-1-00-23 H'000000000000
56 001-3 001-1-00-24 H'000000000000
56 001-4 001-1-00-25 H'000000000000
56 001-5 001-1-00-26 H'000000000000
56 001-6 001-1-00-27 H'000000000000
56 001-7 001-1-00-28 H'000000000000
56 001-8 001-1-00-29 H'000000000000
56 001-9 001-1-00-30 H'000000000000
56 001-10 001-1-00-31 H'000000000000

END

I am now totally dependent on you guys now as Nortel and Ericsson tech on site are out of ideas why ericsson name/CLi wont showing on nortel extension.

I also tried ISGF/ESGF with different setting but still wont getting Ericsson name and CLI and Monitoring messaging at Nortel shows NO CLI. We also consulted nortel and opened a ticket but after there investigation of incoming messaging and nortel config they are also saying that we are not getting name/CLI from Ericsson.

 

[kondalisa]

Any help?

 

[mundus]

Try adc d5=0 in RODDI, Nortell don't supported Aastra UUIx.
The same with vari d2 and d3 =00 - no UUIx.
adc d25 should be set to 1 - Call back/call compl. as Generic.
adc d13 = 1 sending TCM to a Nortell ??
Another important value is AS PARNUM 223 which should be 7.

 

[kondalisa]

I will test these setting and gets back if problem not solved
Regards

 

[Satellite1900]

Hi,
try whit
on RODAI set VARC 00000350 VARI 50040000 VARO 06C000E0
on ROCAI set SERV 2110000001 SIG 511110100031
I'm waiting news....
Regards

 

[kondalisa]

Thanks very much all. I got CLI working now, Mundus advice did the trick. Ericsson tech config as mundus advice and CLI is now OK.
regards

 

[kondalisa]

Hi All, one more thing still need your help, I get the CLI number from ericsson PBX but name is still not showing on Nortel extension, i mean only number is displaying as CLI further Ring Again/Call Back feature is also not working, the ericsson tech says that the all commands which Mundus advised is not applicable on that Ericsson MD110, he executed only 2 commands i think that were command number 1 and 3. after that CLI number is showing but name and RIng AGain is not working, further ericsson tech also says that the commands which satellite900 pointed is not applicable or not for CLI name display.
I will really appreciate if you help further to get Name display of ericsson ectension works with Call Back feature.
Regards

 

[mundus]

to be sure, could you post: RODAP, ROCAP and relevant RODDP and ASPAPARNUM=223;