Norstar 0x32 T1 Installation question

[tomlinsonm]

Can someone help? Installing a T1 on an 0x32. What are the line settings etc, it has been years since I did a T1 turnup
Thank you,
Mt

 

[curlycord]

http://www.tek-tips.com/faqs.cfm?fid=1646

=----(((((((((()----=
curlycord

http://www.curlycord.com

 

[tomlinsonm]

Thanks Curlycord for thw reply - This did help a bunch! I think I now have all the settings but I have another question:
Comcast are not turned up yet but have their Adtran in place and I am connected. I have a flashing gerrn light on my T1 card (maybe thats a good sign? But when I try and press intercom and dial 9 it says "no lines available"???
I put all the lines in PRIA line pool etc....
Thanks

 

[hawks]

Do you have a Service or COMBO Card is the system?

 

[tomlinsonm]

A combo card in slot 2 (left to right)and my T1 card in slot 3

 

[exsmogger]

The green light will flash until the card has a live circuit to sync up with.

Brian Cox
Oregon Phone

http://www.OregonPhone.com

http://www.linkedin.com/in/briancox1952

 

[tomlinsonm]

Thanks Brian - but what about when I go intercom - dial 9 for an outside line and it says "no lines available"? Is that also because it cant grab a channel and so it kicks me back?
Thanks guys for all your help

 

[exsmogger]

Exactly. No channels are available to dial out yet, hence the error message.

Brian Cox
Oregon Phone

http://www.OregonPhone.com

http://www.linkedin.com/in/briancox1952

 

[curlycord]

Line 001 = PRI-A?
Dest Code 9 use a route?
Route uses PRI-A?
Set allowed PRI-A?
External Access code 9 removed?
Full 23 channel PRI or fractional?

outta ammo



=----(((((((((()----=
curlycord

http://www.curlycord.com

 

[hawks]

even with no circuit you should have a solid Green & Amber light. Check your programming & maybe disable and re-enable the card. If you press the Loop Back button on the card it should go Red and the Green light should start flashing.

 

[exsmogger]

I just noticed you put the T1 card in slot 3. That is actually card 2 in the MICS as the trunk cards go from right to left. Check to make sure you configured the correct card slot for your PRI.

Brian Cox
Oregon Phone

http://www.OregonPhone.com

http://www.linkedin.com/in/briancox1952

 

[exsmogger]

Hawks is correct. I was having a brain fart. When the slot is configured correctly the green lite will be on as well as the amber lite. When the circuit comes online the amber lite will go out.

Brian Cox
Oregon Phone

http://www.OregonPhone.com

http://www.linkedin.com/in/briancox1952

 

[tomlinsonm]

I think I am ready for the cut now, all seems to be looking good - thanks for your input guys

 

[tomlinsonm]

Ok, I have incoming working but still when I try and dial 9 for pool A it says "No lines available"
Line 001 = PRI-A
Dest Code 9 use a route 001
Route 001 uses PRI-A
Set allowed PRI-A
External Access code 9 removed
Full 23 channel PRI or fractional

I dont know where to go from here - except to say that it is Comcast - and should this still be a "wink-wink" situation even though it is PRI? I mentioned this to the cut tech and he said he never heard of this before!!

Thanks guys

 

[hawks]

Line 1 is PRI-A not Pool A change the information in you Route to PRI-A.

 

[tomlinsonm]

Sorry my mis type - it is all set to PRI-A, in my lines and in Route 001

 

[curlycord]

Maybe make sure no other lines are in PRI-A maybe?

=----(((((((((()----=
curlycord

http://www.curlycord.com