Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

No Video on IC7-Max3 Build!?! 1

Status
Not open for further replies.

joedammit

Technical User
Oct 4, 2005
9
US
System Spec's:
IC7-MAX3 Mobo
P4 3.0 prescott
2Gb Corsair (1GBx2)
2 250Gb maxtor sata HDD
Thermaltake 480 watt PSU
EVGA GeForce 6800cs Video Card

OK, I built the box, and when I start it up, I get no video or beeps. I have a watt display, and the power is surging like it is posting(140w surge then 100w running) Also when I shut down from the power button in the front, it takes 5-7 sec. to shut down, like it was running. All parts are know good.(pulled from running PC) The only variable is proc. but that is new. Any help welcome, Thanks.
 
Try a different monitor, or connect yours to a different system.
If there's a display on another monitor, or if there's no display on yours, then replace your monitor.

If the monitor is ok, then install/connect only the power supply, MB, CPU, memory, video card, monitor, keyboard, case speaker, and power button, and make sure the power supply's voltage selector switch is set to the correct voltage and the PS connection to the MB is securely seated.

If there's no display, then clear CMOS with a MB jumper, or by removing the CMOS battery for at least 30 minutes.
If that's already been done, then make sure the 'Clear CMOS' MB jumper is not in the 'Clear' position.
If the jumper is in the proper position, then check the CMOS battery for the correct voltage(3V).

If no luck, then place the MB on a piece of cardboard. If there's now a display, then the MB is shorting out when installed in the case. Check for a loose screw, standoff, etc., inside the case, and also remove any standoffs which do not line up with MB holes. If none is found, then remove all MB screws and metal standoffs, and install paper washers(manila folder paper works good for this) between the MB and the screws/standoffs.

If there's no display with the MB placed on a piece of cardboard, then proceed with the following:

(1)If the MB standby LED does not light up when you turn on the power supply's switch, then check the wall outlet, surge arrestor, and power cord for the correct voltage.
(2)If the voltages are ok for the items in (1) and the MB standby LED still does not light up, then then slightly raise the PS main power connector out of the MB connector a little. If the MB LED lights up, then the connector on either the PS or the MB is bad. If the MB light still does not come on, then the PS or MB is bad. Swap these 2 items out to find which one is bad.
(3)If MB light comes on, but the PS fan, other fans, and other lights do not work when the 'Power On' button is pushed, then make sure the computer case power button's wires are securely connected to the correct MB terminal(POW-ON, Power On, etc.), and that the wires are not shorting out(bare spots). If that's ok, then remove the power button's wires from the terminal, and momentarily short out the MB terminals with a screwdriver. If the fans and lights now work, then the 'Power On' button assembly is bad.
(4)If the fans connected to the MB and all other lights do not work when either the 'Power On' button is pushed or the MB 'Power On' terminals are shorted, then the MB or PS is bad. Swap them out.
(5)If all fans and lights work when the 'Power On' button is pushed but there's no display, then test the PS as described here:
If you do not have a voltmeter, then try a different PS.
(6)If the PS voltages are ok or there's no display with a different PS, then make sure the correct memory type is being used, remove and reinsert the memory a few times making sure it's firmly seated, install the memory modules one at a time in different slots, and make sure the video card is firmly seated(some video cards need an extra firm push to seat properly). If still no display, then swap out the MB, CPU, memory, and video card to find out which one is defective.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top