NO outbound on PRI w NI2

[viper222]

I just installed a TMDI PRI card on an Opt11c with NI2 signaling. I can receive inbound calls ok with CID, but when I try to call out it gives me a all trunks busy IE: Ring again? Does anyone have a clue why or where to start?

 

[PERRYPJ]

If you status the T1 in LD 60, what do the trunks look like

OLD ROLMEN WORKING ON NORTELS

 

[Reusser]

Also - give us a look at your route

You can also turn on dchannel messeges and that might give you a clue why the call is rejected.

 

[viper222]

Here is the Route and a trunk

LD 16 RDB

REQ: PRT
TYPE RDB
CUST 00
DMOD
ROUT 2
DES PRIT1
TKTP DID
NPID_TBL_NUM 0
SAT NO
IDEF NET
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 3
SBN NO
NCNA YES
NCRD NO
CHTY BCH
CPFXS NO
HNTN
HLCL
CPUB OFF
DAPC NO
BCOT 0
INTC YES
DSEL VOD
PTYP PRI
AUTO NO
DNIS YES
NDGT 4
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 8702
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DNAM NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
PAGE 002
NBS 2048
NBL 4096
TFD 0
DRNG NO
CDR NO
MUS NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

LD 14 Trunk

REQ: PRT
TYPE: TNB
TN 8 1
DATE
PAGE
DES
DES PRIT1
TN 008 01
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 3
RTMB 2 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND WTA LPR APN THFD HKD
P10 VNL
TKID 0001
DATE 30 APR 2003

 

[viper222]

STRANGE THING: I noticed that if I put a number in the System Speed Call List I can use it via the list and it will dial out correctly

Here is what I believe to be important info and to me honest I am just guessing on LD 15 NET_DATA

LD 17 CFN
D-CH of PRI

ADAN DCH 10
CTYP TMDI
CARD 08
PORT 1
DES PRI8
USR PRI
DCHL 8
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP
MBGA NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSERV YES
BSRC 2

LD 15 CDB
FTR and NET data

FTR_DATA
**DAPC**PREFIX TABLE NO: 00 **
UNKN**INTL**NATL**ESPN**LOCL**ELOC**ECDP**
UNKN*
E164* 00 0
PRIV*
E163* 00 0
TELX*
X121*
NATL*
OPT AHD BIND BIXA BLA CFO CFRA
COX CPA CTD DBD DNX DSX
HTU HVA XBL IC1 IDP XLF
IHD XTG FKA LOD LRA MCI
MWUD PVCD REA RNA
RTR RTA ROX SBD SYD
TTAD VOBA CWRD HLPD HRLD
CXOD
DGRP 10
IRNG NO
PKND 2
DNDL NO

NET_DATA
OPT RTA
AC2 LOC
FNP YES
ISDN YES
PINX_DN
MBG 0
BSGC 65535
PFX1 727
PFX2 570
HLOC 727
LSC 570
RCNT 5
OCLI NO
TRNX NO
EXTT NO
FTOP FRES
VNR NO
NIT 8
FOPT 14

 

[Reusser]

1- are you sure the other end is NI2

2- if the other end is an ATT switch ie dms250, change CO_type to ATT

3- how are you dialing out? Do you need to drop the 1?
Turn on dchannel messages
LD 96
enl msgi 10
enl msgo 10

watch the messages for the call setup to veryfy number going correctly with corect dial plan.
also look for disconnect reason.

4- work closely with the telco provider - they could also tell you why the call is being rejected. Once you know why you can take steps to correct.

 

[iptuser]

You said you can dial out vis a system speed call list ok, the system call list overcome the call barring are you sure it isn't something to do with barring, I noticed you have NCOS 3 in the Route

wayne

 

[PERRYPJ]

THE NCOS IN THE RDB ONLY EFFECTS INCOMING

OLD ROLMEN WORKING ON NORTELS

 

[viper222]

I found out what I did. As you know with PRI T-1's some of the changes you make force you to out the route and rebuild it the way you want it. I had taken the TARG 01 out because all of my phones use a TGAR of 1. Well, when I built it back I forgot to remove this so all of my phones could not use that route until I removed the TARG from the route. The system speed dial is set to bypass restrictions so thats why it worked with speed Dial. Sometimes I look to deep into things I overlook the obvious. Thanks for the suggestions though.