night option problem 1

[OKACHA]

Hello ;
I have a hipath 4000 v6 with ACWIN attendant and analog CO line, when I switch all the attendants (3900&&3904) to Night option for the STNO= 3000 and make a call with this station to external line the called party receive private number. If the attendant is activated and I make a call the CO number line is displayed on the called phone.
Best regards
Okacha

 

[adibv]

Hi.
STNO 3000 is an analog device or ?
I assume that SSTNO=NO in SCSU/SBCSU (secret station number).
An also LODR for outg call over CO is set to NPI,NATIONAL/INTERATIONAL and not UNKNOWN/UNKNOWN.
Do you have ACWIN/AC4 configured via ACSU ?
If yes, check in with AMO ACSU param. SATNDNO (secret AC number)=NO.
Check also if there is somethnig set up for param. PUBNUM in SDAT of NOPT stn 3000 and in ACSU.

 

[OKACHA]

there is no pubnum in stno 3000 and acsu . SSTNO WAS NO AND I HAD CHAGE IT TO YES BUT SAME PROBLEM
ADD-LODR:1,,,,OUTPULSE,0;
ADD-LODR:1,,,,ECHO,2;
ADD-LODR:1,,,,ECHO,3;
ADD-LODR:1,,,,END;
DISPLAY-ACSU:ATNDNO=3900;
DISPLAY-ACSU:ATNDNO=3900;
H500: AMO ACSU STARTED
+--------------------------------------------------------------+
| ASSIGNED DATA FOR ATTENDANT TERMINAL |
+----------+------------------------++--------+----------------+
| ATNDNO | 3900 || ACTYPE | ACW2QIP |
| ===== || ATNDGR | 0 |
| --------------------------------- || PEN | 1- 4- 79- 0 |
| SRCGRP | ( 1)|| NNO | 1- 10-102 |
| DPLN | 0 || SPDC1 | |
| COS | 1 || SPDC2 | |
| LCOSV | 41 || LANG | FRE |
| CLASSMRK | G711 EC || EOVR | NO |
| | G729AOPT || SATNDNO| NO |
| PUBNUM | || | |
| TON | || | |
| NPI | || | |
| STNOOOS | || | |
| STNOAPE | || | |
| AMOALTRT | NO || CLUSTID| 0 |
| DMCALLWD | NO || IPCODEC| G711P |
| IPPASSWD | || HMUSIC | 0 |
| CLASSSEC | SECURE || IPADDR | 10. 2.207. 30 |
+--------------------------------------------------------------+
<DISPLAY-SDAT:STNO=3000;
DISPLAY-SDAT:STNO=3000;
H500: AMO SDAT STARTED

---------------------------- SUBSCRIBERDATA ----------------------------
STNO = 3000 COS1 = 1 DPLN = 0 SSTNO = YES
PEN : 1- 1- 91- 0 COS2 = 1 ITR = 0 TRACE = NO
DVCFIG : OPTIP500 LCOSV1 = 41 COSX = 0 ALARMNO = 0
AMO : SBCSU LCOSV2 = 41 SPDI = 0 RCBKB = NO
LCOSD1 = 1 SPDC1 = RCBKNA = NO
KEYSYS : NO LCOSD2 = 1 SPDC2 =
------------------------------------------------------------------------
CDRACC =
SRCGRP = ( 1) TCLASS =
CLASSMRK = EC G711 G729AOPT
PUBNUM = TON = NPI =
NNO = 1 -10 -102 HOTIDX =
STNOOOS = MVHFAIP = NO
STNOAPE = AMOALTRT = NO
GWIPADR : CLUSTID =
SVCDOM =
PRECLEV =
BWLIDX =
CLASSSEC = TRADITIO
SECONLY =
------------------------------- ATTRIBUTES -----------------------------

------------------------------------------------------------------------

AMO-SDAT -111 ADMINISTRATION OF SUBSCRIBER ATTRIBUTES AND DATA
DISPLAY COMPLETED;

 

[adibv]

SSTNO in SDAT must remain to no.
Only H4k traces can tell us in which format the calling party number 3000 is sent over CO in both cases:
- good case : when call is made directly over CO from stn. 3000
- bad case : when call is made over CO from NOPT/NAVAR 3000 .
It might be that this is worked as designed. A NOPT is not intend to make calls from it, but only to receive.
Or maybe there is a correction in newer SW versions.

Additionally you may test the following scenario :
Activate NOPT on 3000.
Activate a CFU from 3000 to an external number/mobile.
Make a call from intern/extern to 3000 and check on the called pty. display (external number/mobile) what is shown on display (3000 or private)
Also for this a Trace would help.

 

[OKACHA]

thank you very much adibv

 

[adibv]

One more thing to check:

Check in ZAND: LCR, the value of LCRNSTN
LCRNSTN defaults to 0 and must be set for all ITR groups:

CHANGE-ZAND:TYPE=LCR,LCRNSTN=1&&10,XLCRNSTN=ADD,ITR=0;

DIS-ZAND:LCR;
LCR SETTINGS:
=============
ITR = 0
LCRCOSUP = 0
LCRNSTN = 1 ,2 ,3 ,4 ,5 ,6 ,7 ,8 ,9 ,10

If the field ITR is not specified, then the LCRNSTN Authorizations will be assigned for all ITR groups, 0 to 15.