Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Night button question 3

Status
Not open for further replies.

clarke123

IS-IT--Management
Sep 23, 2002
21
US
How do you set up a night button? 0x32 with Flash and AA is set up on time of day. I tried using F871 on the control set and it says "Denied in admin"
 
feature **266344,266344 go to services and make the set dn that you're trying to put the night button on, a control set under common settings, the do your feature * 3 press a blank button and do feature 871
 
To add to that, make sure you program your night ringing under Services. IE... which lines belong in which ringing group, does it come on automatically or manually, etc.
 
From a previous post:

PROGRAMMING MANUAL NIGHT SERVICES
The following settings will enable the attendant (receptionist) to answer all calls during the day, these calls will ring at this station until answered. At night the attendant will press the NIGHT SVC button and the AA will then answer the lines. (Note: Change the control set for each DID trunk and all target lines to 'none'. By default these are set to port 101's DN - usually 221.)
ENTER THE TELEPHONE SYSTEM PROGRAMMING:
Note: All incoming lines should appear and ring at the attendant station.
TERMINALS & SETS
Select NEXT to SERVICES, show, RINGING SERVICES, show, RINGING GROUP, show. Enter 01 for the Ringing Group. Press SHOW. At the SHOW SET prompt select SCAN. If any extension such as default 221 is ASSIGNED you must UNASSIGN it. Then Press FIND. At the SHOW SET prompt enter the first station port of the voicemail. Do not assign any other ports, just the first port. This can be found by enter FEATURE 985 which displays the first voicemail port.
Go back to RINGING GROUP and NEXT to SCHEDULE: NIGHT, and select SHOW.
Service should be set to MANUAL (The default is OFF). Then press NEXT to TRUNK ANSWER makes sure it is set to YES.
Then select HEADING and return to SERVICES and SHOW. Press NEXT to COMMON SETTINGS, press SHOW. At the prompt CONTROL SET, select SHOW. Make sure that the Control Set for each line is set to the extension you want to have the night button.
Program Night Button
Then go to the control extension. Press FEATURE * 3; press an available button, dial the night service FEATURE 871.
FLASH PROGRAMMING:
Note: the greetings should be recorded and assigned to the table as you wish.
Feature 983 and log in. Go to AA then LINES. SHOW the line 001. Then press TABLE, then RINGS. Make sure each line is set to 0 rings.
Then go into Feature 982 and log in using OPERATOR as the password. ATTENDANT AVAILABLE: Y, BUSINESS OPEN: Y, ANSWER LINES: N, ATDT (none), change this to the attendant extension.
If you would like the Auto Attendant to pick up unanswered lines during the day you will need to set the DRT (delayed ring transfer) TO PRIME to YES and the PRIME SET to the first port of the voice mail as per the following instructions.
TELEPHONE SYSTEM PROGRAMMING:
TERMINALS & SETS
NEXT to SYSTEM PROGRAMMING, SHOW. Press NEXT to FEATURE SETTINGS, SHOW. Then press NEXT to DRT to PRIME. Set to (Y)es. Press NEXT and set the DRT Ring Delay.
Use your header button to back up to TERMINALS & SETS. Press NEXT to LINES, SHOW. Show line 001. TRUNK LINE DATA, SHOW. Press NEXT to PRIMESET: 221. Change the PRIMESET to be the first port of the voice mail. You will need to change the PRIMESET on each of the lines individually.
Now outside calls will ring the attendant’s phone. In the event that the attendant cannot pick up the call within the ring parameter set in DRT to prime, the AA will then answer the call. At night when the attendant leaves, they will press the previously programmed Night Service button and the lines will be answered immediately by the automated attendant.


PhM










 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top