New PRI no forwarding or transfer to call pilot

[RossV]

I installed three new PRI's in my CS1KE on 5.5. I have test numbers on the new PRI's that I can IDC to my extension and they work as they should, however, when the call forward no answer or hunt kick over I hear the transfer ring but never get to voicemail. I tried to transfer a call to another extension from the same test numbers and the calling party gets cut off. Here's my RDB/Trk and dchannel build. The NCOS/Routes and IDC tables are working on the current t1's so I know they aren't the issue and I wouldn't be able to answer the IDC calls on the test numbers if they weren't routing the correct number of digits: The trunks and dchannels are up and running clean:

TYPE: rdb

CUST 0

ROUT 0


TYPE RDB
CUST 00
ROUT 0
DES ATT_LOCAL_ISDN
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
IDEF NET
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ESS5
SBN NO
PNI 00001
SRVC NNSF
NCNA YES
NCRD YES
CHTY BCH
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
MBXR NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS YES
NDGT 4
DDLY NO
DCDR NO
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD 5400
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DNAM NO
ICIS YES
TIMR ICF 384
OGF 384
EOD 4096
NRD 10112
DDL 70
ODT 2048
RGV 640
FLH 510


PAGE 002

GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST YES
QREC NO
OAL YES
AIA YES
OAN YES
OPD YES
CDRX NO
NATL YES
VRAT NO
MUS YES
MRT 30
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR YES
ASID 16
SFNB
USFB
CALB 7 8



DES QWEST_LOCAL
TN 118 01 VIRTUAL
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 5 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA HPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE 7 AUG 2009

ADAN DCH 68
CTYP TMDI
MG_CARD 012 0 03
PORT 1
DES Qwest3
USR PRI
DCHL 122
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE ATT
SIDE USR
CNEG 1
RLS ID 1
RCAP COLP NDS
MBGA NO
OVLR NO
OVLS NO
T310 120
INC_T306 2
OUT_T306 30
T200 3
T203 10
N200 3
N201 260
K 7
BSRV YES
BSRC 2

 

[edkender]

I assume the Callpilot is up and running. Can you call Cp and does it pick up? Also this looks like a 1000 E. Is the Cp in a differant Media Gateway? If it is are the dsp's working? Just a few things.

 

[johnpoole]

try changing vsel to vod, slim chance.. it might be ncos 0 on 118 1, depending on what ncos is defined as..

enl msgi on the inbound d, that may show a cause code for the non fdn

what happens if you hard forward a phone? can you dial your vsdn from a did?

john poole
bellsouth business
columbia,sc

 

[PERRYPJ]

What extension do you have for the mailbox the test or yours

OLD ROLMEN WORKING ON NORTELS AND AVAYA

 

[RossV]

Call pilot is fine I'm using an IDC table to send the call to my working extension. My phone rings and then it stops ringing as though the call went to voice mail however the caller continues to hear ring back and never gets to voicemail.

 

[allenmac]

Try setting NCNA and NCRD to NO in your RDB. I have seen these settings give LECs fits. They send D-Channel messages if the call is diverted, and can be mis-interpreted by the CO switch.