Networking bcm400 <-> Succ3.0

[LJDirk]

Hi,

i have installed MCDN Networking over PRI with BCM400 and Opt11.
When -120 (11c) call -240 (BCM) it works fine.
When -240 (BCM) call -120 (11c) it don´t work.

With the BCM Monitor i have make a Screenshot:

I think the cause: "massage not compatible with call state" is the problem, but i don´t know, where can I find a solution.
any things about that? THX

 

[SupportDude]

Where are you located?
I see in the setup message you're using G711 A-law.
North America uses u-law.

Here is the definition of the cause code:
Cause No. 98 - message not compatible with call state or message type non-existent or not implemented.
This cause indicates that the equipment sending this cause has received a message such that the procedures do not indicate that this is a permissible message to receive while in the call state. or a STATUS message was received indicating an incompatible call state.

This is typically a protocol issue.

HTH!

SD

 

[LJDirk]

thank you for replay.

I´m lokated in germany. A-Law is normal, not the problem.
I know the definition from the cause, because i don´t know where or what ist the wrongdoer.

 

[3Sixty]

Have you some info on the config for the option 11c and the BCM.

Setup of the 11c d channel and route.

http://www.nortelsupport.net

 

[LJDirk]

hi there,

on the BCM the programming is follow:

the Dest.Code "11X" and "12X" are ext. on Opt11
the 24x are ext. on the BCM

and on the opt11 is:

--------------------------[u]NET Data[/u]
TYPE NET_DATA
CUST 0
TYPE NET_DATA
CUST 00
OPT RTA
AC1 NPA LOC
AC2 INTL SPN NXX
FNP YES
ISDN YES
  VPNI 0
  PNI 1
  PINX_DN
  MBG 0
  BSGC 65535
  PFX1
  PFX2
  HLOC
  LSC
  RCNT 5
  PSTN NO
  TNDM 15
  PCMC 15
  SATD 1
  OCLI NO
TIDM NO
DASC
ROPT NRO
DITI YES
TRNX YES
EXTT YES
FTOP FRES
APAD 0  0
VNR NO
NIT 8
NAS_ATCL NO
NAS_ACTV NO
FOPT 14
CNDN
CNAT
CNIP YES
DMWM NO
MWNS NO
CNTC
NATC
INTC
---------------------------[u]D-Channel[/u]
REQ  prt
TYPE adan dch
ADAN     DCH 11
  CTYP MSDL
  CARD 01
  PORT 1
  DES  MCDN-BCM
  USR  PRI
  DCHL 1
  OTBF 80
  PARM RS422  DTE
  DRAT 64KC
  CLOK EXT
  NASA NO
  IFC  SL1
  SIDE NET
  SEMT 1
  CNEG 1
  RLS  ID  3
  RCAP ND2
  MBGA NO
  OVLR YES
  DIDD 0
  OVLS YES
  OVLT 0
  T200 2
  T203 20
  N200 3
  N201 260
  K    7
---------------------------[u]TIE-Route[/u]
REQ: prt
TYPE: rdb
CUST 0
ROUT 6
TYPE RDB
CUST 00
DMOD
ROUT 6
DES  MCDN-BCM
TKTP TIE
NPID_TBL_NUM   0
ESN  YES
RPA  NO
CNVT NO
SAT  NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
    MODE PRA
    IFC  SL1
    PNI  00001
    NCNA YES
    NCRD NO
    CTYP UKWN
    INAC NO
    ISAR NO
    DAPC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 9406
TCPP NO
TARG
BILN NO
OABS
INST
IDC  NO
DCNO 0 *
NDNO 0
DEXT NO
SIGO ESN5
MFC  NO
ICIS YES
OGIS YES
TIMR ICF  0
     OGF  512
     EOD  10112
     NRD  10112
     DDL  70
     ODT  4096
     RGV  640
     GTO  2048
     GTI  1280
     SFB  3
     NBS  2048
     NBL  4096
     IENB  5
     TFD  0
     VSS  0
     VGD  6
DTD  NO
SCDT NO
2 DT NO
DRNG YES
NDRI 02
CDR  NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS  YES
MRT  10
PANS YES
RACD NO
FRL  0 7
FRL  1 7
FRL  2 7
FRL  3 7
FRL  4 7
FRL  5 7
FRL  6 7
FRL  7 7
OHQ  NO
OHQT 00
CBQ  NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
OPR  NO
ALRM NO
ART  0
PECL NO
DCTI 0
TIDY 9406 6
SGRP 0
AACR NO
---------------------------[u]Steering Code -240[/u]
REQ  prt
CUST 0
FEAT cdp
TYPE dsc
DSC  240
DSC  240
FLEN 3
DSP  DN
RRPA NO
RLI  6
NPA
NXX
---------------------------[u]Route List Block[/u]
REQ  prt
CUST 0
FEAT rlb
RLI  6
RLI  6
ENTR 0
LTER NO
ROUT 6
TOD  0 ON  1 ON  2 ON  3 ON
     4 ON  5 ON  6 ON  7 ON
VNS  NO
CNV  NO
EXP  NO
FRL  0
DMI  6
FCI  0
FSNI 0
BNE NO
SBOC NRR
IDBB DBA
IOHQ NO
OHQ  NO
CBQ  NO
ISET 0
NALT 5
MFRL 0
OVLL 1
---------------------------[u]Digit Revaluation[/u]
REQ  prt
CUST 0
FEAT dgt
DMI  6
DMI  6
DEL  0
CTYP UKWN

 

[3Sixty]

Try putting the parameter Nam against the D channel and see if that fixes your problem. Either that or try switching of send name display on the BCM.

Marshall

http://www.nortelsupport.net

 

[3Sixty]

Forgot to ask what version of BCM?

http://www.nortelsupport.net

 

[subx]

its BCM 3.7 on a BCM 400 ;O)

 

[LJDirk]

- upgradet from 2.5

and these Patches are installed:

ASN1Update 06/17/2004 4:19p
SSM_36001111 06/28/2004 12:17p
BCM_360.092_RCC.61.044 12/14/2004 3:36p
BCM_370.105_CORE.08.0708 03/14/2006 7:49a
BCM_370.103_FEPS.33.371700 03/14/2006 10:37a

i hope that the Core Patch fix it, but not real.

 

[LJDirk]

without name is the same problem

 

[3Sixty]

What is your meridian extension range?

Marshall

http://www.nortelsupport.net

 

[3Sixty]

What is you signaling server version?

Marshall

http://www.nortelsupport.net

 

[3Sixty]

I have a doc regarding BCM interop issues might be worth a look rather than me asking question after question.

Marshall

I will put it on my site if you need the info.

http://www.nortelsupport.net

 

[subx]

would be fine if u put it on ur site so we can have a look... extension range is 1xx... we dont have right now signaling server... its simple standard MCDN PRI connection...

regards,

subx

 

[3Sixty]

Why are you sending 103120 if your extension range is 120?

Marshall

http://www.nortelsupport.net

 

[LJDirk]

the opt11 send 103240 when i make a call to the BCM.
I think it´s normal for MCDN:

1 = PNI
0 = Customer
3 = NCOS
240 = ext. on the BCM

I send this Information from the BCM (in the Route - ext. Number) to the Succ. Then the ext. -120 ring only one time and the Cause Massage comes.
When I send not the Tel. will not ring.

 

[LJDirk]

1. Info - now I have inst. the BCM_370[1].110_CUMULATIVE.99.1 Patch an it´s the same Prob.
2. Info - with NCOS 7 the same (107120)

 

[3Sixty]

Are you sure the meridian is striping off the incoming info. I would try a straight pool access and dial the extension number and see if you have the same problem.

Marshall

http://www.nortelsupport.net

 

[LJDirk]

with the straight access (without 103) the Telefon -120 will not ring.
The cause in this case is the same.

 

[3Sixty]

Have you switched on the messaging on the D channel on the meridian to see what is being presented on the meridian side.

Marshall

http://www.nortelsupport.net