Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations gkittelson on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Networked magix problem

Status
Not open for further replies.

techman63

Programmer
Aug 20, 2004
47
US
I have 3 networked magix systems (main system and one remote office are R4 and another one is R2.2) with point to point PRI,set as UDP ,the internal calls between remote sites and main sites works both way and also centralized VM works .The main system has 3 PRI cards ,2 for the PTP and one for Outgoing calls.
My problem is I can’t make any outside call from the remote site through the main site and the remote sites can’t call each other through the main site. The main site dial fine on the PRI using the ARS tables 25&26 with FRL 0.
I set remote sites with simple ARS table 25&26 use the POOL for the PRI links and FRL is set to zero and Added digits 9 in subA digits, 9 is the ARS code is the main location .I get a reorder tone when I try to dial any number from the remote locations and the Yellow light flash for second on the PRI card.
I set under lines and trunks Remote access, NO restriction, no barrier codes and FRL is set to 0 for all Tie and NON tie lines. And all extensions have FRL 3.LS disconnect is set to yes.
What I’m missing, any help I much appreciated.
 
I would need some print outs first before I could even begin. I would say print the ARS tables between the main site and 1 remote site. The PRI info at both sites(Main and 1 remote). The remote access at both sites. This would start to give us a clearer picture as to what could be going on.
 
LS disconect is programmed to yes.
Remote access lines Tie &NON tie is set with no rest,NO Barrier code and FRL 0.
The ARS is only table 25 and table 26 ,no other table is used and they programmed to use the POOL for the PRI link and FRL is set to zero and SUB A digits I have 9 for the ARS code of the main system.
 
Here are the Print from the main system PRI &ARS
PRI INFORMATION



Slot 3 Switch: 5ESS

Slot 6 Switch: MERLIN-Ntwk

Slot 7 Switch: MERLIN-Ntwk

System: By extension Base number:

BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
1 3 CallbyCall By Dial Plan

Channel ID: 5 6 8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23 7 1
2 3 4

Line PhoneNumber NumberToSend
805
806
807
808
809
810
811
812
813
814
815
816
818
819
820
821
822
823
824
825
826
827
828

BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
78 6 ElecTandNtwk Route Directly to UDP

Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1

Line PhoneNumber NumberToSend
829
830
831
832
833
834
PRI INFORMATION


835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851

BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
79 7 ElecTandNtwk Route Directly to UDP

Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1

Line PhoneNumber NumberToSend
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875

BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
80 6 ElecTandNtwk Route Directly to UDP

Channel ID:

Line PhoneNumber NumberToSend
PRI INFORMATION


852

Network Selection Table

Entry Number: 0 1 2 3
Pattern to Match: 101**** 10***

Special Service Table

Entry Number: 0 1 2 3 4 5 6 7
Pattern to Match: 011 010 01 00 0
Operator: none OP OP OP/P OP none none none
Type of Number: I I I N N N N N
Digits to Delete: 3 3 2 2 1 1 0 0

Call-By-Call Service Table

Entry Number: 0 1 2 3 4
Pattern 0: 0
Pattern 1: 1
Pattern 2: 2
Pattern 3: 3
Pattern 4: 4
Pattern 5: 5
Pattern 6: 6
Pattern 7: 7
Pattern 8: 8
Pattern 9: 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ: No Service No Service
DeleteDigits: 0 0 0 0 0

Entry Number: 5 6 7 8 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ:
DeleteDigits: 0 0 0 0 0

Dial Plan Routing Table

Entry Number: 0 1 2 3
NtwkServ: Any service
Expected Digits: 4 0 0 0
Pattern to Match:
Digits to Delete: 2 0 0 0
Digits to Add: 1

Entry Number: 4 5 6 7
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 8 9 10 11
NtwkServ:
PRI INFORMATION


Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 12 13 14 15
NtwkServ: Any service
Expected Digits: 0 0 0 4
Pattern to Match: 4021
Digits to Delete: 0 0 0 4
Digits to Add: 100



AUTOMATIC ROUTE SELECTION


ARS IS: ACTIVE ACCESS CODE: 9


TABLE 25: Default Toll Output Table

Pool Absorb Other Digits FRL Call type Start Pattern
1)890- 00 -------------------- 0 BOTH --:-- A
2)890- 00 -------------------- 0 BOTH --:-- A
3)---- -- -------------------- - ----- --:-- A
4)---- -- -------------------- - ----- --:-- A
5)---- -- -------------------- - ----- --:-- A
6)---- -- -------------------- - ----- --:-- A

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 3 BOTH --:-- B
2)---- -- -------------------- - ----- --:-- B
3)---- -- -------------------- - ----- --:-- B
4)---- -- -------------------- - ----- --:-- B
5)---- -- -------------------- - ----- --:-- B
6)---- -- -------------------- - ----- --:-- B
AUTOMATIC ROUTE SELECTION



TABLE 26: Default Local Output Table

Pool Absorb Other Digits FRL Call type Start Pattern
1)890- 00 -------------------- 0 BOTH --:-- A
2)890- 00 -------------------- 0 BOTH --:-- A
3)---- -- -------------------- - ----- --:-- A
4)---- -- -------------------- - ----- --:-- A
5)---- -- -------------------- - ----- --:-- A
6)---- -- -------------------- - ----- --:-- A

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 2 BOTH --:-- B
2)---- -- -------------------- - ----- --:-- B
3)---- -- -------------------- - ----- --:-- B
4)---- -- -------------------- - ----- --:-- B
5)---- -- -------------------- - ----- --:-- B
6)---- -- -------------------- - ----- --:-- B
AUTOMATIC ROUTE SELECTION



TABLE 27: Dial 0 Output Table

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 3 BOTH --:-- A
AUTOMATIC ROUTE SELECTION



TABLE 28: N11 Output Table
01)411 02)611 03)811

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 0 BOTH --:-- A
AUTOMATIC ROUTE SELECTION



TABLE 29: E911 Table (911)

E911 Option: Partition

Allow-11: Disable

Other Digits for E911 calls redirected to Main Pool: --------------------

E911 Adjunct Trunks:

E911 Adjunct Alarm Extension:

Partition 1:
Extensions: 100 7300 101 7301 102 7302 103 7303
104 7304 105 7305 106 7306 107 7307 108 7308
109 7309 110 7310 111 7311 112 7312 113 7313
114 7314 115 7315 116 7316 117 7317 118 7318
119 7319 120 7320 121 7321 122 7322 123 7323
124 7324 125 7325 126 7326 127 7327 128 7328
129 7329 130 7330 131 7331 132 7332 133 7333
134 7334 135 7335 136 137 138 139 140 141
142 143 144 145 146 147 148 149 7150 7151
7152 7153 7154 7155 7156 7157 7158 7159 7160 7161
7162 7163 7164 7364 7165 7365 7166 7366 7167 7367
7168 7368 7169 7369 7170 7370 7171 7371 7172 7372
7173 7373 7174 7374 7175 7375
Trunks:
Other Digits: --------------------

Partition 2:
Extensions:
Trunks:
Other Digits: --------------------

Partition 3:
Extensions:
Trunks:
Other Digits: --------------------

Partition 4:
Extensions:
Trunks:
Other Digits: --------------------

Partition 5:
Extensions:
Trunks:
Other Digits: --------------------

Partition 6:
Extensions:
Trunks:
Other Digits: --------------------

Partition 7:
Extensions:
Trunks:
Other Digits: --------------------

Partition 8:
Extensions:
Trunks:
Other Digits: --------------------

Partition 9:
Extensions:
Trunks:
Other Digits: --------------------

Partition 10:
Extensions:
Trunks:
Other Digits: --------------------



 
Unless the print got garbled, I see several things to check. Slot 3, 817 (BCH 13) is missing from the main PRI pool B channel group, and 828 which is the DCH 24 should NOT be in any pool or group. The same goes for slot 6, 852, the DCH 24 for the network PRI to one of your remote sites.

The DCH is the data channel on a PRI configuration. ALL signaling takes place on this channel, and is fixed in the system. No programming necessary. DO NOT PUT IT ANYWHERE!

....JIM....
 
Thanks for the reply.
I checked the program and no D chaneel was in any pools ,maybe it was just glitch in the print when I paste it.
 
You posted:

"Remote access lines Tie & NON tie is set with no rest,NO Barrier code and FRL 0."

It needs to be this way in all switches, not just the main site.

BTW, this is about as tricky as it gets in the way of programming on these systems.





 
I know and all systems has the same paramters.
NO rest ,no barrier code and FRL 0.
 
All the system the same like below:

REMOTE ACCESS (DISA) INFORMATION


GENERAL OPTIONS ACCESS CODE: 889

Barrier Code required for Non-TIE DISA lines: No
Barrier Code required for TIE DISA lines : No
Automatic Queuing enabled for DISA lines : No

SYSTEM DEFAULT CLASS OF RESTRICTIONS (NON-TIE)

Restriction : UNRESTRICTED
ARS Restriction Level: 0
Allowed Lists :
Disallowed Lists :

SYSTEM DEFAULT CLASS OF RESTRICTIONS (TIE)

Restriction : UNRESTRICTED
ARS Restriction Level: 0
Allowed Lists :
Disallowed Lists :


 

They are set for Legend PBX.
The dialing between each remote site to the main site is working fine, that’s why I'm puzzled .I’m very familiar with the networking on legend and magix however this one I don’t understand it why it’s working. I have the same setup on my lap and its working .I start to think maybe corrupt processor or something. I will keep digging and I will keep you posted with results if any. Thanks
 
Still not working but here are the updates.
I default the main system and reprogram it again and changed one of the remote system processor to R4 to match the main system and reprogram it again from scratch, but still I have the same results, I can dial from the remote sites to the main sites and vise versa but I can’t dial remote site to remote site, and The Important problem is I can’t dial any outside numbers from the remote site through the main PRI in the main site.
As temporary solution I had some spare T/R ports I looped back to some LOOP co and programmed it as remote access and from the remote sites I can dial the extension and get dial tone and dial 9 and I can dial out through the PRI on the main site,and no probelm this way ,it works.
So it looks to me that I have overlooked something somehow and I just need some fresh eyes if possible .I appreciates any suggestions. Here is again the dial plan with simple ARS and I also removed the centralized VM to make it simple just in case for the time been. Thanks.

The main site

PRI INFORMATION



Slot 3 Switch: 5ESS

Slot 6 Switch: MERLIN-Ntwk

Slot 7 Switch: MERLIN-Ntwk

System: By line

BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
1 3 CallbyCall By Dial Plan

Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1

Line PhoneNumber NumberToSend
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827

BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
79 7 ElecTandNtwk Route Directly to UDP

Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1

Line PhoneNumber NumberToSend
853
854
855
856
857
858
PRI INFORMATION


859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875

BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
80 6 ElecTandNtwk Route Directly to UDP

Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1

Line PhoneNumber NumberToSend
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851

Network Selection Table

Entry Number: 0 1 2 3
Pattern to Match: 101**** 10***

Special Service Table

PRI INFORMATION


Entry Number: 0 1 2 3 4 5 6 7
Pattern to Match: 011 010 01 00 0 1
Operator: none OP OP OP/P OP none none none
Type of Number: I I I N N N N N
Digits to Delete: 0 0 0 0 0 0 0 0

Call-By-Call Service Table

Entry Number: 0 1 2 3 4
Pattern 0: 0
Pattern 1: 1
Pattern 2: 2
Pattern 3: 3
Pattern 4: 4
Pattern 5: 5
Pattern 6: 6
Pattern 7: 7
Pattern 8: 8
Pattern 9: 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ: No Service
DeleteDigits: 0 0 0 0 0

Entry Number: 5 6 7 8 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ:
DeleteDigits: 0 0 0 0 0

Dial Plan Routing Table

Entry Number: 0 1 2 3
NtwkServ: Any service
Expected Digits: 4 0 0 0
Pattern to Match:
Digits to Delete: 2 0 0 0
Digits to Add: 1

Entry Number: 4 5 6 7
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 8 9 10 11
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 12 13 14 15
NtwkServ: Any service
Expected Digits: 0 0 0 4
Pattern to Match: 4021
PRI INFORMATION


Digits to Delete: 0 0 0 4
Digits to Add: 100







AUTOMATIC ROUTE SELECTION


ARS IS: ACTIVE ACCESS CODE: 9


TABLE 25: Default Toll Output Table

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 3 BOTH --:-- A
2)---- -- -------------------- - ----- --:-- A
3)---- -- -------------------- - ----- --:-- A
4)---- -- -------------------- - ----- --:-- A
5)---- -- -------------------- - ----- --:-- A
6)---- -- -------------------- - ----- --:-- A

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 3 BOTH --:-- B
2)---- -- -------------------- - ----- --:-- B
3)---- -- -------------------- - ----- --:-- B
4)---- -- -------------------- - ----- --:-- B
5)---- -- -------------------- - ----- --:-- B
6)---- -- -------------------- - ----- --:-- B
AUTOMATIC ROUTE SELECTION



TABLE 26: Default Local Output Table

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 3 BOTH --:-- A
2)---- -- -------------------- - ----- --:-- A
3)---- -- -------------------- - ----- --:-- A
4)---- -- -------------------- - ----- --:-- A
5)---- -- -------------------- - ----- --:-- A
6)---- -- -------------------- - ----- --:-- A

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 2 BOTH --:-- B
2)---- -- -------------------- - ----- --:-- B
3)---- -- -------------------- - ----- --:-- B
4)---- -- -------------------- - ----- --:-- B
5)---- -- -------------------- - ----- --:-- B
6)---- -- -------------------- - ----- --:-- B
AUTOMATIC ROUTE SELECTION



TABLE 27: Dial 0 Output Table

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 3 BOTH --:-- A
AUTOMATIC ROUTE SELECTION



TABLE 28: N11 Output Table
01)411 02)611 03)811

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 3 BOTH --:-- A
AUTOMATIC ROUTE SELECTION



TABLE 29: E911 Table (911)

E911 Option: Partition

Allow-11: Disable

Other Digits for E911 calls redirected to Main Pool: --------------------

E911 Adjunct Trunks:

E911 Adjunct Alarm Extension:

Partition 1:
Extensions: 100 7300 101 7301 102 7302 103 7303
104 7304 105 7305 106 7306 107 7307 108 7308
109 7309 110 7310 111 7311 112 7312 113 7313
114 7314 115 7315 116 7316 117 7317 118 7318
119 7319 120 7320 121 7321 122 7322 123 7323
124 7324 125 7325 126 7326 127 7327 128 7328
129 7329 130 7330 131 7331 132 7332 133 7333
134 7334 135 7335 136 137 138 139 140 141
142 143 144 145 146 147 148 149 150 151
152 153 154 155 156 157 158 159 160 161
162 163 164 7364 165 7365 166 7366 167 7367
168 7368 169 7369 170 7370 171 7371 172 7372
173 7373 174 7374 175 7375
Trunks:
Other Digits: --------------------

Partition 2:
Extensions:
Trunks:
Other Digits: -------------------¬.Æ~?~~~~~~A Extensions:
Trunks:
Other Digits: --------------------

Partition 4:
Extensions:
Trunks:
Other Digits: --------------------

Partition 5:
Extensions:
Trunks:
Other Digits: --------------------

Partition 6:
Extensions:
Trunks:
Other Digits: --------------------

Partition 7:
Extensions:
Trunks:
Other Digits: --------------------

Partition 8:
Extensions:
Trunks:
Other Digits: --------------------

Partition 9:
Extensions:
Trunks:
Other Digits: --------------------

Partition 10:
Extensions:
Trunks:
Other Digits: --------------------




REMOTE ACCESS (DISA) INFORMATION


GENERAL OPTIONS ACCESS CODE: 889

Barrier Code required for Non-TIE DISA lines: No
Barrier Code required for TIE DISA lines : No
Automatic Queuing enabled for DISA lines : No
System Wide Barrier Code Length : 07
Date and Time of Last Barrier Code Change : 01/01/00 12:00AM

SYSTEM DEFAULT CLASS OF RESTRICTIONS (NON-TIE)

Restriction : UNRESTRICTED
ARS Restriction Level: 3
Allowed Lists :

Restriction : UNRESTRICTED



NON-LOCAL DIALPLAN



Range Ptn Dgt Range Ptn Dgt Range Ptn Dgt
1) 250- 299 02 03 18) - 35) -
2) 400- 499 01 03 19) - 36) -
3) - 20) - 37) -
4) - 21) - 38) -
5) - 22) - 39) -
6) - 23) - 40) -
7) - 24) - 41) -
8) - 25) - 42) -
9) - 26) - 43) -
10) - 27) - 44) -
11) - 28) - 45) -
12) - 29) - 46) -
13) - 30) - 47) -
14) - 31) - 48) -
15) - 32) - 49) -
16) - 33) - 50) -
17) - 34) -

Pattern 1:

Pool Absorb Other Digits FRL Call type
1)898- 00 -------------------- 3 BOTH
2)---- -- -------------------- - -----
3)---- -- -------------------- - -----
4)---- -- -------------------- - -----

Pattern 2:

Pool Absorb Other Digits FRL Call type
1)899- 00 -------------------- 3 BOTH
2)---- -- -------------------- - -----
3)---- -- -------------------- - -----
4)---- -- -------------------- - -----



Remote site

PRI INFORMATION



Slot 3 Switch: MERLIN-PBX

System: By line

BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
80 3 ElecTandNtwk Route Directly to UDP

Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1

Line PhoneNumber NumberToSend
809
810
811
812
813
814
815
816
817
818
819
820
821
822
824
825
826
827
828
829
830
831
832

Network Selection Table

Entry Number: 0 1 2 3
Pattern to Match:

Special Service Table

Entry Number: 0 1 2 3 4 5 6 7
Pattern to Match: 011 010 01
Operator: none OP OP OP/P OP none none none
Type of Number: N I I N N N N N
Digits to Delete: 0 3 2 2 1 1 0 0

Call-By-Call Service Table

Entry Number: 0 1 2 3 4
Pattern 0: 0
Call Type: BOTH BOTH BOTH BOTH BOTH
PRI INFORMATION


NtwkServ:
DeleteDigits: 0 0 0 0 0

Entry Number: 5 6 7 8 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ:
DeleteDigits: 0 0 0 0 0

Dial Plan Routing Table
Expected Digits: 4 0 0 0
Pattern to Match:
Digits to Delete: 2 0 0 0
Digits to Add: 1

Entry Number: 4 5 6 7
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 8 9 10 11
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 12 13 14 15
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:





REMOTE ACCESS (DISA) INFORMATION


GENERAL OPTIONS ACCESS CODE: 889

Barrier Code required for Non-TIE DISA lines: No
Barrier Code required for TIE DISA lines : No
Automatic Queuing enabled for DISA lines : No
System Wide Barrier Code Length : 07
Date and Time of Last Barrier Code Change : 01/01/00 12:02AM

SYSTEM DEFAULT CLASS OF RESTRICTIONS (NON-TIE)

Restriction : UNRESTRICTED
ARS Restriction Level: 0
Allowed Lists :
Disallowed Lists :

SYSTEM DEFAULT CLASS OF RESTRICTIONS (TIE)

Restriction : UNRESTRICTED
ARS Restriction Level: 0
Allowed Lists :
Disallowed Lists :




AUTOMATIC ROUTE SELECTION


ARS IS: ACTIVE ACCESS CODE: 9


TABLE 25: Default Toll Output Table

Pool Absorb Other Digits FRL Call type Start Pattern
1)890- 00 9------------------- 3 BOTH --:-- A
2)---- -- -------------------- - ----- --:-- A
3)---- -- -------------------- - ----- --:-- A
4)---- -- -------------------- - ----- --:-- A
5)---- -- -------------------- - ----- --:-- A
6)---- -- -------------------- - ----- --:-- A

Pool Absorb Other Digits FRL Call type Start Pattern
1)890- 00 -------------------- 3 BOTH --:-- B
2)---- -- -------------------- - ----- --:-- B
3)---- -- -------------------- - ----- --:-- B
4)---- -- -------------------- - ----- --:-- B
5)---- -- -------------------- - ----- --:-- B
6)---- -- -------------------- - ----- --:-- B
AUTOMATIC ROUTE SELECTION



TABLE 26: Default Local Output Table

Pool Absorb Other Digits FRL Call type Start Pattern
1)890- 00 9------------------- 3 BOTH --:-- A
2)---- -- -------------------- - ----- --:-- A
3)---- -- -------------------- - ----- --:-- A
4)---- -- -------------------- - ----- --:-- A
5)---- -- -------------------- - ----- --:-- A
6)---- -- -------------------- - ----- --:-- A

Pool Absorb Other Digits FRL Call type Start Pattern
1)890- 00 -------------------- 3 BOTH --:-- B
2)---- -- -------------------- - ----- --:-- B
3)---- -- -------------------- - ----- --:-- B
4)---- -- -------------------- - ----- --:-- B
5)---- -- -------------------- - ----- --:-- B
6)---- -- -------------------- - ----- --:-- B
AUTOMATIC ROUTE SELECTION



TABLE 27: Dial 0 Output Table

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 3 BOTH --:-- A
AUTOMATIC ROUTE SELECTION



TABLE 28: N11 Output Table
01)411 02)611 03)811

Pool Absorb Other Digits FRL Call type Start Pattern
1)70-- 00 -------------------- 3 BOTH --:-- A
AUTOMATIC ROUTE SELECTION



TABLE 29: E911 Table (911)

E911 Option: Partition

Allow-11: Disable

Other Digits for E911 calls redirected to Main Pool: --------------------

E911 Adjunct Trunks:

E911 Adjunct Alarm Extension:

Partition 1:
Extensions: 400 7300 401 7301 402 7302 403 7303
404 7304 405 7305 406 7306 407 7307 408 7308
409 7309 410 7310 411 7311 412 7312 413 7313
414 7314 415 7315 416 7316 417 7317 418 7318
419 7319 420 7320 421 7321 422 7322 423 7323
424 425 426 427 428 429 430 431 432 433
434 435 436 7336 437 7337 438 7338 439 7339
440 7340 441 7341 442 7342 443 7343 444 7344
445 7345 446 7346 447 7347 448 7348 449 7349
450 7350 451 7351 452 7352 453 7353 454 7354
455 7355 456 7356 457 7357 458 7358 459 7359
Trunks:
Other Digits: --------------------

Partition 2:
Extensions:
Trunks:
Other Digits: --------------------

Partition 3:
Extensions:
Trunks:
Other Digits: --------------------

Partition 4:
Extensions:
Trunks:
Other Digits: --------------------

Partition 5:
Extensions:
Trunks:
Other Digits: --------------------

Partition 6:
Extensions:
Trunks:
Other Digits: --------------------

Partition 7:
Extensions:
Trunks:
Other Digits: --------------------

Partition 8:
Extensions:
Trunks:
Other Digits: --------------------

Partition 9:
Extensions:
Trunks:
Other Digits: --------------------

Partition 10:
Extensions:
Trunks:
Other Digits: --------------------
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top