Need help on Brooktrout setup for analog extensions from G3

[frl5633]

The user's fax extensions are set up as phantom extensions with coverage paths to a hunt group with 4 members that are connected to the Brooktrout TR114 Analog card. Calls come in via ISND/PRI and are sent to the hunt group via the coverage path. Problem is the fax server is not seeing the number being passed from the ISDN trunk group. Brooktrout support states that the PBX "Be able to send down the dialed number, or part of the dialed number to the port as DTMF digits after the call has been answered. This is commonly called 'after-dialing', and is a feature provided for the PABX to communicate with other peripherals, such as voice mail." I can't find where that feature would be.
Any thoughts?

 

[dufus2506]

If you have vectoring, use the 'converse-on' command.

You can converse-on the hunt group passing DNIS, ANI, VDN and a few other attributes.

Convert the extensions to VDN's and run them through a vector with the 'converse-on' command and you'll get the information you need passed to the Brooktrout card.

If you don't have vectoring, you might try connecting these as a trunk group rather than as stations. Analog trunks would outpulse the DNIS for you.

Carpe dialem! (Seize the line!)

 

[ohyes]

DISCLAIMER: The following BRI configuration has been used to connect the
Lucent PBX to the Brooktrout TR114 BRI card. This information should only be used
as a guideline and we strongly recommend that you contact your telephone
administrator or PBX vendor if you are planning to configure and change the switch
settings on your PBX, or if you have questions about any of the following settings.
Brooktrout Technology does not guarantee or warrant this information and it is not
assumed that the information is true or correct.
NOTE: Because of these configuration requirements, it maybe necessary to dedicate
the Lucent BRI card to fax server.
Command: disp bri 1b10
display bri-trunk-board 1b10
display bri-trunk-board 1b10 Page 1 of 2
ISDN-BRI TRUNK CIRCUIT PACK
Location: 01B10 Name: Fax Server
Interface Companding: a-law DCP/Analog Bearer Capability: 3.1kHz
Port Interface Side Cntry/Peer TEI Time Invert
Protocol Fill Bits?
1: network etsi 0 ones n
2: network etsi 0 ones n
3: 0 ones n
4: 0 ones n
5: 0 ones n
6: 0 ones n
7: 0 ones n
8: 0 ones n
9: 0 ones n
10: 0 ones n
11: 0 ones n
12: 0 ones n
display bri-trunk-board 1b10
display bri-trunk-board 1b10 Page 2 of 2
ISDN-BRI TRUNK CIRCUIT PACK
Port XID Endpt SPID Endpt Max
Test? Init? ID NCA TSC
1: n n 0
2: n n 0
3: n n 0
4: n n 0
5: n n 0
6: n n 0
7: n n 0
8: n n 0
9: n n 0
10: n n 0
11: n n 0
12: n n 0
display bri-trunk-board 1b10 Page 2 of 2
Command aborted
display bri-trunk-board 1b10
Command: disp tru 3
display trunk-group 3 Page 1 of 9
TRUNK GROUP
Group Number: 3 Group Type: isdn CDR Reports: y
Group Name: Fax Server COR: 1 TN: 1 TAC: 703
Direction: two-way Outgoing Display? n
Dial Access? y Busy Threshold: 99 Night Service:
Queue Length: 0
Service Type: tie Auth Code? n TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send TCM,Lookahead: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: c Digit Handling (in/out): overlap/overlap
Digit Treatment: Digits:
Trunk Hunt: cyclical
Connected to Toll? n STT Loss: normal DTT to DCO Loss: normal
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? y
Answer Supervision Timeout: 0
display trunk-group 3
display trunk-group 3 Page 2 of 9
TRUNK FEATURES
ACA Assignment? n Measured: none Wideband Support? n
Internal Alert? n Maintenance Tests? n
Data Restriction? n NCA-TSC Trunk Member:
Send Name: n Send Calling Number: y
Used for DCS? n Send Connected Number: y
Suppress # Outpulsing? n Numbering Format: unknown
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider
Send UCID? n
Send Codeset 6/7 LAI IE? y
display trunk-group 3
display trunk-group 3 Page 3 of 9
TRUNK GROUP
Administered Members (min/max): 1/4
GROUP MEMBER ASSIGNMENTS Total Administered Members: 4
Port Code Sfx Name Night Sig Grp
1: 01B1001 TN556 D
2: 01B1017 TN556 D
3: 01B1002 TN556 D
4: 01B1018 TN556 D
5:
6:
7:
8:
9:
10:
11:
12:
13:
14:
15:
display trunk-group 3 Page 3 of 9
Command aborted
display trunk-group 3
Command:

 

[gonzalez]

1.Make sure you have mode code turned on. (Depends on what release you have. Newer release's it is on the system parameters features and can be changed,on older release's you check it on Sysytem Parameters Customer options and can only be changed by Avaya.)
2. Set up the analog ports that plug into the Brooktrout card as Type VMI and put those in the hunt group of the coverage path for the Fax extensions

Mode code is also known as Inband Signaling.