Need help in creating multi Ars Table for DIFFERENT COR

[Arvindsunny]

I have 2 floors in my floor all the phone are reg in location 1

Want to create separate cor for 2nd floor (eg) cor 100 use to trunk 21

currently cor 3 access code ars 0 use trunk 1

I created cor 100 as test


COR Number: 100
COR Description: test

FRL: 0 APLT? y
Can Be Service Observed? n Calling Party Restriction: none
Can Be A Service Observer? n Called Party Restriction: none
Time of Day Chart: 8

​

Forced Entry of Account Codes? n
Priority Queuing? n Direct Agent Calling? n
Restriction Override: none Facility Access Trunk Test? y
Restricted Call List? n Can Change Coverage? n




display time-of-day 8

TIME OF DAY ROUTING PLAN 8

Act PGN Act PGN Act PGN Act PGN Act PGN Act PGN
Time # Time # Time # Time # Time # Time #


Sun 00:00 8 : : : : :
Mon 00:00 8 : : : : :
Tue 00:00 8 : : : : :
Wed 00:00 8 : : : : :
Thu 00:00 8 : : : : :
Fri 00:00 8 : : : : :
Sat 00:00 8 :


Routing Patterns
Route
Index PGN 8
----- ------
1 100
2
3
4
5
6
7

I am so confused here i need both floors to use the same table but different route pattern

should i create a separate table and copy the same config



Auto Route Selection (ARS) - Access Code 1: 0 Access Code 2:

Display ars analysis 0 location 1
Location: 1 Percent Full: 0

Dialed Total Route Call Node ANI
String Min Max Pattern Type Num Reqd
00 8 24 1 pubu n
01 10 10 1 pubu n
02 10 10 1 pubu n
03 10 10 1 pubu n
04 10 10 1 pubu n
05 10 10 1 pubu n
06 10 10 1 pubu n
07 10 10 1 pubu n
08 10 10 1 pubu n

 

[4merAvaya]

For stations with COR 100 you want to create a new Route Pattern with the trunk groups that you want to use. Within the Partition Route table there should be an entry under PGN 1 & PGN 8.

PARTITION ROUTING TABLE

Routing Patterns
Route
Index PGN 1 PGN 2 PGN 3 PGN 4 PGN 5 PGN 6 PGN 7 PGN 8
----- ------ ------ ------ ------ ------ ------ ------ ------
1 1 2 40 24 11
2 1 81 41 24 11

You also need to modify the ARS Analysis table to point to the Partition Route table by using 'pxx'.
list ars analysis Page 1

ARS DIGIT ANALYSIS REPORT

Location: all

Dialed Total Route Call Node
String Min Max Pattern Type Number

0 1 1 p1 op
0 8 8 p2 op
0 11 11 p2 op
00 2 2 p2 op



Below is the link to the World Class Routing feature.

Kevin

Link

 

[Arvindsunny]

Great thanks for the reply your just super

i will create

step 1
cor 100
time Time of Day Chart: 8

step 2
check timing display time-of-day 8

step 3

Routing Patterns
Route
Index PGN 8
----- ------
1 8


step 4

list ars analysis

my page is empty without any dialing string so over here i added the dial string as the same in

display ars ana 0 location 1 but just need to put p8


for example can i do some like this

cor 3 --> route pattern 1
cor 100 ---> rote pattern 10


change ars ana
Dialed Total Route Call Node ANI
String Min Max Pattern Type Num Reqd
0 4 24 1 pubu n
0 4 24 p8 op n


i think there is mistake in 3

please guide i am very close and interesting