Hi all
I have a NCUI4 card when I tried to configure I found that the loadware is in compatible with my openscape 4000 V7 system, so I tried to install loadware by use of file from my server by hints of following document:
OpenScape 4000 V7, Volume 4: IP Solutions, Service Documentation, Issue 2
10 How to reset an NCUI board
10.4 Process
but it doesn't copy file from the FTP server which is my laptop amd all firewall and antivirus rules are disabled.
but following error accured:
Error: Cannot open connection or invalid paramter!
Error loading file: errno = 0x4b0007.
Error: Cannot load image!
how can I transfer the file to NCUI board?
RS232 initialized for Output: 38400,8,n,1
loading FPGA: FPGA default code found
Load O.K.
testing Checksum Firmware: Test O.K.
testing Data-Bus DRAM: Test O.K.
testing Address-Bus DRAM: Test O.K.
testing Pattern 0x55555555: Test O.K.
testing Pattern 0xAAAAAAAA: Test O.K.
FPGA Registers access: Test O.K.
testing ICGX Registers: Test O.K.
testing PHY identifier value: Test O.K.
Board Selftest complete
SENTA Version c found
SENTA configured line = 0
SENTA configured !
**************************************************
* NCUI4 *
**************************************************
Copyright 2006 Siemens AG
Hardware ID : 0x0680
Serial Number : SK763093020156
Parts List Version : -14
Bootrom Version : NCUI4_FW_070924
Processor speed = 266 MHz
PLB speed = 133 MHz
OPB speed = 44 MHz
Ext Bus speed = 33 MHz
PCI Bus speed = 33 MHz (Async)
PCI Async Ext Clock being used.
Internal PCI arbiter enabled
FPGA Version : 8
Ethernet Address 1 : 00:1A:E8:1A:BF:4A
Ethernet Address 2 : 00:1A:E8:1A:BF:4B
CPU - Type : IBM PowerNP NPe405H Rev. A Rev. 0140
- Frequency : 266 MHz
Flash Memory : 32 MByte
DRAM Module : 256 MByte (SDRAM PC133 )
DSP On board :
DSP 0 present: YES - type: "6416"
DSP 1 present: YES - type: "6416"
HGA Module present: YES - type: "PDMX-X300"
Shelf ID : 0 = AP3700IP (SAPP Base Box)
System date: SAT JAN 01 00:00:00 2000
/tffs/ - disk check in progress ...
/tffs/ - Volume is OK
total # of clusters: 15,057
# of free clusters: 15,053
# of bad clusters: 0
total free space: 30,106 Kb
max contiguous free space: 30,828,544 bytes
# of files: 2
# of folders: 0
total bytes in files: 144
# of lost chains: 0
total bytes in lost chains: 0
*******************************************
/tffs - directory Entries:
Type: Size: Name: LW image from: act:
file 72 bootline.act
file 72 bootline.bck
Total TFFS size: 30836736 bytes / free: 30828544 bytes
Press any key to stop auto-boot...
0
auto-booting...
Try to load image file PZKNCI40.
Error: Could not open file.Try to load image file PZKNCI40.
Error: Could not open file.Try to load image file PZKNCI40.
Error: Could not open file.Try to load image file PZKNCI40.
Error: Could not open file.
Error: couldn't load any loadware image!
No CLI password has been set yet.
Please, use the 'b' command to set a password.
[NCUI2 Boot CLI]: p
boot device : emac
unit number : 0
processor number : 0
file name : PZKNCI40
inet on ethernet (e) : 192.168.1.80:ffffff00
host inet (h) : 192.168.1.85
flags (f) : 0x80
other (o) : emac
[NCUI2 Boot CLI]: P
Current TFFS directory: /tffs
[NCUI2 Boot CLI]: c
'.' = clear field; '-' = go to previous field; ^D = quit
boot device : emac0 emac
processor number : 0 0
host name : .
file name : PZKNCI40 PZKNCI40
inet on ethernet (e) : 192.168.1.80:ffffff00 192.168.1.80:ffffff00
inet on backplane (b): .
host inet (h) : 192.168.1.85 192.168.1.85
gateway inet (g) : .
user (u) : .
ftp password (pw) (blank = use rsh): .
flags (f) : 0x80 .
target name (tn) : .
startup script (s) : .
other (o) : emac emac
[NCUI2 Boot CLI]: c
'.' = clear field; '-' = go to previous field; ^D = quit
boot device : emac0 emac
processor number : 0 0
invalid number.
processor number : 0
host name :
file name : PZKNCI40
inet on ethernet (e) : 192.168.1.80:ffffff00
inet on backplane (b):
host inet (h) : 192.168.1.85
gateway inet (g) :
user (u) :
ftp password (pw) (blank = use rsh):
flags (f) : 0x0
target name (tn) :
startup script (s) :
other (o) : emac
[NCUI2 Boot CLI]:
[NCUI2 Boot CLI]: c
'.' = clear field; '-' = go to previous field; ^D = quit
boot device : emac0 emac
processor number : 0
host name :
file name : PZKNCI40
inet on ethernet (e) : 192.168.1.80:ffffff00
inet on backplane (b):
host inet (h) : 192.168.1.85
gateway inet (g) :
user (u) :
ftp password (pw) (blank = use rsh):
flags (f) : 0x0 0x80
target name (tn) :
startup script (s) :
other (o) : emac emac
[NCUI2 Boot CLI]: z
Copy content of /tffs/bootline.act into /tffs/bootline.bck.
Write /tffs/bootline.act ok!
[NCUI2 Boot CLI]: w
Changed to root directory!
*******************************************
/tffs - directory Entries:
Type: Size: Name: LW image from: act:
file 72 bootline.act
file 72 bootline.bck
Total TFFS size: 30836736 bytes / free: 30828544 bytes
Input a new suffix SW_IMAGE.x: 001
New image name: SW_IMAGE.001 ok (y/n)? y
boot device : emac
unit number : 0
processor number : 0
file name : PZKNCI40
inet on ethernet (e) : 192.168.1.80:ffffff00
host inet (h) : 192.168.1.85
flags (f) : 0x80
other (o) : emac
Attached TCP/IP interface to emac0.
Attaching network interface lo0... done.
Loading...
Delete ok!
Error: Cannot open connection or invalid paramter!
Error loading file: errno = 0x4b0007.
Error: Cannot load image!
[NCUI2 Boot CLI]:
I have a NCUI4 card when I tried to configure I found that the loadware is in compatible with my openscape 4000 V7 system, so I tried to install loadware by use of file from my server by hints of following document:
OpenScape 4000 V7, Volume 4: IP Solutions, Service Documentation, Issue 2
10 How to reset an NCUI board
10.4 Process
but it doesn't copy file from the FTP server which is my laptop amd all firewall and antivirus rules are disabled.
but following error accured:
Error: Cannot open connection or invalid paramter!
Error loading file: errno = 0x4b0007.
Error: Cannot load image!
how can I transfer the file to NCUI board?
RS232 initialized for Output: 38400,8,n,1
loading FPGA: FPGA default code found
Load O.K.
testing Checksum Firmware: Test O.K.
testing Data-Bus DRAM: Test O.K.
testing Address-Bus DRAM: Test O.K.
testing Pattern 0x55555555: Test O.K.
testing Pattern 0xAAAAAAAA: Test O.K.
FPGA Registers access: Test O.K.
testing ICGX Registers: Test O.K.
testing PHY identifier value: Test O.K.
Board Selftest complete
SENTA Version c found
SENTA configured line = 0
SENTA configured !
**************************************************
* NCUI4 *
**************************************************
Copyright 2006 Siemens AG
Hardware ID : 0x0680
Serial Number : SK763093020156
Parts List Version : -14
Bootrom Version : NCUI4_FW_070924
Processor speed = 266 MHz
PLB speed = 133 MHz
OPB speed = 44 MHz
Ext Bus speed = 33 MHz
PCI Bus speed = 33 MHz (Async)
PCI Async Ext Clock being used.
Internal PCI arbiter enabled
FPGA Version : 8
Ethernet Address 1 : 00:1A:E8:1A:BF:4A
Ethernet Address 2 : 00:1A:E8:1A:BF:4B
CPU - Type : IBM PowerNP NPe405H Rev. A Rev. 0140
- Frequency : 266 MHz
Flash Memory : 32 MByte
DRAM Module : 256 MByte (SDRAM PC133 )
DSP On board :
DSP 0 present: YES - type: "6416"
DSP 1 present: YES - type: "6416"
HGA Module present: YES - type: "PDMX-X300"
Shelf ID : 0 = AP3700IP (SAPP Base Box)
System date: SAT JAN 01 00:00:00 2000
/tffs/ - disk check in progress ...
/tffs/ - Volume is OK
total # of clusters: 15,057
# of free clusters: 15,053
# of bad clusters: 0
total free space: 30,106 Kb
max contiguous free space: 30,828,544 bytes
# of files: 2
# of folders: 0
total bytes in files: 144
# of lost chains: 0
total bytes in lost chains: 0
*******************************************
/tffs - directory Entries:
Type: Size: Name: LW image from: act:
file 72 bootline.act
file 72 bootline.bck
Total TFFS size: 30836736 bytes / free: 30828544 bytes
Press any key to stop auto-boot...
0
auto-booting...
Try to load image file PZKNCI40.
Error: Could not open file.Try to load image file PZKNCI40.
Error: Could not open file.Try to load image file PZKNCI40.
Error: Could not open file.Try to load image file PZKNCI40.
Error: Could not open file.
Error: couldn't load any loadware image!
No CLI password has been set yet.
Please, use the 'b' command to set a password.
[NCUI2 Boot CLI]: p
boot device : emac
unit number : 0
processor number : 0
file name : PZKNCI40
inet on ethernet (e) : 192.168.1.80:ffffff00
host inet (h) : 192.168.1.85
flags (f) : 0x80
other (o) : emac
[NCUI2 Boot CLI]: P
Current TFFS directory: /tffs
[NCUI2 Boot CLI]: c
'.' = clear field; '-' = go to previous field; ^D = quit
boot device : emac0 emac
processor number : 0 0
host name : .
file name : PZKNCI40 PZKNCI40
inet on ethernet (e) : 192.168.1.80:ffffff00 192.168.1.80:ffffff00
inet on backplane (b): .
host inet (h) : 192.168.1.85 192.168.1.85
gateway inet (g) : .
user (u) : .
ftp password (pw) (blank = use rsh): .
flags (f) : 0x80 .
target name (tn) : .
startup script (s) : .
other (o) : emac emac
[NCUI2 Boot CLI]: c
'.' = clear field; '-' = go to previous field; ^D = quit
boot device : emac0 emac
processor number : 0 0
invalid number.
processor number : 0
host name :
file name : PZKNCI40
inet on ethernet (e) : 192.168.1.80:ffffff00
inet on backplane (b):
host inet (h) : 192.168.1.85
gateway inet (g) :
user (u) :
ftp password (pw) (blank = use rsh):
flags (f) : 0x0
target name (tn) :
startup script (s) :
other (o) : emac
[NCUI2 Boot CLI]:
[NCUI2 Boot CLI]: c
'.' = clear field; '-' = go to previous field; ^D = quit
boot device : emac0 emac
processor number : 0
host name :
file name : PZKNCI40
inet on ethernet (e) : 192.168.1.80:ffffff00
inet on backplane (b):
host inet (h) : 192.168.1.85
gateway inet (g) :
user (u) :
ftp password (pw) (blank = use rsh):
flags (f) : 0x0 0x80
target name (tn) :
startup script (s) :
other (o) : emac emac
[NCUI2 Boot CLI]: z
Copy content of /tffs/bootline.act into /tffs/bootline.bck.
Write /tffs/bootline.act ok!
[NCUI2 Boot CLI]: w
Changed to root directory!
*******************************************
/tffs - directory Entries:
Type: Size: Name: LW image from: act:
file 72 bootline.act
file 72 bootline.bck
Total TFFS size: 30836736 bytes / free: 30828544 bytes
Input a new suffix SW_IMAGE.x: 001
New image name: SW_IMAGE.001 ok (y/n)? y
boot device : emac
unit number : 0
processor number : 0
file name : PZKNCI40
inet on ethernet (e) : 192.168.1.80:ffffff00
host inet (h) : 192.168.1.85
flags (f) : 0x80
other (o) : emac
Attached TCP/IP interface to emac0.
Attaching network interface lo0... done.
Loading...
Delete ok!
Error: Cannot open connection or invalid paramter!
Error loading file: errno = 0x4b0007.
Error: Cannot load image!
[NCUI2 Boot CLI]: