Name on Definity-IPOffice H323 Trunk

[CarlosPrex]

Need to configure a H323 Trunk between Definity R9.5 and IPOffice R9
Everything works fine, but on Definity side, phones don´t show name of the called party.

Hope someone can address me what´s needed to make it work.
Thanks in advance

Below Trunk Group and Signaling Group configuration:
-------------------------------------------------------------------------------------------
change trunk-group 29 Page 1 of 21
TRUNK GROUP

Group Number: 29 Group Type: isdn CDR Reports: y
Group Name: IPOFFICE COR: 4 TN: 1 TAC: 829
Direction: two-way Outgoing Display? n Carrier Medium: H.323
Dial Access? y Busy Threshold: 255 Night Service:
Queue Length: 0
Service Type: tie Auth Code? n
Member Assignment Method: manual




change trunk-group 29 Page 2 of 21
Group Type: isdn

TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): enbloc/enbloc


Digital Loss Group: 18
Incoming Calling Number - Delete: Insert: Format:

Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0
CONNECT Reliable When Call Leaves ISDN? n
XOIP Treatment: auto Delay Call Setup When Accessed Via IGAR? n



change trunk-group 29 Page 3 of 21
TRUNK FEATURES
ACA Assignment? n Measured: none
Internal Alert? n Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: y Send Calling Number: y
Used for DCS? n Hop Dgt? n Send EMU Visitor CPN? y
Suppress # Outpulsing? n Format: pub-unk
UUI IE Treatment: service-provider

Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: y
Hold/Unhold Notifications? y
Send UUI IE? y Modify Tandem Calling Number: no
Send UCID? n
Send Codeset 6/7 LAI IE? y


Show ANSWERED BY on Display? y

change trunk-group 29 Page 4 of 21
QSIG TRUNK GROUP OPTIONS




TSC Method for Auto Callback: drop-if-possible
Diversion by Reroute? y
Path Replacement? y
Path Replacement with Retention? n
Path Replacement Method: better-route
SBS? n

Character Set for QSIG Name: eurofont
QSIG Value-Added? n

SIP Reference Trunk Group:



change trunk-group 29 Page 5 of 21
TRUNK GROUP
Administered Members (min/max): 1/8
GROUP MEMBER ASSIGNMENTS Total Administered Members: 8

Port Name Night Sig Grp
1: T00055 29
2: T00056 29
3: T00057 29
4: T00058 29
5: T00059 29
6: T00060 29
7: T00061 29
8: T00062 29
-----------------------------------------------------------------------------------

change signaling-group 29 Page 1 of 1
SIGNALING GROUP

Group Number: 29 Group Type: h.323
SBS? n Remote Office? n Max number of NCA TSC: 0
Q-SIP? n Max number of CA TSC: 0
IP Video? n Trunk Group for NCA TSC:
Trunk Group for Channel Selection: 29 X-Mobility/Wireless Type: NONE
TSC Supplementary Service Protocol: a Network Call Transfer? n
T303 Timer(sec): 10
H.245 DTMF Signal Tone Duration(msec):
Near-end Node Name: CLAN Far-end Node Name: IPOFFICE
Near-end Listen Port: 1720 Far-end Listen Port: 1720
Far-end Network Region: 29
LRQ Required? n Calls Share IP Signaling Connection? n
RRQ Required? n
Bypass If IP Threshold Exceeded? n
H.235 Annex H Required? n
DTMF over IP: out-of-band Direct IP-IP Audio Connections? n
Link Loss Delay Timer(sec): 90 IP Audio Hairpinning? n
Enable Layer 3 Test? n Interworking Message: PROGress
DCP/Analog Bearer Capability: 3.1kHz

 

[Saiyan656]

the “Codeset to Send Display” field is set to “6” as shown on
page 2 above. If this field is left at the default value of 6, it will not display the
calling party name or connected party name sent in the Q.931 SETUP and CONNECT
messages, respectively. Change the “Codeset to Send Display” field to “0”

 

[CarlosPrex]

Thanks, I tried but It seems as if 0 or 6 makes no difference on here.