Petazetas754
Technical User
- Aug 13, 2004
- 17
My problem is: I can make calls to the pstn but i cant recieve calls from pstn (all local calls works perfect)
I tried putting Connection plar command in fxo vic but it doesnt works.
Have i the telephone numbers right?
Where must i put the number where i want calls in (for example telephone with number 005)
Heres all my configuration (Router 1760 and Callmanger Express 3.0)
6 ip phones ,i want all calls from pstn rings in one of them
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/telephony-service/dial-peer
Command was: show telephony-service dial-peer --------------------------------------------------------------------------------
dial-peer voice 20001 pots
destination-pattern 001
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/1
dial-peer voice 20002 pots
destination-pattern 002
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/2
dial-peer voice 20003 pots
destination-pattern 003
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/3
dial-peer voice 20004 pots
destination-pattern 005
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/4
dial-peer voice 20005 pots
destination-pattern 006
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/5
dial-peer voice 20006 pots
destination-pattern 004
huntstop
progress_ind setup enable 3
port 50/0/6
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
***
***
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/voice/port/2\/0
Command was: show voice port 2/0 --------------------------------------------------------------------------------
Foreign Exchange Office EU 2/0 Slot is 0, Sub-unit is 2, Port is 0
Type of VoicePort is FXO
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for ES
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Battery-Reversal is enabled
Number Of Rings is set to 1
Supervisory Disconnect is signal
Answer Supervision is inactive
Hook Status is On Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Out Type is dtmf
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Percent Break of Pulse is 65 percent
GuardOut timer is 2000 ms
Minimun ring duration timer is 125 ms--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*********
***********
Foreign Exchange Station 3/0 Slot is 0, Sub-unit is 3, Port is 0
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for US
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
No disconnect acknowledge
Ring Cadence is defined by CPTone Selection
Ring Cadence are [20 40] * 100 msec
Ringer Equivalence Number is set to 1--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
****
*****
Complete URL was: /exec/-/show/voice/port/summary
Command was: show voice port summary --------------------------------------------------------------------------------
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
========= == ============ ===== ==== ======== ======== ==
2/0 -- fxo-ls up dorm idle on-hook y
2/1 -- fxo-ls up dorm idle on-hook y
3/0 -- fxs-ls up dorm on-hook idle y
3/1 -- fxs-ls up dorm on-hook idle y
50/0/1 1 efxs up dorm on-hook idle y
50/0/1 2 efxs up dorm on-hook idle y
50/0/2 1 efxs up dorm on-hook idle y
50/0/2 2 efxs up dorm on-hook idle y
50/0/3 1 efxs up dorm on-hook idle y
50/0/3 2 efxs up dorm on-hook idle y
50/0/4 1 efxs up dorm on-hook idle y
50/0/4 2 efxs up dorm on-hook idle y
50/0/5 1 efxs up dorm on-hook idle y
50/0/5 2 efxs up dorm on-hook idle y
50/0/6 1 efxs up dorm on-hook idle y
50/0/6 2 efxs up dorm on-hook idle y
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*************
************
Complete URL was: /exec/-/show/voice/call/2\/0
Command was: show voice call 2/0 --------------------------------------------------------------------------------
2/0 - - - vpm level 1 state = FXOLS_ONHOOK
vpm level 0 state = S_UP
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
************
************
dial-peer hunt 0
AD PRE PASS
TAG TYPE MIN OPER PREFIX DEST-PATTERN FER THRU SESS-TARGET PORT
1 pots up up 9 0 2/0
2 pots up up 007 0 3/0
20001 pots up up 001 0 50/0/1
20002 pots up up 002 0 50/0/2
20003 pots up up 003 0 50/0/3
20004 pots up up 005 0 50/0/4
20005 pots up up 006 0 50/0/5
20006 pots up up 004 0 50/0/6--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
VoiceEncapPeer1
peer type = voice, information type = voice,
description = `',
tag = 1, destination-pattern = `9',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 1, Admin state is up, Operation state is up,
incoming called-number = `005', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits default
session-target = `', voice-port = `2/0',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = TRUE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 3717, Charged Units = 0,
Successful Calls = 2, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "10 ",
Last Disconnect Text is "normal call clearing (16)",
Last Setup Time = 13895.--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
VoiceEncapPeer2
peer type = voice, information type = voice,
description = `',
tag = 2, destination-pattern = `007',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 2, Admin state is up, Operation state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits default
session-target = `', voice-port = `3/0',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = TRUE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 0, Charged Units = 0,
Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "",
Last Disconnect Text is "",
Last Setup Time = 0.--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
VoiceEncapPeer20001
peer type = voice, information type = voice,
description = `',
tag = 20001, destination-pattern = `001',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 20001, Admin state is up, Operation state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = enabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits 0
session-target = `', voice-port = `50/0/1',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = FALSE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 0, Charged Units = 0,
Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "",
Last Disconnect Text is "",
Last Setup Time = 0.--------------------------------------------------------------------------------command completed.
VoiceEncapPeer20002
peer type = voice, information type = voice,
description = `',
tag = 20002, destination-pattern = `002',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 20002, Admin state is up, Operation state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = enabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits 0
session-target = `', voice-port = `50/0/2',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = FALSE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 0, Charged Units = 0,
Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "",
Last Disconnect Text is "",
Last Setup Time = 0.--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
VoiceEncapPeer20003
peer type = voice, information type = voice,
description = `',
tag = 20003, destination-pattern = `003',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 20003, Admin state is up, Operation state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = enabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits 0
session-target = `', voice-port = `50/0/3',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = FALSE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 0, Charged Units = 0,
Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "",
Last Disconnect Text is "",
Last Setup Time = 0.--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
VoiceEncapPeer20005
peer type = voice, information type = voice,
description = `',
tag = 20005, destination-pattern = `006',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 20005, Admin state is up, Operation state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = enabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits 0
session-target = `', voice-port = `50/0/5',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = FALSE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 3714, Charged Units = 0,
Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 4, Refused Calls = 0,
Last Disconnect Cause is "10 ",
Last Disconnect Text is "normal call clearing (16)",
Last Setup Time = 15437.--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
******************************************************************************************************
********************************************************************************
***********************************************************************
Command was: show dialplan dialpeer 1 number 942037732 timeout --------------------------------------------------------------------------------Macro Exp.: 942037732
VoiceEncapPeer1
peer type = voice, information type = voice,
description = `',
tag = 1, destination-pattern = `9',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 1, Admin state is up, Operation state is up,
incoming called-number = `005', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits default
session-target = `', voice-port = `2/0',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = TRUE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 3717, Charged Units = 0,
Successful Calls = 2, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "10 ",
Last Disconnect Text is "normal call clearing (16)",
Last Setup Time = 13895.
Matched: 942037732 Digits: 1
Target:
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*****************************************************************************************************
********************************************************************************
***
Matched port
VoiceEncapPeer1
peer type = voice, information type = voice,
description = `',
tag = 1, destination-pattern = `9',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 1, Admin state is up, Operation state is up,
incoming called-number = `005', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits default
session-target = `', voice-port = `2/0',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = TRUE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 3717, Charged Units = 0,
Successful Calls = 2, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "10 ",
Last Disconnect Text is "normal call clearing (16)",
Last Setup Time = 13895.--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
****************
******************
Complete URL was: /exec/-/show/ephone-dn/summary
Command was: show ephone-dn summary --------------------------------------------------------------------------------
PORT DN STATE MWI_STATE CODEC VAD VTSP STATE VPM STATE
======== ========== ============ ======== === ===================== =========
50/0/1 CH1 IDLE CH2 IDLE NONE - - - EFXS_ONHOOK
50/0/2 CH1 IDLE CH2 IDLE NONE - - - EFXS_ONHOOK
50/0/3 CH1 IDLE CH2 IDLE NONE - - - EFXS_ONHOOK
50/0/4 CH1 IDLE CH2 IDLE NONE - - - EFXS_ONHOOK
50/0/5 CH1 IDLE CH2 IDLE NONE - - - EFXS_ONHOOK
50/0/6 CH1 IDLE CH2 IDLE NONE - - - EFXS_ONHOOK
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
***********
***********
ephone-1 Mac:000D.EDAB.653A TCP socket:[3] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:128.100.110.51 15967 7905 keepalive 31 max_line 2 dual-line
button 1: dn 1 number 001 CH1 IDLE CH2 IDLE
ephone-2 Mac:000D.EDC3.6723 TCP socket:[1] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:128.100.110.56 15967 7905 keepalive 31 max_line 2 dual-line
button 1: dn 5 number 006 CH1 IDLE CH2 IDLE
ephone-3 Mac:000D.EDAB.6327 TCP socket:[5] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:128.100.110.53 15967 7905 keepalive 31 max_line 2 dual-line
button 1: dn 3 number 003 CH1 IDLE CH2 IDLE
ephone-4 Mac:000E.386E.DD9B TCP socket:[2] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:128.100.110.52 15967 7905 keepalive 31 max_line 2 dual-line
button 1: dn 2 number 002 CH1 IDLE CH2 IDLE
ephone-5 Mac:000D.EDAB.648C TCP socket:[4] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:128.100.110.55 15968 7905 keepalive 31 max_line 2 dual-line
button 1: dn 4 number 005 CH1 IDLE CH2 IDLE
ephone-6 Mac:000E.386D.D29B TCP socket:[6] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:128.100.110.54 15964 7905 keepalive 31 max_line 2 dual-line
button 1: dn 6 number 004 CH1 IDLE CH2 IDLE
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
************
*************
Complete URL was: /exec/-/show/gateway
Command was: show gateway --------------------------------------------------------------------------------
H.323 ITU-T Version: 4.0 H323 Stack Version: 0.1
This gateway is not registered to any gatekeeper
Alias list (CLI configured)
E164-ID 007
E164-ID 004
Alias list (last RCF) is empty
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*********
***********
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/hardware
Command was: show hardware --------------------------------------------------------------------------------Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV8Y-M), Version 12.2(15)ZJ3, EARLY DEPLOYMENT RELEASE SOFTWARE (fc2)
TAC Support: Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Fri 26-Sep-03 01:33 by eaarmas
Image text-base: 0x80008120, data-base: 0x813BCC18
ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-SV8Y-M), Version 12.2(15)ZJ3, EARLY DEPLOYMENT RELEASE SOFTWARE (fc2)
Cisco1700 uptime is 18 minutes
System returned to ROM by power-on
System restarted at 08:09:44 GMT Fri Sep 24 2004
System image file is "flash:c1700-sv8y-mz[1].122-15.ZJ3.bin"
cisco 1760 (MPC860P) processor (revision 0x500) with 114688K/16384K bytes of memory.
Processor board ID FOC07481SSD (1622952791), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
1 ISDN Basic Rate interface(s)
2 Voice FXO interface(s)
2 Voice FXS interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x3922
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
****************
******************
**** No Global ISDN Switchtype currently defined ****
ISDN BRI0/0 interface
dsl 0, interface ISDN Switchtype = none
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x00000000
Total Allocated ISDN CCBs = 0--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
**********
************ç
OutputCommand base-URL was: /exec/-
Complete URL was: /exec/-/show/running-config/full
Command was: show running-config full --------------------------------------------------------------------------------
Building configuration...
Current configuration : 2558 bytes
!
! No configuration change since last restart
!
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Cisco1700
!
logging queue-limit 100
enable secret 5 $1$oZoY$O.Bc9D2rmbOXALtZGAusz/
enable password telematica
!
clock timezone GMT 1
ip subnet-zero
!
!
!
ip dhcp pool dynamicserver
network 128.100.0.0 255.255.0.0
option 150 ip 128.100.110.40
default-router 128.100.110.40
!
!
!
!
!
!
voice class h323 1
!
!
!
!
!
no voice hpi capture buffer
no voice hpi capture destination
!
!
mta receive maximum-recipients 0
!
!
!
interface FastEthernet0/0
ip address 128.100.110.40 255.255.0.0
speed auto
half-duplex
!
interface BRI0/0
no ip address
shutdown
!
interface Serial1/0
no ip address
shutdown
!
interface Serial1/1
no ip address
shutdown
!
ip classless
ip http server
ip http path flash
!
!
!
!
snmp-server community public RO
snmp-server enable traps tty
call rsvp-sync
!
voice-port 2/0
cptone ES
!
voice-port 2/1
!
voice-port 3/0
!
voice-port 3/1
!
!
mgcp profile default
!
dial-peer cor custom
!
!
!
dial-peer voice 1 pots
incoming called-number 005
destination-pattern 9
port 2/0
!
dial-peer voice 2 pots
destination-pattern 007
port 3/0
!
!
telephony-service
load 7905 CP79050101SCCP030530B
max-ephones 24
max-dn 120
ip source-address 128.100.110.40 port 2000
create cnf-files version-stamp 7960 Sep 24 2004 08:09:53
max-conferences 6
web admin system name telematica password telematica
dn-webedit
time-webedit
!
!
ephone-dn 1 dual-line
number 001 no-reg both
name Telematica1
hold-alert 30 originator
!
!
ephone-dn 2 dual-line
number 002 no-reg both
name Telematica2
hold-alert 30 originator
!
!
ephone-dn 3 dual-line
number 003 no-reg both
name Telematica3
hold-alert 30 originator
!
!
ephone-dn 4 dual-line
number 005 no-reg both
name Telematica5
hold-alert 30 originator
!
!
ephone-dn 5 dual-line
number 006 no-reg both
name Telematica6
hold-alert 30 originator
!
!
ephone-dn 6 dual-line
number 004
name telematica4
!
!
ephone 1
mac-address 000D.EDAB.653A
button 1:1
!
!
!
ephone 2
mac-address 000D.EDC3.6723
button 1:5
!
!
!
ephone 3
mac-address 000D.EDAB.6327
button 1:3
!
!
!
ephone 4
mac-address 000E.386E.DD9B
button 1:2
!
!
!
ephone 5
mac-address 000D.EDAB.648C
button 1:4
!
!
!
ephone 6
mac-address 000E.386D.D29B
type 7905
button 1:6
!
!
!
line con 0
speed 115200
line aux 0
line vty 0 4
password telematica
login
!
no scheduler allocate
ntp server 128.250.36.2
end
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
********
********
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/voice/port/2\/0
Command was: show voice port 2/0 --------------------------------------------------------------------------------
Foreign Exchange Office EU 2/0 Slot is 0, Sub-unit is 2, Port is 0
Type of VoicePort is FXO
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for ES
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Battery-Reversal is enabled
Number Of Rings is set to 1
Supervisory Disconnect is signal
Answer Supervision is inactive
Hook Status is On Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Out Type is dtmf
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Percent Break of Pulse is 65 percent
GuardOut timer is 2000 ms
Minimun ring duration timer is 125 ms--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*********
***********
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/voice/call/summary
Command was: show voice call summary --------------------------------------------------------------------------------
PORT CODEC VAD VTSP STATE VPM STATE
============ ======== === ==================== ======================
2/0 - - - FXOLS_ONHOOK
2/1 - - - FXOLS_ONHOOK
3/0 - - - FXSLS_ONHOOK
3/1 - - - FXSLS_ONHOOK
50/0/1 .1 - - - EFXS_ONHOOK
50/0/1 .2 - - - EFXS_ONHOOK
50/0/2 .1 - - - EFXS_ONHOOK
50/0/2 .2 - - - EFXS_ONHOOK
50/0/3 .1 - - - EFXS_ONHOOK
50/0/3 .2 - - - EFXS_ONHOOK
50/0/4 .1 - - - EFXS_ONHOOK
50/0/4 .2 - - - EFXS_ONHOOK
50/0/5 .1 - - - EFXS_ONHOOK
50/0/5 .2 - - - EFXS_ONHOOK
50/0/6 .1 - - - EFXS_ONHOOK
50/0/6 .2 - - - EFXS_ONHOOK
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*******
*********
OutputCommand base-URL was: /exec/-
Complete URL was: /exec/-/show/voice/trace/2\/0/detail
Command was: show voice trace 2/0 detail --------------------------------------------------------------------------------
2/0 Stack 0:
State Transitions: timestamp (state, event) -> (state, event) ...
14.972 (S_OPEN_PEND, E_DSP_INTERFACE_INFO) ->
14.972 (S_DOWN, E_DSP_SIG_0100) ->
14.972 (S_DOWN, E_HTSP_IF_INSERVICE) ->
14.976 (S_OPEN_PEND, E_DSP_INTERFACE_INFO) ->
14.976 (S_DOWN, E_DSP_SIG_0100) ->
14.976 (S_DOWN, E_HTSP_IF_INSERVICE) ->
14.980 (S_OPEN_PEND, E_HTSP_GO_UP) ->
Event Counts (zeros not shown): (event, count)
(E_HTSP_IF_INSERVICE, 2)
E_HTSP_GO_UP, 1) E_DSP_INTERFACE_INFO, 2) E_DSP_SIG_0100, 2)
State Counts (zeros not shown): (state, count)
(S_OPEN_PEND, 3)S_DOWN, 6) :
Stack 1:
State Transitions: timestamp (state, event) -> (state, event) ...
138.955 (FXOLS_ONHOOK, E_HTSP_SETUP_REQ) ->
138.955 (FXOLS_WAIT_DIAL_TONE, E_HTSP_EVENT_TIMER) ->
138.955 (FXOLS_WAIT_DIAL_DONE, E_DSP_DIALING_DONE) ->
138.963 (FXOLS_WAIT_CUT_THRU, E_HTSP_VOICE_CUT_THROUGH) ->
154.132 (FXOLS_OFFHOOK, E_HTSP_RELEASE_REQ) ->
156.135 (FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER) ->
156.135 (FXOLS_ONHOOK, E_DSP_SIG_0100) ->
Event Counts (zeros not shown): (event, count)
(E_HTSP_SETUP_REQ, 1)E_HTSP_RELEASE_REQ, 1) E_HTSP_VOICE_CUT_THROUGH, 1) E_DSP_DIALING_DONE, 1)
(E_DSP_SIG_0100, 1)E_HTSP_EVENT_TIMER, 2) :
State Counts (zeros not shown): (state, count)
(FXOLS_ONHOOK, 2)FXOLS_OFFHOOK, 1) FXOLS_WAIT_DIAL_TONE, 1) FXOLS_WAIT_DIAL_DONE, 1)
(FXOLS_WAIT_CUT_THRU, 1)FXOLS_GUARD_OUT, 1) :
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*********
*********
CONFIG (Version=3.0)
=====================
Cisco CallManager Express
ip source-address 128.100.110.40 port 2000
load 7905 CP79050101SCCP030530B
max-ephones 24
max-dn 120
max-conferences 6
max-redirect 5
time-format 12
date-format mm-dd-yy
keepalive 30
timeout interdigit 10
timeout busy 10
timeout ringing 180
web admin system name telematica password telematica
web admin customer name Customer
edit DN through Web: enabled.
edit TIME through web: enabled.
Log (table parameters):
max-size: 150
retain-timer: 15
create cnf-files version-stamp 7960 Sep 24 2004 08:09:53
local directory service: enabled.
ephone-dn 1 dual-line
number 001 no-reg both
name Telematica1
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 2 dual-line
number 002 no-reg both
name Telematica2
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 3 dual-line
number 003 no-reg both
name Telematica3
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 4 dual-line
number 005 no-reg both
name Telematica5
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 5 dual-line
number 006 no-reg both
name Telematica6
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 6 dual-line
number 004
name telematica4
preference 0 secondary 9
huntstop
no huntstop channel
ephone 1
mac-address 000D.EDAB.653A
button 1:1
!
ephone 2
mac-address 000D.EDC3.6723
button 1:5
!
ephone 3
mac-address 000D.EDAB.6327
button 1:3
!
ephone 4
mac-address 000E.386E.DD9B
button 1:2
!
ephone 5
mac-address 000D.EDAB.648C
button 1:4
!
ephone 6
mac-address 000E.386D.D29B
type 7905
button 1:6
!
voice-port 50/0/1
station-id number 001
station-id name Telematica1
!
voice-port 50/0/2
station-id number 002
station-id name Telematica2
!
voice-port 50/0/3
station-id number 003
station-id name Telematica3
!
voice-port 50/0/4
station-id number 005
station-id name Telematica5
!
voice-port 50/0/5
station-id number 006
station-id name Telematica6
!
voice-port 50/0/6
station-id number 004
station-id name telematica4
!
dial-peer voice 20001 pots
destination-pattern 001
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/1
dial-peer voice 20002 pots
destination-pattern 002
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/2
dial-peer voice 20003 pots
destination-pattern 003
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/3
dial-peer voice 20004 pots
destination-pattern 005
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/4
dial-peer voice 20005 pots
destination-pattern 006
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/5
dial-peer voice 20006 pots
destination-pattern 004
huntstop
progress_ind setup enable 3
port 50/0/6
tftp-server system:/its/SEPDEFAULT.cnf
tftp-server system:/its/SEPDEFAULT.cnf alias SEPDefault.cnf
tftp-server system:/its/XMLDefault.cnf.xml alias XMLDefault.cnf.xml
tftp-server system:/its/ATADefault.cnf.xml
tftp-server system:/its/united_states/7960-tones.xml alias United_States/7960-tones.xml
tftp-server system:/its/united_states/7960-font.xml alias English_United_States/7960-font.xml
tftp-server system:/its/united_states/7960-dictionary.xml alias English_United_States/7960-dictionary.xml
tftp-server system:/its/united_states/7960-kate.xml alias English_United_States/7960-kate.xml
tftp-server system:/its/united_states/SCCP-dictionary.xml alias English_United_States/SCCP-dictionary.xml
tftp-server system:/its/XMLDefault7905.cnf.xml alias SEP000E386DD29B.cnf.xml
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
********
********
OutputCommand base-URL was: /exec/-
Complete URL was: /exec/-/show/telephony-service/ephone-dn
Command was: show telephony-service ephone-dn --------------------------------------------------------------------------------
ephone-dn 1 dual-line
number 001 no-reg both
name Telematica1
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 2 dual-line
number 002 no-reg both
name Telematica2
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 3 dual-line
number 003 no-reg both
name Telematica3
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 4 dual-line
number 005 no-reg both
name Telematica5
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 5 dual-line
number 006 no-reg both
name Telematica6
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 6 dual-line
number 004
name telematica4
preference 0 secondary 9
huntstop
no huntstop channel
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*********
************
voice-port 50/0/1
station-id number 001
station-id name Telematica1
!
voice-port 50/0/2
station-id number 002
station-id name Telematica2
!
voice-port 50/0/3
station-id number 003
station-id name Telematica3
!
voice-port 50/0/4
station-id number 005
station-id name Telematica5
!
voice-port 50/0/5
station-id number 006
station-id name Telematica6
!
voice-port 50/0/6
station-id number 004
station-id name telematica4
!
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
**********
************
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/telephony-service/dial-peer
Command was: show telephony-service dial-peer --------------------------------------------------------------------------------
dial-peer voice 20001 pots
destination-pattern 001
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/1
dial-peer voice 20002 pots
destination-pattern 002
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/2
dial-peer voice 20003 pots
destination-pattern 003
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/3
dial-peer voice 20004 pots
destination-pattern 005
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/4
dial-peer voice 20005 pots
destination-pattern 006
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/5
dial-peer voice 20006 pots
destination-pattern 004
huntstop
progress_ind setup enable 3
port 50/0/6
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
***
***
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/voice/port/2\/0
Command was: show voice port 2/0 --------------------------------------------------------------------------------
Foreign Exchange Office EU 2/0 Slot is 0, Sub-unit is 2, Port is 0
Type of VoicePort is FXO
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for ES
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Battery-Reversal is enabled
Number Of Rings is set to 1
Supervisory Disconnect is signal
Answer Supervision is inactive
Hook Status is On Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Out Type is dtmf
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Percent Break of Pulse is 65 percent
GuardOut timer is 2000 ms
Minimun ring duration timer is 125 ms--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*********
***********
Foreign Exchange Station 3/0 Slot is 0, Sub-unit is 3, Port is 0
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for US
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
No disconnect acknowledge
Ring Cadence is defined by CPTone Selection
Ring Cadence are [20 40] * 100 msec
Ringer Equivalence Number is set to 1--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
****
*****
Complete URL was: /exec/-/show/voice/port/summary
Command was: show voice port summary --------------------------------------------------------------------------------
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
========= == ============ ===== ==== ======== ======== ==
2/0 -- fxo-ls up dorm idle on-hook y
2/1 -- fxo-ls up dorm idle on-hook y
3/0 -- fxs-ls up dorm on-hook idle y
3/1 -- fxs-ls up dorm on-hook idle y
50/0/1 1 efxs up dorm on-hook idle y
50/0/1 2 efxs up dorm on-hook idle y
50/0/2 1 efxs up dorm on-hook idle y
50/0/2 2 efxs up dorm on-hook idle y
50/0/3 1 efxs up dorm on-hook idle y
50/0/3 2 efxs up dorm on-hook idle y
50/0/4 1 efxs up dorm on-hook idle y
50/0/4 2 efxs up dorm on-hook idle y
50/0/5 1 efxs up dorm on-hook idle y
50/0/5 2 efxs up dorm on-hook idle y
50/0/6 1 efxs up dorm on-hook idle y
50/0/6 2 efxs up dorm on-hook idle y
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*************
************
Complete URL was: /exec/-/show/voice/call/2\/0
Command was: show voice call 2/0 --------------------------------------------------------------------------------
2/0 - - - vpm level 1 state = FXOLS_ONHOOK
vpm level 0 state = S_UP
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
************
************
I tried putting Connection plar command in fxo vic but it doesnt works.
Have i the telephone numbers right?
Where must i put the number where i want calls in (for example telephone with number 005)
Heres all my configuration (Router 1760 and Callmanger Express 3.0)
6 ip phones ,i want all calls from pstn rings in one of them
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/telephony-service/dial-peer
Command was: show telephony-service dial-peer --------------------------------------------------------------------------------
dial-peer voice 20001 pots
destination-pattern 001
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/1
dial-peer voice 20002 pots
destination-pattern 002
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/2
dial-peer voice 20003 pots
destination-pattern 003
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/3
dial-peer voice 20004 pots
destination-pattern 005
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/4
dial-peer voice 20005 pots
destination-pattern 006
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/5
dial-peer voice 20006 pots
destination-pattern 004
huntstop
progress_ind setup enable 3
port 50/0/6
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
***
***
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/voice/port/2\/0
Command was: show voice port 2/0 --------------------------------------------------------------------------------
Foreign Exchange Office EU 2/0 Slot is 0, Sub-unit is 2, Port is 0
Type of VoicePort is FXO
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for ES
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Battery-Reversal is enabled
Number Of Rings is set to 1
Supervisory Disconnect is signal
Answer Supervision is inactive
Hook Status is On Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Out Type is dtmf
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Percent Break of Pulse is 65 percent
GuardOut timer is 2000 ms
Minimun ring duration timer is 125 ms--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*********
***********
Foreign Exchange Station 3/0 Slot is 0, Sub-unit is 3, Port is 0
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for US
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
No disconnect acknowledge
Ring Cadence is defined by CPTone Selection
Ring Cadence are [20 40] * 100 msec
Ringer Equivalence Number is set to 1--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
****
*****
Complete URL was: /exec/-/show/voice/port/summary
Command was: show voice port summary --------------------------------------------------------------------------------
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
========= == ============ ===== ==== ======== ======== ==
2/0 -- fxo-ls up dorm idle on-hook y
2/1 -- fxo-ls up dorm idle on-hook y
3/0 -- fxs-ls up dorm on-hook idle y
3/1 -- fxs-ls up dorm on-hook idle y
50/0/1 1 efxs up dorm on-hook idle y
50/0/1 2 efxs up dorm on-hook idle y
50/0/2 1 efxs up dorm on-hook idle y
50/0/2 2 efxs up dorm on-hook idle y
50/0/3 1 efxs up dorm on-hook idle y
50/0/3 2 efxs up dorm on-hook idle y
50/0/4 1 efxs up dorm on-hook idle y
50/0/4 2 efxs up dorm on-hook idle y
50/0/5 1 efxs up dorm on-hook idle y
50/0/5 2 efxs up dorm on-hook idle y
50/0/6 1 efxs up dorm on-hook idle y
50/0/6 2 efxs up dorm on-hook idle y
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*************
************
Complete URL was: /exec/-/show/voice/call/2\/0
Command was: show voice call 2/0 --------------------------------------------------------------------------------
2/0 - - - vpm level 1 state = FXOLS_ONHOOK
vpm level 0 state = S_UP
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
************
************
dial-peer hunt 0
AD PRE PASS
TAG TYPE MIN OPER PREFIX DEST-PATTERN FER THRU SESS-TARGET PORT
1 pots up up 9 0 2/0
2 pots up up 007 0 3/0
20001 pots up up 001 0 50/0/1
20002 pots up up 002 0 50/0/2
20003 pots up up 003 0 50/0/3
20004 pots up up 005 0 50/0/4
20005 pots up up 006 0 50/0/5
20006 pots up up 004 0 50/0/6--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
VoiceEncapPeer1
peer type = voice, information type = voice,
description = `',
tag = 1, destination-pattern = `9',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 1, Admin state is up, Operation state is up,
incoming called-number = `005', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits default
session-target = `', voice-port = `2/0',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = TRUE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 3717, Charged Units = 0,
Successful Calls = 2, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "10 ",
Last Disconnect Text is "normal call clearing (16)",
Last Setup Time = 13895.--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
VoiceEncapPeer2
peer type = voice, information type = voice,
description = `',
tag = 2, destination-pattern = `007',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 2, Admin state is up, Operation state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits default
session-target = `', voice-port = `3/0',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = TRUE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 0, Charged Units = 0,
Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "",
Last Disconnect Text is "",
Last Setup Time = 0.--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
VoiceEncapPeer20001
peer type = voice, information type = voice,
description = `',
tag = 20001, destination-pattern = `001',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 20001, Admin state is up, Operation state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = enabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits 0
session-target = `', voice-port = `50/0/1',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = FALSE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 0, Charged Units = 0,
Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "",
Last Disconnect Text is "",
Last Setup Time = 0.--------------------------------------------------------------------------------command completed.
VoiceEncapPeer20002
peer type = voice, information type = voice,
description = `',
tag = 20002, destination-pattern = `002',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 20002, Admin state is up, Operation state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = enabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits 0
session-target = `', voice-port = `50/0/2',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = FALSE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 0, Charged Units = 0,
Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "",
Last Disconnect Text is "",
Last Setup Time = 0.--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
VoiceEncapPeer20003
peer type = voice, information type = voice,
description = `',
tag = 20003, destination-pattern = `003',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 20003, Admin state is up, Operation state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = enabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits 0
session-target = `', voice-port = `50/0/3',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = FALSE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 0, Charged Units = 0,
Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "",
Last Disconnect Text is "",
Last Setup Time = 0.--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
VoiceEncapPeer20005
peer type = voice, information type = voice,
description = `',
tag = 20005, destination-pattern = `006',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 20005, Admin state is up, Operation state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = enabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits 0
session-target = `', voice-port = `50/0/5',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = FALSE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 3714, Charged Units = 0,
Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 4, Refused Calls = 0,
Last Disconnect Cause is "10 ",
Last Disconnect Text is "normal call clearing (16)",
Last Setup Time = 15437.--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
******************************************************************************************************
********************************************************************************
***********************************************************************
Command was: show dialplan dialpeer 1 number 942037732 timeout --------------------------------------------------------------------------------Macro Exp.: 942037732
VoiceEncapPeer1
peer type = voice, information type = voice,
description = `',
tag = 1, destination-pattern = `9',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 1, Admin state is up, Operation state is up,
incoming called-number = `005', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits default
session-target = `', voice-port = `2/0',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = TRUE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 3717, Charged Units = 0,
Successful Calls = 2, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "10 ",
Last Disconnect Text is "normal call clearing (16)",
Last Setup Time = 13895.
Matched: 942037732 Digits: 1
Target:
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*****************************************************************************************************
********************************************************************************
***
Matched port
VoiceEncapPeer1
peer type = voice, information type = voice,
description = `',
tag = 1, destination-pattern = `9',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 1, Admin state is up, Operation state is up,
incoming called-number = `005', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
type = pots, prefix = `',
forward-digits default
session-target = `', voice-port = `2/0',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = TRUE
fax rate = system, payload size = 20 bytes
Time elapsed since last clearing of voice call statistics never
Connect Time = 3717, Charged Units = 0,
Successful Calls = 2, Failed Calls = 0, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "10 ",
Last Disconnect Text is "normal call clearing (16)",
Last Setup Time = 13895.--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
****************
******************
Complete URL was: /exec/-/show/ephone-dn/summary
Command was: show ephone-dn summary --------------------------------------------------------------------------------
PORT DN STATE MWI_STATE CODEC VAD VTSP STATE VPM STATE
======== ========== ============ ======== === ===================== =========
50/0/1 CH1 IDLE CH2 IDLE NONE - - - EFXS_ONHOOK
50/0/2 CH1 IDLE CH2 IDLE NONE - - - EFXS_ONHOOK
50/0/3 CH1 IDLE CH2 IDLE NONE - - - EFXS_ONHOOK
50/0/4 CH1 IDLE CH2 IDLE NONE - - - EFXS_ONHOOK
50/0/5 CH1 IDLE CH2 IDLE NONE - - - EFXS_ONHOOK
50/0/6 CH1 IDLE CH2 IDLE NONE - - - EFXS_ONHOOK
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
***********
***********
ephone-1 Mac:000D.EDAB.653A TCP socket:[3] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:128.100.110.51 15967 7905 keepalive 31 max_line 2 dual-line
button 1: dn 1 number 001 CH1 IDLE CH2 IDLE
ephone-2 Mac:000D.EDC3.6723 TCP socket:[1] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:128.100.110.56 15967 7905 keepalive 31 max_line 2 dual-line
button 1: dn 5 number 006 CH1 IDLE CH2 IDLE
ephone-3 Mac:000D.EDAB.6327 TCP socket:[5] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:128.100.110.53 15967 7905 keepalive 31 max_line 2 dual-line
button 1: dn 3 number 003 CH1 IDLE CH2 IDLE
ephone-4 Mac:000E.386E.DD9B TCP socket:[2] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:128.100.110.52 15967 7905 keepalive 31 max_line 2 dual-line
button 1: dn 2 number 002 CH1 IDLE CH2 IDLE
ephone-5 Mac:000D.EDAB.648C TCP socket:[4] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:128.100.110.55 15968 7905 keepalive 31 max_line 2 dual-line
button 1: dn 4 number 005 CH1 IDLE CH2 IDLE
ephone-6 Mac:000E.386D.D29B TCP socket:[6] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:128.100.110.54 15964 7905 keepalive 31 max_line 2 dual-line
button 1: dn 6 number 004 CH1 IDLE CH2 IDLE
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
************
*************
Complete URL was: /exec/-/show/gateway
Command was: show gateway --------------------------------------------------------------------------------
H.323 ITU-T Version: 4.0 H323 Stack Version: 0.1
This gateway is not registered to any gatekeeper
Alias list (CLI configured)
E164-ID 007
E164-ID 004
Alias list (last RCF) is empty
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*********
***********
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/hardware
Command was: show hardware --------------------------------------------------------------------------------Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV8Y-M), Version 12.2(15)ZJ3, EARLY DEPLOYMENT RELEASE SOFTWARE (fc2)
TAC Support: Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Fri 26-Sep-03 01:33 by eaarmas
Image text-base: 0x80008120, data-base: 0x813BCC18
ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-SV8Y-M), Version 12.2(15)ZJ3, EARLY DEPLOYMENT RELEASE SOFTWARE (fc2)
Cisco1700 uptime is 18 minutes
System returned to ROM by power-on
System restarted at 08:09:44 GMT Fri Sep 24 2004
System image file is "flash:c1700-sv8y-mz[1].122-15.ZJ3.bin"
cisco 1760 (MPC860P) processor (revision 0x500) with 114688K/16384K bytes of memory.
Processor board ID FOC07481SSD (1622952791), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
1 ISDN Basic Rate interface(s)
2 Voice FXO interface(s)
2 Voice FXS interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x3922
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
****************
******************
**** No Global ISDN Switchtype currently defined ****
ISDN BRI0/0 interface
dsl 0, interface ISDN Switchtype = none
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x00000000
Total Allocated ISDN CCBs = 0--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
**********
************ç
OutputCommand base-URL was: /exec/-
Complete URL was: /exec/-/show/running-config/full
Command was: show running-config full --------------------------------------------------------------------------------
Building configuration...
Current configuration : 2558 bytes
!
! No configuration change since last restart
!
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Cisco1700
!
logging queue-limit 100
enable secret 5 $1$oZoY$O.Bc9D2rmbOXALtZGAusz/
enable password telematica
!
clock timezone GMT 1
ip subnet-zero
!
!
!
ip dhcp pool dynamicserver
network 128.100.0.0 255.255.0.0
option 150 ip 128.100.110.40
default-router 128.100.110.40
!
!
!
!
!
!
voice class h323 1
!
!
!
!
!
no voice hpi capture buffer
no voice hpi capture destination
!
!
mta receive maximum-recipients 0
!
!
!
interface FastEthernet0/0
ip address 128.100.110.40 255.255.0.0
speed auto
half-duplex
!
interface BRI0/0
no ip address
shutdown
!
interface Serial1/0
no ip address
shutdown
!
interface Serial1/1
no ip address
shutdown
!
ip classless
ip http server
ip http path flash
!
!
!
!
snmp-server community public RO
snmp-server enable traps tty
call rsvp-sync
!
voice-port 2/0
cptone ES
!
voice-port 2/1
!
voice-port 3/0
!
voice-port 3/1
!
!
mgcp profile default
!
dial-peer cor custom
!
!
!
dial-peer voice 1 pots
incoming called-number 005
destination-pattern 9
port 2/0
!
dial-peer voice 2 pots
destination-pattern 007
port 3/0
!
!
telephony-service
load 7905 CP79050101SCCP030530B
max-ephones 24
max-dn 120
ip source-address 128.100.110.40 port 2000
create cnf-files version-stamp 7960 Sep 24 2004 08:09:53
max-conferences 6
web admin system name telematica password telematica
dn-webedit
time-webedit
!
!
ephone-dn 1 dual-line
number 001 no-reg both
name Telematica1
hold-alert 30 originator
!
!
ephone-dn 2 dual-line
number 002 no-reg both
name Telematica2
hold-alert 30 originator
!
!
ephone-dn 3 dual-line
number 003 no-reg both
name Telematica3
hold-alert 30 originator
!
!
ephone-dn 4 dual-line
number 005 no-reg both
name Telematica5
hold-alert 30 originator
!
!
ephone-dn 5 dual-line
number 006 no-reg both
name Telematica6
hold-alert 30 originator
!
!
ephone-dn 6 dual-line
number 004
name telematica4
!
!
ephone 1
mac-address 000D.EDAB.653A
button 1:1
!
!
!
ephone 2
mac-address 000D.EDC3.6723
button 1:5
!
!
!
ephone 3
mac-address 000D.EDAB.6327
button 1:3
!
!
!
ephone 4
mac-address 000E.386E.DD9B
button 1:2
!
!
!
ephone 5
mac-address 000D.EDAB.648C
button 1:4
!
!
!
ephone 6
mac-address 000E.386D.D29B
type 7905
button 1:6
!
!
!
line con 0
speed 115200
line aux 0
line vty 0 4
password telematica
login
!
no scheduler allocate
ntp server 128.250.36.2
end
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
********
********
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/voice/port/2\/0
Command was: show voice port 2/0 --------------------------------------------------------------------------------
Foreign Exchange Office EU 2/0 Slot is 0, Sub-unit is 2, Port is 0
Type of VoicePort is FXO
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for ES
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Battery-Reversal is enabled
Number Of Rings is set to 1
Supervisory Disconnect is signal
Answer Supervision is inactive
Hook Status is On Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Out Type is dtmf
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Percent Break of Pulse is 65 percent
GuardOut timer is 2000 ms
Minimun ring duration timer is 125 ms--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*********
***********
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/voice/call/summary
Command was: show voice call summary --------------------------------------------------------------------------------
PORT CODEC VAD VTSP STATE VPM STATE
============ ======== === ==================== ======================
2/0 - - - FXOLS_ONHOOK
2/1 - - - FXOLS_ONHOOK
3/0 - - - FXSLS_ONHOOK
3/1 - - - FXSLS_ONHOOK
50/0/1 .1 - - - EFXS_ONHOOK
50/0/1 .2 - - - EFXS_ONHOOK
50/0/2 .1 - - - EFXS_ONHOOK
50/0/2 .2 - - - EFXS_ONHOOK
50/0/3 .1 - - - EFXS_ONHOOK
50/0/3 .2 - - - EFXS_ONHOOK
50/0/4 .1 - - - EFXS_ONHOOK
50/0/4 .2 - - - EFXS_ONHOOK
50/0/5 .1 - - - EFXS_ONHOOK
50/0/5 .2 - - - EFXS_ONHOOK
50/0/6 .1 - - - EFXS_ONHOOK
50/0/6 .2 - - - EFXS_ONHOOK
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*******
*********
OutputCommand base-URL was: /exec/-
Complete URL was: /exec/-/show/voice/trace/2\/0/detail
Command was: show voice trace 2/0 detail --------------------------------------------------------------------------------
2/0 Stack 0:
State Transitions: timestamp (state, event) -> (state, event) ...
14.972 (S_OPEN_PEND, E_DSP_INTERFACE_INFO) ->
14.972 (S_DOWN, E_DSP_SIG_0100) ->
14.972 (S_DOWN, E_HTSP_IF_INSERVICE) ->
14.976 (S_OPEN_PEND, E_DSP_INTERFACE_INFO) ->
14.976 (S_DOWN, E_DSP_SIG_0100) ->
14.976 (S_DOWN, E_HTSP_IF_INSERVICE) ->
14.980 (S_OPEN_PEND, E_HTSP_GO_UP) ->
Event Counts (zeros not shown): (event, count)
(E_HTSP_IF_INSERVICE, 2)
E_HTSP_GO_UP, 1) E_DSP_INTERFACE_INFO, 2) E_DSP_SIG_0100, 2)State Counts (zeros not shown): (state, count)
(S_OPEN_PEND, 3)
S_DOWN, 6) :Stack 1:
State Transitions: timestamp (state, event) -> (state, event) ...
138.955 (FXOLS_ONHOOK, E_HTSP_SETUP_REQ) ->
138.955 (FXOLS_WAIT_DIAL_TONE, E_HTSP_EVENT_TIMER) ->
138.955 (FXOLS_WAIT_DIAL_DONE, E_DSP_DIALING_DONE) ->
138.963 (FXOLS_WAIT_CUT_THRU, E_HTSP_VOICE_CUT_THROUGH) ->
154.132 (FXOLS_OFFHOOK, E_HTSP_RELEASE_REQ) ->
156.135 (FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER) ->
156.135 (FXOLS_ONHOOK, E_DSP_SIG_0100) ->
Event Counts (zeros not shown): (event, count)
(E_HTSP_SETUP_REQ, 1)
E_HTSP_RELEASE_REQ, 1) E_HTSP_VOICE_CUT_THROUGH, 1) E_DSP_DIALING_DONE, 1)(E_DSP_SIG_0100, 1)
E_HTSP_EVENT_TIMER, 2) :State Counts (zeros not shown): (state, count)
(FXOLS_ONHOOK, 2)
FXOLS_OFFHOOK, 1) FXOLS_WAIT_DIAL_TONE, 1) FXOLS_WAIT_DIAL_DONE, 1)(FXOLS_WAIT_CUT_THRU, 1)
FXOLS_GUARD_OUT, 1) :--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*********
*********
CONFIG (Version=3.0)
=====================
Cisco CallManager Express
ip source-address 128.100.110.40 port 2000
load 7905 CP79050101SCCP030530B
max-ephones 24
max-dn 120
max-conferences 6
max-redirect 5
time-format 12
date-format mm-dd-yy
keepalive 30
timeout interdigit 10
timeout busy 10
timeout ringing 180
web admin system name telematica password telematica
web admin customer name Customer
edit DN through Web: enabled.
edit TIME through web: enabled.
Log (table parameters):
max-size: 150
retain-timer: 15
create cnf-files version-stamp 7960 Sep 24 2004 08:09:53
local directory service: enabled.
ephone-dn 1 dual-line
number 001 no-reg both
name Telematica1
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 2 dual-line
number 002 no-reg both
name Telematica2
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 3 dual-line
number 003 no-reg both
name Telematica3
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 4 dual-line
number 005 no-reg both
name Telematica5
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 5 dual-line
number 006 no-reg both
name Telematica6
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 6 dual-line
number 004
name telematica4
preference 0 secondary 9
huntstop
no huntstop channel
ephone 1
mac-address 000D.EDAB.653A
button 1:1
!
ephone 2
mac-address 000D.EDC3.6723
button 1:5
!
ephone 3
mac-address 000D.EDAB.6327
button 1:3
!
ephone 4
mac-address 000E.386E.DD9B
button 1:2
!
ephone 5
mac-address 000D.EDAB.648C
button 1:4
!
ephone 6
mac-address 000E.386D.D29B
type 7905
button 1:6
!
voice-port 50/0/1
station-id number 001
station-id name Telematica1
!
voice-port 50/0/2
station-id number 002
station-id name Telematica2
!
voice-port 50/0/3
station-id number 003
station-id name Telematica3
!
voice-port 50/0/4
station-id number 005
station-id name Telematica5
!
voice-port 50/0/5
station-id number 006
station-id name Telematica6
!
voice-port 50/0/6
station-id number 004
station-id name telematica4
!
dial-peer voice 20001 pots
destination-pattern 001
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/1
dial-peer voice 20002 pots
destination-pattern 002
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/2
dial-peer voice 20003 pots
destination-pattern 003
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/3
dial-peer voice 20004 pots
destination-pattern 005
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/4
dial-peer voice 20005 pots
destination-pattern 006
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/5
dial-peer voice 20006 pots
destination-pattern 004
huntstop
progress_ind setup enable 3
port 50/0/6
tftp-server system:/its/SEPDEFAULT.cnf
tftp-server system:/its/SEPDEFAULT.cnf alias SEPDefault.cnf
tftp-server system:/its/XMLDefault.cnf.xml alias XMLDefault.cnf.xml
tftp-server system:/its/ATADefault.cnf.xml
tftp-server system:/its/united_states/7960-tones.xml alias United_States/7960-tones.xml
tftp-server system:/its/united_states/7960-font.xml alias English_United_States/7960-font.xml
tftp-server system:/its/united_states/7960-dictionary.xml alias English_United_States/7960-dictionary.xml
tftp-server system:/its/united_states/7960-kate.xml alias English_United_States/7960-kate.xml
tftp-server system:/its/united_states/SCCP-dictionary.xml alias English_United_States/SCCP-dictionary.xml
tftp-server system:/its/XMLDefault7905.cnf.xml alias SEP000E386DD29B.cnf.xml
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
********
********
OutputCommand base-URL was: /exec/-
Complete URL was: /exec/-/show/telephony-service/ephone-dn
Command was: show telephony-service ephone-dn --------------------------------------------------------------------------------
ephone-dn 1 dual-line
number 001 no-reg both
name Telematica1
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 2 dual-line
number 002 no-reg both
name Telematica2
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 3 dual-line
number 003 no-reg both
name Telematica3
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 4 dual-line
number 005 no-reg both
name Telematica5
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 5 dual-line
number 006 no-reg both
name Telematica6
preference 0 secondary 9
huntstop
no huntstop channel
hold-alert 30 originator
ephone-dn 6 dual-line
number 004
name telematica4
preference 0 secondary 9
huntstop
no huntstop channel
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*********
************
voice-port 50/0/1
station-id number 001
station-id name Telematica1
!
voice-port 50/0/2
station-id number 002
station-id name Telematica2
!
voice-port 50/0/3
station-id number 003
station-id name Telematica3
!
voice-port 50/0/4
station-id number 005
station-id name Telematica5
!
voice-port 50/0/5
station-id number 006
station-id name Telematica6
!
voice-port 50/0/6
station-id number 004
station-id name telematica4
!
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
**********
************
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/telephony-service/dial-peer
Command was: show telephony-service dial-peer --------------------------------------------------------------------------------
dial-peer voice 20001 pots
destination-pattern 001
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/1
dial-peer voice 20002 pots
destination-pattern 002
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/2
dial-peer voice 20003 pots
destination-pattern 003
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/3
dial-peer voice 20004 pots
destination-pattern 005
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/4
dial-peer voice 20005 pots
destination-pattern 006
no e164 registration
huntstop
progress_ind setup enable 3
port 50/0/5
dial-peer voice 20006 pots
destination-pattern 004
huntstop
progress_ind setup enable 3
port 50/0/6
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
***
***
Command base-URL was: /exec/-
Complete URL was: /exec/-/show/voice/port/2\/0
Command was: show voice port 2/0 --------------------------------------------------------------------------------
Foreign Exchange Office EU 2/0 Slot is 0, Sub-unit is 2, Port is 0
Type of VoicePort is FXO
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for ES
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Battery-Reversal is enabled
Number Of Rings is set to 1
Supervisory Disconnect is signal
Answer Supervision is inactive
Hook Status is On Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Out Type is dtmf
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Percent Break of Pulse is 65 percent
GuardOut timer is 2000 ms
Minimun ring duration timer is 125 ms--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*********
***********
Foreign Exchange Station 3/0 Slot is 0, Sub-unit is 3, Port is 0
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for US
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
No disconnect acknowledge
Ring Cadence is defined by CPTone Selection
Ring Cadence are [20 40] * 100 msec
Ringer Equivalence Number is set to 1--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
****
*****
Complete URL was: /exec/-/show/voice/port/summary
Command was: show voice port summary --------------------------------------------------------------------------------
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
========= == ============ ===== ==== ======== ======== ==
2/0 -- fxo-ls up dorm idle on-hook y
2/1 -- fxo-ls up dorm idle on-hook y
3/0 -- fxs-ls up dorm on-hook idle y
3/1 -- fxs-ls up dorm on-hook idle y
50/0/1 1 efxs up dorm on-hook idle y
50/0/1 2 efxs up dorm on-hook idle y
50/0/2 1 efxs up dorm on-hook idle y
50/0/2 2 efxs up dorm on-hook idle y
50/0/3 1 efxs up dorm on-hook idle y
50/0/3 2 efxs up dorm on-hook idle y
50/0/4 1 efxs up dorm on-hook idle y
50/0/4 2 efxs up dorm on-hook idle y
50/0/5 1 efxs up dorm on-hook idle y
50/0/5 2 efxs up dorm on-hook idle y
50/0/6 1 efxs up dorm on-hook idle y
50/0/6 2 efxs up dorm on-hook idle y
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
*************
************
Complete URL was: /exec/-/show/voice/call/2\/0
Command was: show voice call 2/0 --------------------------------------------------------------------------------
2/0 - - - vpm level 1 state = FXOLS_ONHOOK
vpm level 0 state = S_UP
--------------------------------------------------------------------------------command completed.
--------------------------------------------------------------------------------
************
************
