Hi All,
I am facing an issue with ISDN tie trunk to cisco router. When i press access code (0) no dailtone and after that any digit I press got congestion. Not so sure what could be the issue.Cisco says the call not coming to their router at all. Our testing as below.
Ext 2439 and 2401 at MX-TSW. Cisco doesn't have any extension to create as we will use it to connect to other system later.So recently Cisco just re-route back incoming call to MX-TSW.
Access code is 0. We dialed 0+2401 from 2439. When I press 0, i saw on susip the call seize the trunk but no dialtone. After 0 whatever digit I press and got congestion. Cisco guy says no call is coming to their router. For my system I dont have Qsig license but we tried to configure as qsig. And I changed to Tie line without Qsig also same issue. The attached are both MX-TSW and Cisco config. Please advise me if there anything wrong with our setting or the method of testing is wrong (not possible to work?)
Thanks!
<rodap:rou=all;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
75 SL60 H'00000310 H'15440000 H'06200000 NO
76 SL60 H'00000310 H'15400000 H'06700000 NO
77 SL60 H'00000310 H'15400000 H'06700000 NO
81 TL22 H'010F0001 H'42121121 NO
<nutrp;
NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP ROU TARDST PRE TRC NEWTYP CONT BCAP HLC
33568223 0 0 76 1012 8 0
33568222 0 5 76 1012 8 0
1 2 4 0 0
2 2 4 0 0
3 2 4 0 0
4 2 4 0 0
5 2 4 0 0
6 2 4 0 0
7 2 4 0 0
8 2 4 0 0
9 2 4 0 0
END
<scexp;
EXTERNAL SYNC RECEIVING LINES DATA
MASTER LIM STATUS [MASTER SCOPE]
FIRST CHOICE 1-0-30-0 SYNC RECEIVING
SECOND CHOICE 1-2-20-0 OK
THIRD CHOICE NOT PRESENT
END
<roddp:dest=all;
EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
0 75 050500000000025010500101000 0 2 0
<exccp:cat=1&&10;
EXTENSION CATEGORY CODE
CAT TRAF SERV CDIV ROC
1 00010115 0200110000 010151111 000001
2 00020215 0200110000 010151111 000001
3 00030315 0200110000 011151111 000001
4 00000000 0000000000 000000000 000001
5 00000000 0000000000 000000000 000001
6 00000000 0000000000 000000000 000001
7 00000000 0000000000 000000000 000001
8 00000000 0000000000 000000000 000001
9 00000000 0000000000 000000000 000001
10 00000000 0000000000 000000000 000001
<nadap;
NUMBER ANALYSIS DATA
TYPE OF SERIES NUMBER SERIES
EXTENSION NUMBER SERIES 1000 - 1040
1200 - 1299
2000 - 2050
2210 - 2299
2400 - 2450
2460 - 2499
3300 - 3310
3500 - 3510
4000 - 4010
4100 - 4110
4200 - 4250
4300 - 4310
4600 - 4620
5454 - 5455
6800 - 6810
6900 - 6910
7400 - 7410
7600 - 7610
8000 - 8010
8100 - 8130
9300 - 9350
9900 - 9910
EXTERNAL DESTINATION CODE 0
77
TYPE OF SERVICE CODE SERVICE CODE
EXTERNAL NUMBER LENGTH DATA
EXTERNAL NUMBER NUMBER LENGTH
000 3 - 20
0011 4 - 20
0012 4 - 20
0013 4 - 20
0018 4 - 20
0019 4 - 20
005 3 - 20
02 2 - 20
03 2 - 20
06 2 - 20
08 2 - 20
09 2 - 20
1 4 - 4
2 2 - 20
3 2 - 20
PROCEED TO SEND SIGNAL DATA
EXTERNAL NUMBER POS. TYPE
CALL DISCRIMINATION DATA
EXTERNAL/INTERNAL NUMBER CAT
0 3 2 1 0
1 3 2 1 0
2 3 2 1 0
3 3 2 1 0
4 3 2 1 0
6 3 2 1 0
7 3 2 1 0
8 3 2 1 0
9 3 2 1 0
END
FORMAT ERROR
<rocap:rou=all;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
75 0110000000000010 5 3110000000 0 30 128 00151515 211110000030 111110
76 0110000000000010 5 3110000001 0 30 128 00151515 111100000031 111110
77 0110000000000010 5 3110000001 0 30 128 00151515 111100000030 111110
81 0010000000000010 4 0010000000 0 30 128 00151515 411100000000 001100
CISCO CONFIGURATION
RTR01#sh run
Building configuration...
Current configuration : 4470 bytes
!
! Last configuration change at 13:20:18 UTC Sun Feb 9 2014 by bbqlim
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname RTR01
!
boot-start-marker
boot-end-marker
!
!
card type e1 0 0
logging buffered 51200 warnings
enable password daelim
!
no aaa new-model
network-clock-participate wic 0
!
ip cef
!
!
!
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool ccp-pool
import all
network 10.10.10.0 255.255.255.248
default-router 10.10.10.1
lease 0 2
!
!
!
ip domain name bbqlim.com
no ipv6 cef
multilink bundle-name authenticated
!
!
!
!
isdn switch-type primary-qsig
!
!
crypto pki trustpoint TP-self-signed-3700012095
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3700012095
revocation-check none
rsakeypair TP-self-signed-3700012095
!
!
crypto pki certificate chain TP-self-signed-3700012095
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33373030 30313230 3935301E 170D3133 30323032 32323537
35365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 37303030
31323039 3530819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100C2B1 A2A2FF04 51EA0A6C 65CCCFF4 9C47667D AB660C73 DE6DBF98 0B08ED92
8F5F50AE 35957ECC 6FE2482A 42BE39E5 C9FA3531 AADFBDEE B5002C0F 032749BF
FA80ED6F 241009E1 35AAAF8D D0BADC44 4FEC8800 D979DE85 6B44A0E5 69298DFF
35512177 EC19CDFF BD5B79BD 34750380 6EDD063E D21DE1F8 E0ABB5CC FD60E9D6
72D90203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 14AB6227 37503F88 11EED5F0 FEF93129 F48E9B68 13301D06
03551D0E 04160414 AB622737 503F8811 EED5F0FE F93129F4 8E9B6813 300D0609
2A864886 F70D0101 05050003 8181002C 40AA88F2 94C6DEE8 3EC6BBC5 C54B14A8
17ABBC3D BFE9DC55 A28EBCE6 EF2CECBF 9F583458 337BA2B6 344B7024 9B88931A
6F71828B F7A9DAB0 5FA2DFE9 42C4D7F5 D9B5772F FE49BAAB F5BDB578 5778A8FC
970717C4 B019DD3A B3B3196B 29A2A194 DB85E2E7 B54F6299 DBB6C8BB 44770BDF
2BE7923E 60704E3F EF2BFD06 1A8F4B
quit
voice-card 0
dspfarm
!
!
!
!
!
!
!
!
license udi pid CISCO2911/K9 sn FGL170513D4
license boot module c2900 technology-package uck9
hw-module pvdm 0/1
!
!
!
username bbqlim password 0 bbqlim
!
redundancy
!
!
controller E1 0/0/0
clock source line bits
pri-group timeslots 1-31
!
controller E1 0/0/1
clock source line bits
pri-group timeslots 1-31
!
csdb tcp synwait-time 30
csdb tcp idle-time 3600
csdb tcp finwait-time 5
csdb tcp reassembly max-memory 1024
csdb tcp reassembly max-queue-length 16
csdb udp idle-time 30
csdb icmp idle-time 10
csdb session max-session 65535
!
!
!
!
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
description Management
ip address 192.168.1.1 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/1
ip address 192.168.2.2 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/2
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn timer T310 120000
isdn protocol-emulate network
isdn incoming-voice modem
no cdp enable
!
interface Serial0/0/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn timer T310 120000
isdn protocol-emulate network
isdn incoming-voice modem
no cdp enable
!
ip forward-protocol nd
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
ip route 0.0.0.0 0.0.0.0 192.168.2.1
!
!
!
!
control-plane
!
!
voice-port 0/0/0:15
!
voice-port 0/0/1:15
!
!
!
!
!
!
mgcp profile default
!
!
dial-peer voice 2401 pots
destination-pattern 2401
port 0/0/0:15
forward-digits 4
!
dial-peer voice 2439 pots
destination-pattern 2439
port 0/0/0:15
forward-digits 4
!
!
!
!
gatekeeper
shutdown
!
!
!
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
privilege level 15
login local
transport input ssh
line vty 5 15
privilege level 15
login local
transport input ssh
!
scheduler allocate 20000 1000
!
end
I am facing an issue with ISDN tie trunk to cisco router. When i press access code (0) no dailtone and after that any digit I press got congestion. Not so sure what could be the issue.Cisco says the call not coming to their router at all. Our testing as below.
Ext 2439 and 2401 at MX-TSW. Cisco doesn't have any extension to create as we will use it to connect to other system later.So recently Cisco just re-route back incoming call to MX-TSW.
Access code is 0. We dialed 0+2401 from 2439. When I press 0, i saw on susip the call seize the trunk but no dialtone. After 0 whatever digit I press and got congestion. Cisco guy says no call is coming to their router. For my system I dont have Qsig license but we tried to configure as qsig. And I changed to Tie line without Qsig also same issue. The attached are both MX-TSW and Cisco config. Please advise me if there anything wrong with our setting or the method of testing is wrong (not possible to work?)
Thanks!
<rodap:rou=all;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
75 SL60 H'00000310 H'15440000 H'06200000 NO
76 SL60 H'00000310 H'15400000 H'06700000 NO
77 SL60 H'00000310 H'15400000 H'06700000 NO
81 TL22 H'010F0001 H'42121121 NO
<nutrp;
NUMBER CONVERSION DATA
ENTRY CNVTYP NUMTYP ROU TARDST PRE TRC NEWTYP CONT BCAP HLC
33568223 0 0 76 1012 8 0
33568222 0 5 76 1012 8 0
1 2 4 0 0
2 2 4 0 0
3 2 4 0 0
4 2 4 0 0
5 2 4 0 0
6 2 4 0 0
7 2 4 0 0
8 2 4 0 0
9 2 4 0 0
END
<scexp;
EXTERNAL SYNC RECEIVING LINES DATA
MASTER LIM STATUS [MASTER SCOPE]
FIRST CHOICE 1-0-30-0 SYNC RECEIVING
SECOND CHOICE 1-2-20-0 OK
THIRD CHOICE NOT PRESENT
END
<roddp:dest=all;
EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
0 75 050500000000025010500101000 0 2 0
<exccp:cat=1&&10;
EXTENSION CATEGORY CODE
CAT TRAF SERV CDIV ROC
1 00010115 0200110000 010151111 000001
2 00020215 0200110000 010151111 000001
3 00030315 0200110000 011151111 000001
4 00000000 0000000000 000000000 000001
5 00000000 0000000000 000000000 000001
6 00000000 0000000000 000000000 000001
7 00000000 0000000000 000000000 000001
8 00000000 0000000000 000000000 000001
9 00000000 0000000000 000000000 000001
10 00000000 0000000000 000000000 000001
<nadap;
NUMBER ANALYSIS DATA
TYPE OF SERIES NUMBER SERIES
EXTENSION NUMBER SERIES 1000 - 1040
1200 - 1299
2000 - 2050
2210 - 2299
2400 - 2450
2460 - 2499
3300 - 3310
3500 - 3510
4000 - 4010
4100 - 4110
4200 - 4250
4300 - 4310
4600 - 4620
5454 - 5455
6800 - 6810
6900 - 6910
7400 - 7410
7600 - 7610
8000 - 8010
8100 - 8130
9300 - 9350
9900 - 9910
EXTERNAL DESTINATION CODE 0
77
TYPE OF SERVICE CODE SERVICE CODE
EXTERNAL NUMBER LENGTH DATA
EXTERNAL NUMBER NUMBER LENGTH
000 3 - 20
0011 4 - 20
0012 4 - 20
0013 4 - 20
0018 4 - 20
0019 4 - 20
005 3 - 20
02 2 - 20
03 2 - 20
06 2 - 20
08 2 - 20
09 2 - 20
1 4 - 4
2 2 - 20
3 2 - 20
PROCEED TO SEND SIGNAL DATA
EXTERNAL NUMBER POS. TYPE
CALL DISCRIMINATION DATA
EXTERNAL/INTERNAL NUMBER CAT
0 3 2 1 0
1 3 2 1 0
2 3 2 1 0
3 3 2 1 0
4 3 2 1 0
6 3 2 1 0
7 3 2 1 0
8 3 2 1 0
9 3 2 1 0
END
FORMAT ERROR
<rocap:rou=all;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
75 0110000000000010 5 3110000000 0 30 128 00151515 211110000030 111110
76 0110000000000010 5 3110000001 0 30 128 00151515 111100000031 111110
77 0110000000000010 5 3110000001 0 30 128 00151515 111100000030 111110
81 0010000000000010 4 0010000000 0 30 128 00151515 411100000000 001100
CISCO CONFIGURATION
RTR01#sh run
Building configuration...
Current configuration : 4470 bytes
!
! Last configuration change at 13:20:18 UTC Sun Feb 9 2014 by bbqlim
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname RTR01
!
boot-start-marker
boot-end-marker
!
!
card type e1 0 0
logging buffered 51200 warnings
enable password daelim
!
no aaa new-model
network-clock-participate wic 0
!
ip cef
!
!
!
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool ccp-pool
import all
network 10.10.10.0 255.255.255.248
default-router 10.10.10.1
lease 0 2
!
!
!
ip domain name bbqlim.com
no ipv6 cef
multilink bundle-name authenticated
!
!
!
!
isdn switch-type primary-qsig
!
!
crypto pki trustpoint TP-self-signed-3700012095
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3700012095
revocation-check none
rsakeypair TP-self-signed-3700012095
!
!
crypto pki certificate chain TP-self-signed-3700012095
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33373030 30313230 3935301E 170D3133 30323032 32323537
35365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 37303030
31323039 3530819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100C2B1 A2A2FF04 51EA0A6C 65CCCFF4 9C47667D AB660C73 DE6DBF98 0B08ED92
8F5F50AE 35957ECC 6FE2482A 42BE39E5 C9FA3531 AADFBDEE B5002C0F 032749BF
FA80ED6F 241009E1 35AAAF8D D0BADC44 4FEC8800 D979DE85 6B44A0E5 69298DFF
35512177 EC19CDFF BD5B79BD 34750380 6EDD063E D21DE1F8 E0ABB5CC FD60E9D6
72D90203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 14AB6227 37503F88 11EED5F0 FEF93129 F48E9B68 13301D06
03551D0E 04160414 AB622737 503F8811 EED5F0FE F93129F4 8E9B6813 300D0609
2A864886 F70D0101 05050003 8181002C 40AA88F2 94C6DEE8 3EC6BBC5 C54B14A8
17ABBC3D BFE9DC55 A28EBCE6 EF2CECBF 9F583458 337BA2B6 344B7024 9B88931A
6F71828B F7A9DAB0 5FA2DFE9 42C4D7F5 D9B5772F FE49BAAB F5BDB578 5778A8FC
970717C4 B019DD3A B3B3196B 29A2A194 DB85E2E7 B54F6299 DBB6C8BB 44770BDF
2BE7923E 60704E3F EF2BFD06 1A8F4B
quit
voice-card 0
dspfarm
!
!
!
!
!
!
!
!
license udi pid CISCO2911/K9 sn FGL170513D4
license boot module c2900 technology-package uck9
hw-module pvdm 0/1
!
!
!
username bbqlim password 0 bbqlim
!
redundancy
!
!
controller E1 0/0/0
clock source line bits
pri-group timeslots 1-31
!
controller E1 0/0/1
clock source line bits
pri-group timeslots 1-31
!
csdb tcp synwait-time 30
csdb tcp idle-time 3600
csdb tcp finwait-time 5
csdb tcp reassembly max-memory 1024
csdb tcp reassembly max-queue-length 16
csdb udp idle-time 30
csdb icmp idle-time 10
csdb session max-session 65535
!
!
!
!
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
description Management
ip address 192.168.1.1 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/1
ip address 192.168.2.2 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/2
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn timer T310 120000
isdn protocol-emulate network
isdn incoming-voice modem
no cdp enable
!
interface Serial0/0/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn timer T310 120000
isdn protocol-emulate network
isdn incoming-voice modem
no cdp enable
!
ip forward-protocol nd
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
ip route 0.0.0.0 0.0.0.0 192.168.2.1
!
!
!
!
control-plane
!
!
voice-port 0/0/0:15
!
voice-port 0/0/1:15
!
!
!
!
!
!
mgcp profile default
!
!
dial-peer voice 2401 pots
destination-pattern 2401
port 0/0/0:15
forward-digits 4
!
dial-peer voice 2439 pots
destination-pattern 2439
port 0/0/0:15
forward-digits 4
!
!
!
!
gatekeeper
shutdown
!
!
!
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
privilege level 15
login local
transport input ssh
line vty 5 15
privilege level 15
login local
transport input ssh
!
scheduler allocate 20000 1000
!
end
