Miran II cannot record message

[lexer]

Hi

I've got a 11c rls 4.0 and a Miran II card Version 2.0.15f (Rls 1), I'm trying to record an announcement to assign it to a Miran channel for an ACD group, I can enter to Miran using a phone set (TUI interface), Then I got to option 5 and when I dial 5 for recording, I receive the message from Miran "recording stops". Miran has enough space for recording, System information shows:

- System Information - [Admin]

Hardware Configuration

CPU : 486DX4-100
Level 2 Cache : 128 KBytes
System Memory : 16 MBytes
Disk A: (External ATA) : Not Installed
Disk B: (Internal ATA) : Not Installed
Disk C: (Internal PCI) : 4 MBytes (3217408 Bytes Free)

Software Configuration

Application : NTAG37AB Version 2.0.15f (Rls 1)
Codec Driver : Version 1.38i (0)
8051XA Firmware : VPS Firmware Rls 7.0
DSP Info : NG0225c1,02/05/98 (A-Law)
DSP Status : OK
Time & Date Sync : Download disabled

Can I load a .WAV file message to a PCMCIA disk A, copy the file message to Disk C and assign to Miran Channel?
Thanks In advance!!

 

[lexer]

Hi, I could record a message using Input channel 0 on Miran Card (analog 0), External music source and the Announcement Command: " RECORD a0 c:message 15".

Any ideas? why I cannot record messages using TUI interface? I set the extension that I'm using for recording "CLS UNR" I still receive message from Miran "Stop Recording" when I dial 5 for start recording

 

[mikepbx1]

Lexer, MIRAN can't play a WAV, but you can convert one. MIRAN requires mono, 8Khz, RAW, with A-law (.ALW) or μ-law (.ULW) companding depending on the Miran.

http://pbxbook.com/meridian/install/miran_aud.html

http://pbxbook.com

 

[Firebird Scrambler]

There were problems accessing the Miran TUI interface. I think it's best to use an analogue phone.




Firebird Scrambler
Nortel Meridian 1 / Succession and BCM / Norstar Programmer in the UK
Advance knowledge on BCM support

http://www.linkedin.com/in/davidbromley

 

[Firebird Scrambler]

I think this was the file that I had.


Firebird Scrambler
Nortel Meridian 1 / Succession and BCM / Norstar Programmer in the UK
Advance knowledge on BCM support

http://www.linkedin.com/in/davidbromley

 

[lexer]

Thanks for your answers, I'm using an analog extension but I doesn't work

 

[Firebird Scrambler]

Make sure it's set for tone or MF dialing and don't press the keys quickly!. Do it slowly so that the Miran can understand the tones.


Firebird Scrambler
Nortel Meridian 1 / Succession and BCM / Norstar Programmer in the UK
Advance knowledge on BCM support

http://www.linkedin.com/in/davidbromley

 

[lexer]

Tbanks.
Please, Does Anybody know the Miran Pinout for ethernet connection (on 50 pin amphenol connector)? the Miran manual on pages 254-258 shows Pinout, but I don't know which are for ethernet connection?

 

[Firebird Scrambler]

Please refer to the attached guide, but the answer is

The ports used here is 23 & 24. The individual colour codes are..

Nortel multi cable Standard Ethernet RJ45 Cable

Port 23a Violet / Green Pin 3 White / Green
Port 23 b Green / Violet Pin 6 Green / White
Port 24 a Violet / Brown Pin 1 White / Orange
Port 24b Brown / Violet Pin 2 Orange / White

If you have a spare “ITG” adapter, then just use the “T” LAN port.



Firebird Scrambler
Nortel Meridian 1 / Succession and BCM / Norstar Programmer in the UK
Advance knowledge on BCM support

http://www.linkedin.com/in/davidbromley

 

[lexer]

Thanks!!!