Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

MICB: Not logging in

Status
Not open for further replies.

gewt

Technical User
Aug 8, 2017
32
US
Hi all,

I've got an old MICB I've been trying to set up and I just absolutely cannot get any of the ports to log in...starting with just one as a test.

0006:SW DSPS 275 ln06860 ch00 11-17 15:33:26:516 LOG IN FAIL
is the message repeatedly logged in telnet

Here's the ACD:
TYPE ACD
CUST 0
ACDN 3400
MWC NO
DSAC NO
MAXP 32
SDNB NO
BSCW NO
ISAP NO
AACQ NO
RGAI NO
ACAA NO
FRRT
SRRT
NRRT
FROA NO
NCFW
FNCF NO
FORC NO
RTQT 0
SPCP YES
OBTN NO
RAO NO
CWTH 1
NCWL NO
BYTH 0
OVTH 2047
TOFT NONE
HPQ NO
OCN NO
OVDN
IFDN
OVBU LNK LNK LNK LNK
EMRT
MURT
RTPC NO
STIO
TSFT 20
HOML YES
RDNA NO
ACNT
NRAC NO
DAL NO
RPRT YES
RAGT 4
DURT 30
RSND 4
FCTH 20
CRQS 100
IVR NO

DES MICB0
TN 008 0 00 00
TYPE 2616
CDEN 8D
CUST 0
AOM 0
FDN
TGAR 1
LDN NO
NCOS 0
SGRP 0
RNPG 0
SCI 0
SSU
XLST
CLS CTD FBD WTA LPR MTD FND HTD ADD HFD
MWD LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD SLKD CCSD SWD LND CNDD
CFTD SFD MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDD CDMD LLCN MCTD CLBD AUTU
GPUD DPUD DNDD CFXD ARHD CNTD CLTD ASCD
CPFA CPTA ABDD CFHD FICD NAID BUZZ AHD
DDGA NAMA
DRDD EXR0
USRD ULAD RTDD RBDD RBHD PGND FLXA FTTC DNDY DNO3 MCBN
CPND_LANG ENG
HUNT
PLEV 02
SPID NONE
AST
IAPG 0
AACS NO
ITNA NO
DGRP
PRI 01
MLWU_LANG 0
DNDR 0
DTMK
KEY 00 ACD 3400 0 7500
AGN
01 SCR 5001 0 MARP
02 NRD
03 MSB
04 TRN
05
06
07
08
09
10
11
12
13
14
15

Any ideas?
 
Manual states HOML NO in the ACD config this stops the logout when headset/Handset is removed/hung up so this might be the issue

Also mentions KEY 9 CHG but just used with CDR
 
That has not changed anything, even after a reset of the card. :(

Something is spamming ERR5098 in console so I think something weird is going on with my bus...removing the CallPilot and MICB does not result in this error going away...

Does anyone know what pins are the voltage rails? I'd like to check what my power supply is outputting.

 
Option 11C running 24.x...forget the exact subversion.
 
ERR5098 is usually issues with the links to remote cabinets, but as you have the MICB in the main cabinet it should not be affected.
 
I have no remote cabinets...wonder what the hell is going on.
 
Ive got one of these somewhere in a switch working, I'll post the config early next week. you did know there's a web browser page for these as well don't you? have you logged in to that?

Remember if it doesn't work hit it harder

Scott UK
 
I have, yes.

Mine is a much older MICB so the webui isn't the greatest, CLI was mainly used for the error logs.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top