MGC DSP/Link error

[nortelcs100e5]

Hi all i am installing a CS1000e system, i have both DSP daughter board installed on MGC and i created
DB32-->4-0-0-0 upto 31 channels
DB96--->4-0-11-0 upto 96 channel,
All Ip`s are assigned i am getting following error

IPMG[4 0]
31/12/2006 03:35:51 LOG0006 SYS: VGW5000 Card initialized, all alarms cleared. (
202)
31/12/2006 03:35:51 LOG0001 SYS: VGW1036 Call server communication link: 10.10.1
0.2 down (20)
31/12/2006 03:35:54 LOG0006 SYS: VGW5036 Call server communication link: 10.10.1
0.2 up (20)
31/12/2006 03:35:54 LOG0001 VGW: VGW1124 MGC 4 0 DSP DB-96 detected in DB posit
ion 2 (70)
31/12/2006 03:35:54 LOG0003 VGW: Wrong configuration for DSPDB type of 32 port D
SPDB
31/12/2006 03:35:54 LOG0003 VGW: VGW2119 VGW VoIP parameter configuration failur
e : Incorrect/Missing DSP DB configuration, Boot-up aborted for DSP DB: 1 (51)
31/12/2006 03:35:54 LOG0003 VGW: VGW task will be stopped - Missing configuratio
n for DSP DB
31/12/2006 03:35:54 LOG0006 VGW: vgw shutdown
31/12/2006 03:35:54 LOG0006 VGW: vgwTimerInit: setPollingPeriod data is NOT read
y yet, force setPollingPeriod to default 30
31/12/2006 03:35:54 LOG0006 VGW: VGW5014 Ethernet carrier: eth0, OK (9)
31/12/2006 03:35:54 LOG0006 VGW: server <MGC> offline announce
31/12/2006 03:35:54 LOG0006 VGW: vgw task stopped
31/12/2006 03:35:54 LOG0003 PBX: itgMsgSend blocked, qid 132, noMsgs 0
31/12/2006 03:35:54 LOG0003 PBX: itgMsgSend blocked, qid 132, noMsgs 0
31/12/2006 03:35:54 LOG0003 PBX: itgMsgSend blocked, qid 132, noMsgs 0

below is the status of MGC software version
BOOTCODE: MGCBAD27
CSP: MGCCAD31
MSP: MGCMAA06
FPGA: MGCFAA12
APPLICATION: MGCAAA04

any help in this???
regards

 

[Triton101]

Check that DBTYPE is selected correctly for installed DSP daughterboard in Element Manager.

 

[MikeRizz]

Looks like you have a 96db in position 2, it can only go in position one on the card. One can be either a 32db or a 96, but position two can only be a db32.

 

[nortelcs100e5]

Hi, After installing current loadware and swapping DSP it is working ok now accept i dont have any tone on digital set(no 500 license) if i call from IP set to digital i get ring on digital set and i also able to talk but when i lift handset of DLC i dont get tone neither i can dial. i created Conf/TDS on loop 200 and 201 respectively and DTR on 4 0 14.
ANy help?

 

[Eddie79it]

Did you enable the CONF/TDS Loop using ENLM Command?
Maybe that you don't enable that.

 

[lama123]

Each DSP Board should have its own TLAN IP address configured in element manager.These addresses should be different from MGC TLAN IP address.Otherwise, the voice path
won't open especially when dealing with conversion from IP
to TDM and vice-versa.