Message Waiting Light Between Sites 1

[bfuller83]

So I have just setup a reclaimed option 11 at a new site. Because of this site I have been able to remove a old out of service pri on my 61 and repurpose it and establish communications to my new option 11 everything is working great but I can't get the dang message light to work. On the 61 whenever I leave a message for the dn on the 11 I see a:

PRI254 DCH: 27 DATA: 0 4

I have copied the dch configs for both sides as well as the rdb below. Thanks

61 Dch:

>ld 22
PT2000

REQ prt
TYPE adan dch 27

ADAN DCH 27
CTYP MSDL
DNUM 10
PORT 0
DES DOWNTOWNT1
USR PRI
DCHL 27
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
NASA NO
IFC SL1
SIDE USR
CNEG 1
RLS ID **
RCAP ND2 MWI
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7

REQ

61 RDB:

REQ: prt
TYPE: rdb
CUST 0
ROUT 27

TYPE RDB
CUST 00
ROUT 27
DES T1 TO DOWNTOWN
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS INT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO NO
CHTY BCH
CTYP UKWN
INAC YES
ISAR NO
DAPC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 3927
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO ESN5
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5


PAGE 002

TFD 0
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST NO
TTA YES
ABAN YES
CDRB NO
QREC NO
OAL YES
AIA NO
OAN YES
OPD NO
CDRX NO
NATL YES
VRAT NO
MUS NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

REQ:

11 Dch:

>ld 22
PT2000

REQ prt
TYPE adan dch 9

ADAN DCH 9
CTYP TMDI
CARD 09
PORT 1
DES t1tomaincampus
USR PRI
DCHL 9
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
NASA NO
IFC SL1
SIDE NET
SEMT 1
CNEG 1
RLS ID **
RCAP ND2 MWI
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7

REQ

11 rdb:


TYPE RDB
CUST 00
DMOD
ROUT 11
DES T1 TO RMTC
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS INT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO NO
CHTY BCH
CTYP UKWN
INAC YES
ISAR NO
DAPC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 3911
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS


PAGE 003

INST
ANTK
SIGO ESN5
ICIS YES
TIMR ICF 384
OGF 384
EOD 4096
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST NO
TTA YES
ABAN YES
CDRB NO
QREC NO
OAL YES
AIA NO
OAN NO
OPD NO
CDRX NO
NATL YES
VRAT NO
MUS NO
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO


REQ:


Thanks Again!

Bradley A. Fuller
Manager, Network Infrastructure
Kellogg Community College

 

[Jeffnortel]

We always Use "25" for the RLS ID on the dchannel. Also we use standard signal arrangement. RDB "SIGO = STD".

 

[bc1111]

Try turning on dch messaging and see if you are sending nms.

 

[KCFLHRC]

SIGO should be ESN5 as you have it. Try putting in the actual RLS of the PBX in the d-channel instead of leaving it blank.

 

[KCFLHRC]

PRI0254 Database Error: The DCH is interfacing with a software issue not supported by
the application. Output data: DCH: x DATA: y z . Where:
x = D-channelnumber y = Release ID
z = Service identifier
Action: Verify that the release ID in the configuration record is the same as the
software release running on the far end switch.
If available, turn on the Alarm Filtering Package (#243) or Upgrade all the ISDN
MCDN switches to the same software Release.
Severity: Critical. Critical to Monitor: Yes. SNMP trap: Yes

 

[bfuller83]

Where do I get the RLS info? Is is just looking to be 4 based on the iss prt below:

Option 11:
CALL SERVER/MAIN CAB
VERSION 2121
RELEASE 4
ISSUE 50 W +
IDLE_SET_DISPLAY NORTEL

Option 61:
VERSION 2521
RELEASE 4
ISSUE 00 T +
IDLE_SET_DISPLAY NORTEL

Bradley A. Fuller
Manager, Network Infrastructure
Kellogg Community College

 

[KCFLHRC]

If memory serves me correctly release 4 would actually be RLS 27 on your d-channel. But I believe 25 would work just fine.

 

[bfuller83]

It looks like that may have done it. I won't know for sure until I drive downtown tonight but I am not getting the PRI254 error and I see the last message on both switches is:

DCH 27 IMSG FACILITY REF 00000000 CH 0 TOD 16:49:40
FEAT :NMS

Thanks So much for all the pointers!!

Bradley A. Fuller
Manager, Network Infrastructure
Kellogg Community College

 

[KCFLHRC]

Yep, sounds like you got it fixed. Good deal.

 

[bfuller83]

Good to go! Thanks a bunch!

Bradley A. Fuller
Manager, Network Infrastructure
Kellogg Community College

 

[KCFLHRC]

Awesome!