Magix PRI dial plan routing 1

[jahms]

I have a system with a PRI that originally no calls would route out over the PRI. All calls would go out the 4 copper lines in the system. All of the programming in the ARS was correct for the calls to use the PRI first. I tried numerous things but ended up defaulting and starting over. I have everything up and running and all calls go out like they should over the PRI. My only issue is the dial plan routing seems not to be working. I have tried changing a few things and nothing has worked. I am now stuck on what to do next. Any help would be greatly appreciated. below is how it is so far.
thanks

PRI INFORMATION



Slot 4 Switch: DMS-100

System: By extension Base number:

BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
1 4 CallbyCall By Dial Plan

Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1

Line PhoneNumber NumberToSend
805 6034227600
806 6034227600
807 6034227600
808 6034227600
809 6034227600
810 6034227600
811 6034227600
812 6034227600
813 6034227600
814 6034227600
815 6034227600
816 6034227600
817 6034227600
818 6034227600
819 6034227600
820 6034227600
821 6034227600
822 6034227600
823 6034227600
824 6034227600
825 6034227600
826 6034227600
827 6034227600
Entry Number: 0 1 2 3
Pattern to Match: 101**** 10*** !`

Special Service Table

Entry Number: 0 1 2 3 4 5 6 7
Pattern to Match: 011 010 01 00 0 1
Operator: none none none none none none none none
Type of Number: I I I N N N N N
Digits to Delete: 3 0 0 0 0 0 0 0

Call-By-Call Service Table

Entry Number: 0 1 2 3 4
Pattern 0: 0
Pattern 1: 1
PRI INFORMATION


Pattern 2: 2
Pattern 3: 3
Pattern 4: 4
Pattern 5: 5
Pattern 6: 6
Pattern 7: 7
Pattern 8: 8
Pattern 9: 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ: No Service
DeleteDigits: 0 0 0 0 0

Entry Number: 5 6 7 8 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ:
DeleteDigits: 0 0 0 0 0

Dial Plan Routing Table

Entry Number: 0 1 2 3
NtwkServ: Any service
Expected Digits: 4 0 0 0
Pattern to Match: 0 0 0 0
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 4 5 6 7
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match: 0 0 0 0
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 8 9 10 11
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match: 0
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 12 13 14 15
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

 

[Telecomboy]

Do you have 4-digit extensions? and if so, do the extensions match the DID range?

 

[jahms]

Yes they are 4 digit extensions and they match the DNIS.
This was working before I defaulted the system.
Thanks

 

[Telecomboy]

The pattern to match should be blank not "0".

 

[jahms]

UNder the CBC service? I will make that change and let you know.
Thanks again. Helps to have other eyes looking at times.

 

[Telecomboy]

Under Dial Plan Routing. Your entry number 0 has:
ntwrk service = any
Expected digits = 4
Pattern to match= 0 (this should be blank)
Digits to delete= 0
Digits to add = blank

 

[jahms]

That was it. I must have gone in there and changed it during the late hours of programming. Can't thank you enough Telecomboy. You made my day.
Thanks again,
JDSlay