M3903 not allowing privacy on lines

[djk205]

I have 6 M3903's which are built as a squared system. However when user is on a call, other stations can barge into that phone call. There are no analog devices with that tn, Firmware on the stations is 080, thats whats on PBX, PBX release 25.40 with following Peps:

IN-SERVICE PATCHES : 28
PAT# PRS PATCH REF # NAME DATE FILENAME
00 DEPLIST ISS8:1OF7 CORE 04/10/04 p16000a8.cp3
01 DEPLIST ISS8:2OF7 CORE 04/10/04 p16000b8.cp3
02 deplist iss8:3of7 CORE 04/10/04 p16000c8.cp3
03 Deplist ISS8:4OF7 CORE 04/10/04 p16000d8.cp3
04 DEPLIST ISS8:5OF7 CORE 04/10/04 p16000e8.cp3
05 DEPLIST ISS8:6OF7 CORE 04/10/04 p16000f8.cp3
06 deplist iss8:7of7 CORE 04/10/04 p16000g8.cp3
07 DEPLIST ISS8:1OF2 SCCS 04/10/04 p16001a8.cp3
08 DEPLIST ISS8:2OF2 SCCS 04/10/04 p16001b8.cp3
09 DEPLIST ISS8:1OF1 CALLPILOT 04/10/04 p16002a8.cp3
10 Deplist ISS8:1OF2 TERMINALS 04/10/04 p16003a8.cp3
11 DEPLIST ISS8:2OF2 TERMINALS 04/10/04 p16003b8.cp3
12 Deplist ISS8:1OF2 IP 04/10/04 p16004a8.cp3
13 DEPLIST ISS8:2OF2 IP 04/10/04 p16004b8.cp3
14 DEPLIST ISS8:1OF3 INT'L NET 04/10/04 p16005a8.cp3
15 Deplist ISS8:2OF3 INT'L NET 04/10/04 p16005b8.cp3
16 DEPLIST ISS8:3Of3 INTL 04/10/04 p16005c8.cp3
17 Deplist ISS8:1OF2 EURO NET 04/10/04 p16006a8.cp3
18 DEPLIST ISS8:2OF2 EURO 04/10/04 p16006b8.cp3
19 DEPLIST ISS8:1OF2 SP_FE/ 04/10/04 p16007a8.cp3
20 DEPLIST ISS8:2OF2 SPECIALFEATURES 04/10/04 p16007b8.cp3
21 Deplist ISS8:1OF2 CALL PILOT/SCCS 04/10/04 p16008a8.cp3
22 Q005738 ISS1:1OF1 CALL PILOT 15/10/04 p18025_1.cp4
23 Q007936 ISS1:1OF1 CORE 16/02/05 P17715_1.CP3
24 MP13632 ISS1:1OF1 CORE 16/02/05 P15702_1.CP3
25 Q006692 ISS1:1OF2 MCDN 16/02/05 P17406A1.CP3
26 Q006692 ISS1:2OF2 MCDN 16/02/05 P17406B1.CP3
27 Q009558 ISS1:1OF1 p1

Any help is greatly appreciated.
Thanks!

 

[worldwidedialtone]

In CDB for FTR DATA is secrecy allowed? NOt sure that is the answer or will help

MIKE

 

[djk205]

Yes, it does have sya in opt for ftr_data, but thanks for the reply

 

[worldwidedialtone]

You said no analog sets share the TN but I figure you mean DN. If the DN is shared with a digital and an analog set, then I am not sure there is much you can do.

MIKE

 

[Johnthephoneguy]

Post the DNB when you print it for that DN

 

[djk205]

DN 5940
CPND
NAME OutPatDialysis
XPLN 14
DISPLAY_FMT FIRST,LAST
TYPE SL1
TN 028 0 08 07 KEY 00 DES IA 26 OCT 2006
(3903)
TN 028 0 08 06 KEY 00 MARP DES IA 26 OCT 2006
(3903)
TN 028 0 08 08 KEY 01 DES OUTDIA 4 OCT 2006
(3903)
TN 028 0 08 09 KEY 01 DES OUTDIA 4 OCT 2006
(3903)
TN 028 0 08 10 KEY 01 DES OUTDIA 4 OCT 2006
(3903)
TN 028 0 08 11 KEY 01 DES OUTDIA 26 OCT 2006
(3903)


NACT
REQ: prt
TYPE: tnb
TN 28 0 8 6
DATE
PAGE
DES

DES IA
TN 028 0 08 06
TYPE 3903
CDEN 8D
CTYP XDLC
CUST 0
FDN
TGAR 1
LDN NO
NCOS 4
SGRP 0
RNPG 0
SCI 0
SSU
LNRS 16
XLST
CLS CTD FBD WTA LPR MTD FND HTD TDD HFD GRLD CRPD STSD
MWA RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD SLKD CCSD SWD LNA CNDA
CFTD SFD DDV CNID CDCA MSID DAPA BFED RCBD
ICDD CDMD MCTD CLBD AUTU
GPUD DPUD DNDA CFXD ARHD CLTD ASCD
CPFA CPTA ABDD CFHD FICD NAID BUZZ AGRD MOAD AHD
DDGA NAMA
USRD ULAD RTDD RBDD RBHD PGND FLXD FTTC MCBN
CPND_LANG ENG
RCO 0
HUNT
PLEV 02
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLNG ENG
DNDR 0
KEY 00 SCR 5940 0 MARP
CPND
NAME OutPatDialysis
XPLN 14
DISPLAY_FMT FIRST,LAST
01 SCR 6940 0 MARP
CPND
NAME OutPatDialysis
XPLN 14
DISPLAY_FMT FIRST,LAST
02 SCR 6941 0 MARP
CPND
NAME OutPatDialysis
XPLN 14
DISPLAY_FMT FIRST,LAST
03 ADL 4
04
05
06
07
08
09
10
11
12
13
14
15
16
17 TRN
18 AO6
19 CFW 4 5600
20 RGA
21 PRK
22 RNP
23
24 PRS
25 CHG
26 CPN
27 CLT
28 RLT
29
30
31
DATE 26 OCT 2006


NACT
Thanks!

 

[acewarlock]

In the CLS POD should stop it, but try CLS POA and see if that does it.

Check all TN's

 

[Nortellian]

check the other phones that are able to barge in for cls poa. change to pod if they are poa.

 

[djk205]

I think I got it fixed, I reflashed firmware to phones, I was told that there was an analog device connected before so I outted all devices & rebuilt them. Retested lines ok.
Thanks all for your help.