Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations biv343 on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

M2250 Console on CS1000 CPPM Rel 7.6

Status
Not open for further replies.

Archiball

Technical User
Feb 14, 2008
2
CA
I am having trouble installing a an M2250 console on a 7.6 CS1000 system. The console has all 5 tns wired to it. Primary, secondary and power all on the same DLC and the 5 tns are in order. It has been programmed in loads 12, and 15. When I plug the console in she lights all LCD indicators like she is going through her self test and then stays that way. All LCDs lit and locked up. I have tried two additional consoles and cables same thing. I disabled the card and reseated it, no change. Any ideas out there?
 
1st tn to w/bl pair of 2250
2nd tn to w/or pair
3rd tn to w/sl pair

4th tn tip and 5th tn tip to rd/or pair
4th tn ring and 5th tn ring to rd/grn pair
 
Yes, that's how she is wired. Five consecutive tns. I am going back on Monday and move it to a new DLC card. See what that changes.
 
How far is the console from the phone system as short cable runs don't always require the power TN's.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website =
 
well it's not 5 consecutive tns---------the tip of the 4 and 5th to the rd/or pair and the 4th and 5th ring to the rd/grn pr.
 
M2250 Console Installation

Installation

All consoles should be installed as per NTP 553-3001-215 Telephone and Attendant Console Installation Guide (Installation and Maintenance Guide Book 2)
or Meridian Option 11 Standard Installation Guide NTP 553-3011-210.

Please ensure that in addition to the primary and secondary tns, two additional
power tns are fitted. These should be configured as power tns in Overlay 12,
type PWR. They should be cabled to the +AUX and -AUX leads.
When using PC console interface units (PCCIU) only one power TN is required and this is cabled to pair 5 (Slate/white,White/slate) on the TJF

NT have identified that failure to do this is contributing to the large number of consoles that are returned with no fault found.

#############################################

CIU power pins

The CIU only has 1 power. 2 TN + 1 PWR

If you connect the second power the CIU will not come in service

Ascom state that these are the pins below.
The CIU takes it's power from the +AUX and -AUX. It is different to that of the 2250 which uses the 3rd TN.


25 pair cable
from console
to MDF DB 25 on CIU

26 (w-bl) 14
1 (bl-w) 2
27 (w-or) 15
2 (or-w) 3
32 (r-or) 19
7 (or-r) 7
33 (r-g) 22
8 (g-r) 10

See the NTP on atttendant console for the + and - AUX connections as the tip and ring are tied together.

Apparently this extra power will stop general problems on the Smile software and other glitches like going in and out of night mode.




Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website =
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top