I'm new in Sun, i just recieved a sun v100 server, i already connected the server to a workstation (using the hyperterminal tool) and it seemmed to be fine... however when the LOM> prompt appears and i try to introduce various commands but it does nothing.
LOMlite starting up.
CPU type: H8/3437S, mode 3
Ram-test: 2048 bytes OK
Initialising i2c bus: OK
Searching for EEPROMs: 50(cfg)
I2c eeprom @50: OK
i2c bus speed code 01... OK
Probing for lm80s: none
Probing for lm75s: 48
Initialising lm75 @48: OK
System functions: PSUs fans breakers rails gpio temps host CLI ebus clock
LOMlite console
lom>
LOM event: +0h0m0s LOM booted
lom>poweron
(it does nothing...)
also when i turn the server on with the on/standby switch it also seems to be starting fine, but again when the ok prompt is displayed i try to execute commands and it does again nothing.
Firmware CORE Sun Microsystems, Inc.
@(#) core 1.0.18 2002/05/23 18:22
Software Power ON
Verifying NVRAM...Done
Bootmode is 0
MCR0 = 57b2ce06
MCR1 = 80008000
MCR2 = cff0ffff
MCR3 = b00003ff
Ecache Size = 512 KB
Clearing E$ Tags Done
Clearing I/D TLBs Done
Probing memory
Done
MEMBASE=0xc0000000
MEMSIZE=0x20000000
Clearing memory...Done
Turning ON MMUs Done
Copy ROM to RAM (154720 bytes) Done
Orig PC=0x1fff0007edc New PC=0xf0f07f34
Processor Speed=648MHz
Looking for Dropin FVM ... found
Decompressing Client Done
Transferring control to Client...
Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
Probing upa at 1f,0 pci
Probing upa at 0,0 SUNW,UltraSPARC-IIe (512 Kb)
Loading Support Packages: kbd-translator
Loading onboard drivers:
Probing /pci@1f,0 Device 7 isa dma rtc power SUNW,lomh serial serial
flashprom
Probing /pci@1f,0 Device 3 pmu i2c temperature dimm dimm dimm dimm
i2c-nvram idprom motherboard-fru ppm beep fan-control
lomp
Probing Memory Bank #0 512 Megabytes
Probing Memory Bank #1 512 Megabytes
Probing Memory Bank #2 512 Megabytes
Probing Memory Bank #3 512 Megabytes
Probing /pci@1f,0 Device 7
Probing /pci@1f,0 Device 3
Probing /pci@1f,0 Device c ethernet
Probing /pci@1f,0 Device 5 ethernet
Probing /pci@1f,0 Device a usb
Probing /pci@1f,0 Device d ide disk cdrom
todm5819 Sun Fire V100 (UltraSPARC-IIe 648MHz), No Keyboard
OpenBoot 4.0, 2048 MB memory installed, Serial #53320536.
Ethernet address 0:3:ba:2d:9b:58, Host ID: 832d9b58.
Environment monitoring: disabled
ok boot
(again... did nothing)
please advice.
thanks in advance.
LOMlite starting up.
CPU type: H8/3437S, mode 3
Ram-test: 2048 bytes OK
Initialising i2c bus: OK
Searching for EEPROMs: 50(cfg)
I2c eeprom @50: OK
i2c bus speed code 01... OK
Probing for lm80s: none
Probing for lm75s: 48
Initialising lm75 @48: OK
System functions: PSUs fans breakers rails gpio temps host CLI ebus clock
LOMlite console
lom>
LOM event: +0h0m0s LOM booted
lom>poweron
(it does nothing...)
also when i turn the server on with the on/standby switch it also seems to be starting fine, but again when the ok prompt is displayed i try to execute commands and it does again nothing.
Firmware CORE Sun Microsystems, Inc.
@(#) core 1.0.18 2002/05/23 18:22
Software Power ON
Verifying NVRAM...Done
Bootmode is 0
MCR0 = 57b2ce06
MCR1 = 80008000
MCR2 = cff0ffff
MCR3 = b00003ff
Ecache Size = 512 KB
Clearing E$ Tags Done
Clearing I/D TLBs Done
Probing memory
Done
MEMBASE=0xc0000000
MEMSIZE=0x20000000
Clearing memory...Done
Turning ON MMUs Done
Copy ROM to RAM (154720 bytes) Done
Orig PC=0x1fff0007edc New PC=0xf0f07f34
Processor Speed=648MHz
Looking for Dropin FVM ... found
Decompressing Client Done
Transferring control to Client...
Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
Probing upa at 1f,0 pci
Probing upa at 0,0 SUNW,UltraSPARC-IIe (512 Kb)
Loading Support Packages: kbd-translator
Loading onboard drivers:
Probing /pci@1f,0 Device 7 isa dma rtc power SUNW,lomh serial serial
flashprom
Probing /pci@1f,0 Device 3 pmu i2c temperature dimm dimm dimm dimm
i2c-nvram idprom motherboard-fru ppm beep fan-control
lomp
Probing Memory Bank #0 512 Megabytes
Probing Memory Bank #1 512 Megabytes
Probing Memory Bank #2 512 Megabytes
Probing Memory Bank #3 512 Megabytes
Probing /pci@1f,0 Device 7
Probing /pci@1f,0 Device 3
Probing /pci@1f,0 Device c ethernet
Probing /pci@1f,0 Device 5 ethernet
Probing /pci@1f,0 Device a usb
Probing /pci@1f,0 Device d ide disk cdrom
todm5819 Sun Fire V100 (UltraSPARC-IIe 648MHz), No Keyboard
OpenBoot 4.0, 2048 MB memory installed, Serial #53320536.
Ethernet address 0:3:ba:2d:9b:58, Host ID: 832d9b58.
Environment monitoring: disabled
ok boot
(again... did nothing)
please advice.
thanks in advance.