LOG display shows 2800

[TheCurious]

1 LIM system BC11, reload from flash disk fails
LOG display shows 2800
It means that there is no NIU2 board found.
I switch off the power, than I switch it on. System counts 9064, 3100, 3110, 2800. I switch the power off and on again...I do it many times without success..Than suddenly NIU2 starts working, and I have 104 at the end, and PBX works OK.
I have also seen this strange behaviour before, it was NIU and SCSI disk.
Alex says that if there is 2800 on LOG display, than NIU, LSU, DSU should be checked.
Did anyone have this problem, and how did you solve this?
Should I concentrate on LSU/DSU or change/upgrade NIU2?


The Curious

 

[NIUX]

Hi,

Most probably it is an LSU problem.

BR///

 

[slash50]

YOu can try doing fuction test on the LSU/DSU's using

LSFTI:LIM=1,FULL=YES;

It's not a definitive test and it can be traffic disturbing. You could also try removing and replacing the NIU card. Check all the cables are correct also, and maybe remove and replace the LSU card.

Good luck

 

[TheCurious]

Hi people,

I have already tried with LSFTI, but results were OK.
System shows strange behaviour, for example BLFDP says that ELU29 in 1-0-30 is " faulty board", and when I move the same board to 1-0-40 it works OK.
ALLOP says that TMU is faulty, FTTDI says that board is faulty, FTMDI says faulty board, there is no dial tone in the system... But when I move TMU from 1-0-10 to 1-0-20, all alarms dissapear, and TMU works excellent.
Sometimes DUSYI to flash disk does not work, because of " buffer transfer error".
My conclusion is that LSU or DSU must be faulty. Why LSFTI did not find anything?

On the other hand, I took the NIU2 with me and tested it a little bit in the lab. In the lab I also had several 2800 states before disk started the normal reload.

Could be that both NIU2 and LSU are faulty. (?!)

The Curious

 

[whosrdaddy]

which firmware do you have on the NIU2 and what brand of flashdisk are you using?

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[slash50]

I think it's the DSU or a faulty backplane. The surefire way to test the DSU is to swap it with the DSU in another magazine and see if the fault follows it.

 

[TheCurious]

NIU board version:

001-0-60 NIU ROF 137 5396/2 R2A
CAA 1580021 R5A EXE
CAA 1580001 R13A OLD
001-0-70 LPU5 ROF1314602/3 R10C



Flash disk:

<IODDP;
I/O DEVICE DATA
NODE IODEV/SUBFS BPOS/EQU I/O-BUS TYPE/USAGE STATUS AUTH
SYSN - 001-0-60 - - IN SERVICE
SYSN SYSDISK1 001-0-60-0 MASTER TOSHIBA IN SERVICE
SYSSUBFS11
SYSSUBFS21
SYSN SYSTERMINAL 001-0-60-1 - MML - 7
SYSN TERMINAL2 001-0-60-2 - MML - 7
SYSN TERMINAL3 001-0-60-3 - MML - 7
SYSN ETHERNET 001-0-60-4 - NETWORK/MML - 7
END



ALLOP & HIMDP printouts when DUSYI failed:

VERSION: CXP1010010/5/BC11SP15/R5A

CLASS: 3
85 BUFFER TRANSFER HAS FAILED
DATE TIME ALP NOIF EQU BRDID INF1 INF2 INF3 INF4
29DEC05 10:16:17 2 1 001-0-60-00 106 330 0 1 1

CLASS: 1
38 DISTURB. COUNTER INCREASED DUE TO FAULTY PROGRAM EXECUTION
DATE TIME ALP NOIF EQU INF1
29DEC05 10:16:17 3 1 001-0-**-** 0

114 DEVICE BOARD HAS BEEN ACTIVATED
DATE TIME ALP NOIF EQU BRDID
29DEC05 10:17:00 4 1 001-0-60-00 106

CLASS: 0
56 THE SYSTEM DOES NOT HAVE AN ACCESSIBLE BACKUP
DATE TIME ALP NOIF EQU BRDID
29DEC05 10:16:14 1 1 001-0-60-00 106
RDATE RTIME
29DEC05 10:17:04

END

<HIMDP;

DIAGNOSTICS FROM OPERATING SYSTEM
TIME DATE
10:17:22 29DEC05
DIAGNOSTICS FROM LIM 001, LAST HIREI: HIREI NOT DONE

TIME DATE ERROR CODE
10:17:05 29DEC05 H'60
ADDRESS CONTROL FAILURE
LOGICAL PROGRAM ERROR ADDRESS = 020011AC
ENTER
SWSW B-LEVEL SIGNAL COMEX (H'0077)
FROM ICM (H'012) EXE A IN LIM 001
TO TWP3 (H'057) EXE A IN LIM 001
NUMBER OF DATA BYTES IN SIGNAL = 7
WITH 0 1 2 3 4 5 6 7 8 9
000 02 1C 00 05 07 07 02
STACK ADDRESS = 0200A5EE
SIGNAL SEND ADDRESS = 0200D2E6


TIME DATE ERROR CODE
10:16:17 29DEC05 H'14
JUMP TO ILLEGALSTATE
LOGICAL PROGRAM ERROR ADDRESS = 0201D308
BRANCHVALUE = 00000000
ENTER
HWSW B-LEVEL SIGNAL CLOSEHWRES (H'0006)
FROM DEVICE EQU NO 1-0-60-00
TO NIP (H'056) EXE A IN LIM 001
NUMBER OF DATA BYTES IN SIGNAL = 8
WITH 0 1 2 3 4 5 6 7 8 9
000 00 00 00 00 FF FF 00 09
STACK ADDRESS = 00000000
SIGNAL SEND ADDRESS = 00000000

USER STACK DUMP
0 1 2 3 4 5 6 7 8 9 A B C D E F
02 01 61 F2 02 00 94 5E

TIME DATE ERROR CODE
10:08:58 29DEC05 H'60
ADDRESS CONTROL FAILURE
LOGICAL PROGRAM ERROR ADDRESS = 02004EAE
ENTER
SWSW B-LEVEL SIGNAL PRNOK (H'005C)
FROM OCM (H'017) EXE A IN LIM 001
TO DRDH (H'01D) EXE A IN LIM 001
NUMBER OF DATA BYTES IN SIGNAL = 4
WITH 0 1 2 3 4 5 6 7 8 9
000 00 02 03 01
STACK ADDRESS = 00000000
SIGNAL SEND ADDRESS = 020036D4


TIME DATE ERROR CODE
10:08:38 29DEC05 H'14
JUMP TO ILLEGALSTATE
LOGICAL PROGRAM ERROR ADDRESS = 0200337A
BRANCHVALUE = 00000002
ENTER
SWSW A-LEVEL SIGNAL *************** (H'0000)
FROM PRP (H'004) EXE A IN LIM 001
TO FIP (H'04F) EXE A IN LIM 001
NUMBER OF DATA BYTES IN SIGNAL = 1
WITH 0 1 2 3 4 5 6 7 8 9
000 01
STACK ADDRESS = 00000000
SIGNAL SEND ADDRESS = 020009BC

USER STACK DUMP
0 1 2 3 4 5 6 7 8 9 A B C D E F
02 00 33 5C 02 00 2B D6 02 00 29 C0 02 00 20 E8

TIME DATE ERROR CODE
10:08:38 29DEC05 H'21
INVALID DATA AT CENTRALIZED TIME MEASUREMENT
ENTER
SWSW A-LEVEL SIGNAL REMCTMA (H'003B)
FROM FIP (H'04F) EXE A IN LIM 001
TO PRP (H'004) EXE A IN LIM 001
NUMBER OF DATA BYTES IN SIGNAL = 6
WITH 0 1 2 3 4 5 6 7 8 9
000 00 4F 08 08 EC 98
STACK ADDRESS = 020029C0
SIGNAL SEND ADDRESS = 02002B64


TIME DATE ERROR CODE
09:55:23 29DEC05 H'14
JUMP TO ILLEGALSTATE
LOGICAL PROGRAM ERROR ADDRESS = 0200337A
BRANCHVALUE = 00000002
ENTER
SWSW A-LEVEL SIGNAL *************** (H'0000)
FROM PRP (H'004) EXE A IN LIM 001
TO FIP (H'04F) EXE A IN LIM 001
NUMBER OF DATA BYTES IN SIGNAL = 1
WITH 0 1 2 3 4 5 6 7 8 9
000 01
STACK ADDRESS = 00000000
SIGNAL SEND ADDRESS = 020009BC

USER STACK DUMP
0 1 2 3 4 5 6 7 8 9 A B C D E F
02 00 33 5C 02 00 2B D6 02 00 29 C0 02 00 20 E8

TIME DATE ERROR CODE
09:55:23 29DEC05 H'21
INVALID DATA AT CENTRALIZED TIME MEASUREMENT
ENTER
SWSW A-LEVEL SIGNAL REMCTMA (H'003B)
FROM FIP (H'04F) EXE A IN LIM 001
TO PRP (H'004) EXE A IN LIM 001
NUMBER OF DATA BYTES IN SIGNAL = 6
WITH 0 1 2 3 4 5 6 7 8 9
000 00 4F 08 08 EC B2


TIME DATE ERROR CODE
09:53:38 29DEC05 H'24
RELOAD DATA CHANGE FORBIDDEN
LOGICAL PROGRAM ERROR ADDRESS = 02014DFA
ENTER
SWSW B-LEVEL SIGNAL ACTIVATEANS (H'0026)
FROM ELP6 (H'19D) EXE A IN LIM 001
TO DCP (H'07E) EXE A IN LIM 001
NUMBER OF DATA BYTES IN SIGNAL = 3
WITH 0 1 2 3 4 5 6 7 8 9
000 08 00 02
STACK ADDRESS = 00000000
SIGNAL SEND ADDRESS = 0200CE56


TIME DATE ERROR CODE
09:52:46 29DEC05 H'14
JUMP TO ILLEGALSTATE
LOGICAL PROGRAM ERROR ADDRESS = 020143CA
BRANCHVALUE = 00000001
ENTER
SWSW B-LEVEL SIGNAL READWRITEBRDRES (H'0070)
FROM ELP6 (H'19D) EXE A IN LIM 001
TO DCP (H'07E) EXE A IN LIM 001
NUMBER OF DATA BYTES IN SIGNAL = 62
WITH 0 1 2 3 4 5 6 7 8 9
000 00 A0 06 52 31 41 2D 20 43 41
010 41 31 31 32 32 39 31 35 00 00
020 00 00 00 00 00 00 BC 60 88 00
030 00 00 00 AC 00 00 00 00 46 01
040 AA 55 AA 55 AA 55 03 FF FF FF
050 FF FF FF FF FF FF FF FF FF FF
060 FF FF
STACK ADDRESS = 00000000
SIGNAL SEND ADDRESS = 0200A7E0

USER STACK DUMP
0 1 2 3 4 5 6 7 8 9 A B C D E F
02 00 0D 50

TIME DATE ERROR CODE
09:52:46 29DEC05 H'14
JUMP TO ILLEGALSTATE
LOGICAL PROGRAM ERROR ADDRESS = 020143CA
BRANCHVALUE = 00000001
ENTER
SWSW B-LEVEL SIGNAL READWRITEBRDRES (H'0070)
FROM ELP6 (H'19D) EXE A IN LIM 001
TO DCP (H'07E) EXE A IN LIM 001
NUMBER OF DATA BYTES IN SIGNAL = 62
WITH 0 1 2 3 4 5 6 7 8 9
000 00 A0 0A 28 45 4C 55 32 39 20
010 20 20 20 20 20 20 52 4F 46 31
020 33 37 35 33 33 39 2F 31 31 20
030 20 20 20 20 20 20 52 31 30 4A
040 20 20 20 20 00 00 00 FF FF FF
050 FF FF FF FF FF FF FF FF FF FF
060 FF FF

USER STACK DUMP
0 1 2 3 4 5 6 7 8 9 A B C D E F
02 00 0D 50

TIME DATE ERROR CODE
09:51:34 29DEC05 H'14
JUMP TO ILLEGALSTATE
LOGICAL PROGRAM ERROR ADDRESS = 020143CA
BRANCHVALUE = 00000000
ENTER
SWSW B-LEVEL SIGNAL BORDIDENTY (H'001E)
FROM ELP6 (H'19D) EXE A IN LIM 001
TO DCP (H'07E) EXE A IN LIM 001
NUMBER OF DATA BYTES IN SIGNAL = 9
WITH 0 1 2 3 4 5 6 7 8 9
000 00 AF 00 57 CF 01 9D 02 60
STACK ADDRESS = 00000000
SIGNAL SEND ADDRESS = 0200A600

USER STACK DUMP
0 1 2 3 4 5 6 7 8 9 A B C D E F
02 00 05 1A

END

<LSFTI:LIM=1,FULL=YES;
LSFTI:LIM=1,FULL=YES;
SURE? (YES/NO)
<Y;
ORDERED
CAUTION:TRAFFIC DISTURBING TEST IS PERFORMING
<;
SYNTAX ERROR

SPONTANEOUS PRINTOUT

LIM SWITCH FUNCTION TEST RESULT FOR LIMNO 1
LSU CM : OK
AM : OK
PROM : OK
RAM : NO TEST PERFORMED
CLOCK : OK
HDLC : NO TEST PERFORMED
PCM-FREE : OK
PCM-BUSY : OK
BOARD PROM RAM FEEDBACK DB-ADDR P/U-SIGN FREQ
DSU 0 OK OK OK OK OK OK
DSU 1 NO CONTACT
DSU 2 NO CONTACT
DSU 3 NO CONTACT

END

The Curious

 

[whosrdaddy]

Toshiba flashdisks NEED at least firmware revision R8A, but it is better to update to R9A.

Sandisk flashdisk will give no problem in R5A

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!