line lock-out

[MATOVTZ]

Hi!
I have Octel 100 with MD110. Analog line is lock-out. Restart with power OFF-ON is not help. I can't connect direct on Octel100 because I am on other site.
What I can do?
BR

 

[joeOctel]

You probably need to be onsite to check and determine if the problem is on the MD110 side or the Octel 100 side. See if you have dial tone and whether the analog line rings and answers the call.

 

[doktor]

Are you sure that it is an OCTEL 100 and not a VMX-100.
There is quite a difference.
Please find out what type it is.
BR doktor

 

[MATOVTZ]

That is VMX-100 and I will connect:

TYPE SLOT CHNL PRIO DATE TIME #BAD DATA1 DATA2 DATA3 DATA4
02 01 01 2 08/31 10:00 4 07 00 01 00
02 01 02 2 08/31 10:00 4 07 00 01 00

I will try TEST line and test is bad, but I have only one LIC board and can't change it.

BR

 

[doktor]

I have copied the details from the Installation and Maintenance Manual:
The fault deals with Tone Refection.
Clear Hardware Error Table by C H at the @-prompt.
Run TE L 1 again. If error repeat, replace the LIC-2.
If all lines fail, check configuration or Main Board as possible cause. If Error repeats, replace MB and metal case.

What does the BLFDP; say in the MD110.
It can be the LIC-2 or the configuartion in the VMX or MD110. Have you changed anything in the two systems??
Did you have other alalrms in the VMX-100 or MD110 before this fault?.
Do you use a proper grounding between the MD110 and the VMX-100?
Maybe I can supply a LIC-2 if needed.
Please remember that the VMX-100 has been phased out by both Ericsson and OCTEL/AVAYA.
Yours ///doktor

 

[doktor]

See more interesting info in "thread923-831490"

///doktor

 

[MATOVTZ]

I change LIC card but it is same. When I add LIC card in VMX-100 ports on this board is ok but ports on first card is always busy.

.L PORT

PORT EXTENSION# COS MODE OUTCALL TEST
---- ---------- --- ---- ------- ----
1 2561 127 AX YES YES
2 2562 127 AX YES YES
3 2525 127 AX YES YES
4 4104 127 AX YES YES
.
@L H
THU 09/15 17:43:30 2005 ID:11 S/N:115021 PBX:58
CLEARED: 09/15 17:29

TYPE SLOT CHNL PRIO DATE TIME #BAD DATA1 DATA2 DATA3 DATA4
02 01 01 2 09/15 17:39 1 07 00 01 00
02 01 02 2 09/15 17:39 1 07 00 01 00
@PS

CH 1 CH 2 CH 3 CH 4
TST TST IDL IDL


@TE L 1
CHANNEL TESTED BAD, CHAN. #= 1
CHANNEL TESTED BAD, CHAN. #= 2
TEST01 COMPLETE
@TE L 2
TEST02 COMPLETE
@PS

CH 1 CH 2 CH 3 CH 4
IDL IDL IDL IDL


@

but after some time ports on first LIC is busy and other ports is working ok.

 

[doktor]

MATOVTZ!

We have some systems running with port 3+4 (LIC-2 in second slot), with no analogue connections to the MD110.
So maybe you can use your system with port 1+2 (on LIC-2 in the first slot).
It must some defective part of the mother board that gives you this problem.

doktor

 

[doktor]

Have you checked the lines from the MD110 by the way?
Is there some kind of line lock in the MD on the two first ports?? Have you tried to swap the lines from the MD110?

doktor

 

[doktor]

My first post from today 17. Sept 2005 has some missing parts of info. Here is it:
We have some systems running with port 3+4 (LIC-2 in second slot), with no analogue connections to the MD110.
So maybe you can use your system with port 1+2 (on LIC-2 in the first slot), without having any analogue lines connected to port=1+2.
Instead your lines should be connected to port 3+4 or more.
It must some defective part of the mother board that gives you this problem.
You will have to reprogram your MD110, if you change port numbers in the VMX-system.

doktor

 

[MATOVTZ]

I now use VMX with two LIC-2 card with port 3+4 and working ok.
Thanks doktor for help!