LCR - Extension category

[trond456]

I do have the following scenario.. 4 routes programmed for LCR and working fine...the customer asked if they can use the land lines route in case that the mobile route is busy as an alterantive (2nd cheapest) and this is also done by using RODDI:.., cho=1;

but could this (using the second cheapest trunk)be based on extension category.. I mean I want to give this facility(2nd cheapet) only for managers not for all emplyess..

I tried to use FRL and ROC in kscac but no success.

Is there any advice or do u have an example for a solution.
Regards

 

[Isinor]

Hi,

Have a look at extension parameter ROC and route parameter ACD...

EXCAC:ROC=... digit 3
RODDI:ROU=..,CHO=..,ADC=..?? Digits 10 & 11

Good luck


Regards
Isinor

 

[parnum]

or depending on your setup you can use TCMAP

regards parnum

 

[trond456]

Hi,,

ROC doesnt say if the extension is not permitted to use the cho=1 in RODDI in case the cheapaest is busy, on contrary it says search for a free route is done...????!!!!
(could this be done first)??


KSCAPIR=200&&201;KEY SYSTEM CATEGORY PRINT
DIR TRAF SERV CDIV ROC ITYPE TRM ADC LANG BSEC
200 01151515 0000100300 001151111 200001 26 0 00000000000000 0 0
201 01151515 0000100300 001151111 002001 26 0 00000000000000 0 0

this is my ROC.. do u have any comments... 201 is a manager and can use the land route in case the mobile line is busy and this is ok..
but directory 200 is an employee and not permitted to use the land line in case of the mobile line is busy but this not acheived with these parameter..(I dont want want the employee 200 to use land lines to make mobile calls in case mobile route is busy)
do u have any example or comments for paarmeters above.

RODDPEST=ALL;EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
5 1 0005000000000250000000000 0 2
6 2 0005000000000250000000000 0 2
1 1 0005000000000250000000000 0 2
7 3 0005000000000250000000000 0 2

Any comments....

CDDP:TAB=DNT2;LEAST COST DESTINATION DATA
NUMBER TABLE
ENTRY TRC PRE ACCT FRCT TOLL CBCS BTON TNS OSA
9077 1 0 3 111111111111111 0
9079 1 0 2 111111111111111 0
94 1 0 1 111111111111111 0
95 1 0 1 111111111111111 0
END

LCDDP:TAB=FDT;LEAST COST DESTINATION DATA
FICTITIOUS DESTINATION TABLE
FRCT TZONE PRE
1 1 5
2 1 6
3 1 7


note 9077--DEST 7 &9079---DEST 6 are mobile... 95--DEST 5 is land

any comments

Pls advise if u have example

 

[cfrei]

Hi,
FRL works only in transit exchange. Try CUST.

 

[Isinor]

Hi,

ROC sets the extension to a LCR class...

The RODDI command ACD D9 controls what extension can use the DEST.

...all employees
EXCACIR=200,ROC=000151111;

...for managers
EXCACIR=201,ROC=003151111;

The Alternate route programming...
RODDIEST=6,CHO=1,ROU=1,ADC=0005000001000250000000000,SRT=...etc;



Regards
Isinor

 

[trond456]

Thanks alot for the support.. scenario works fine now

 

[lalrl]

Isinor: you mean D10 in ADC?

 

[kank]

Hi,
Did you try doing it with customer?
Give a customer number to managers and on roddi use cust parameter for alternate so only managers will be able to get these lines.

Regards..

 

[Isinor]

lalrl... Isinor: you mean D10 in ADC?

Oops... yep D10...

Regards
Isinor